Edelbrock 6893 Bedienungsanleitung

Catalog #6893 &#6894 Page 1of 3 Rev. 1/03

TUBULAR EXHAUST SYSTEM (T.E.S.)

Catalog #6893- 1993 Camaro/Firebird, 5.7L V8,

Standard and Auto Transmission, with A.I.R.

Catalog #6894- 1994-1995 Camaro/Firebird, 5.7L V8

Standard and Auto Transmission, with A.I.R.

INSTALLATION INSTRUCTIONS

Please study these instructions carefully before installing your new Tubular Exhaust System (TES). If you have any

questions or problems, please call our Technical Hotline: 1-800-416-8628, 7am - 5pm, Monday-Friday, Pacific

Standard Time or e-mail us at: [email protected].

DESCRIPTION: These components are designed as a system to improve the exhaust efficiency of the GM 350 c.i.d. V8

engines. A performance gain can be expected by the installation of the system. This system requires welding for

installation and retains all O.E.M. emissions equipment.

SUGGESTED TOOLS FOR INSTALLATION: This vehicle has some metric fasteners.

❑ MIG welder (recommended) or gas welder. Professional welding is highly recommended.

❑ 3/8” rachet socket set with extensions and universal 13mm and 15mm swivel sockets

❑ Combination set of open-end wrenches

❑ Hack saw

❑Jackstands, screwdrivers, pliers, crescent wrench, etc.

❑Liquid penetrant, (GM #1052627) anti-seize compount(GM #5613695)

SPECIAL NOTICE: This Edelbrock part has received an Executive Order number (E.O.) from the California Air Resources

Board (C.A.R.B.) making it legal for street use on pollution-controlled motor vehicles in all 50 states. To assist you with

emissions equipment certification, we have included a silver fan shroud decal to verify that this part is a legal replacement

part on the vehicle for which it is cataloged. The adhesive-backed decal should be affixed to your fan shroud next to the

existing emission and engine specification decal. Do not cover your original equipment specification decal with the

Edelbrock fan shroud decal.

WARNING: The use of “Thermal Wrap” or any aftermarket coating process will void the warranty on your Tubular Exhaust

System. Those products can cause excessive heat and moisture buildup resulting in corrosion and early failure of the

system.

NOTES: The paint used on non-coated T.E.S. is for protection during shipping and storage and will burn off soon after the

engine is started. Those who desire a longer lasting finish should sand blast the T.E.S. to remove the original paint, then

apply high temperature header paint, such as VHT, available at most auto parts stores. High temperature spark plugs

wires and boots are recommended to withstand heat from T.E.S.

Catalog #6893 &#6894 Page 2of 3 Rev. 1/03

DISASSEMBLY AND ASSEMBLY

Right Side

1. Disconnect and remove alternator.

2. Remove spark plugs.

3. Disconnect A.I.R. fitting from manifold.

4. Remove dipstick and tube assembly.

5. Unbolt E.G.R. flange from manifold (#6894 only).

6. Remove manifold.

Note: At front of cylinder head are two manifold

boltholes. Forward hole will be used to re-attach

alternator support bracket. Hole #2 will be used to

secure your new T.E.S. manifold.

7. Install T.E.S. flange gasket and one 3/8-16 x 1” bolt,

lock washer and flat washer at rearmost bolthole

(leave bolt loose enough to accept T.E.S.).

8. Place manifold into position from underneath

vehicle and start one bolt at front.

Note: Use flat washers at slotted ends and lock

washers on all bolts.

9. Using 1-1/8 long spacer tube, 3/8 x 2-1/4 12-point

head cap screw and 3/8 lock washer, re-attach

alternator support bar to forward bolthole in

cylinder head (do not tighten).

10. Install all manifold bolts and tighten.

11. Re-attach E.G.R. tube (#6894 only).

12. Re-install spark plugs and wires.

Note: Alternator and dipstick tube must be

removed for future spark plug changes.

13. Re-install alternator and A.I.R. fitting. Use A.I.R.

adapter fitting and kit, if necessary.

14. Re-install dipstick tube.

15. Take wire pack (wrapped with aluminum tape) out

of plastic clip on crossmember and re-position

toward front of vehicle for additional protection

from heat. Use tie wrap (in kit) to secure.

Left Side

1. Remove spark plugs.

2. Unplug temperature sensor wire connector.

3. Remove plastic cover around lower steering shaft.

Steering shaft must be removed for installation of

T.E.S.

4. Remove by unbolting at top of upper universal joint

andbottom oflower universaljoint. Slip upperjoint

up steering shaft while sliding lower joint off

steering box serrated shaft.

5. Disconnect A.I.R. hose.

6. Remove exhaust manifold.

7. Install T.E.S. flange gasket and one 3/8”-16 x 1”

bolt, lock washer and flat washer at rearmost

bolthole (leave bolt loose enough to accept T.E.S.).

8. Place manifold into position from above. Start all

manifold bolts, and washers, then tighten.

9. Replace steering shaft and plastic cover.

10. Replace water temperature wire.

11. Replace spark plugs and wires.

12. Re-install A.I.R. fittings (use A.I.R. adapter fitting in

kit, if necessary).

1. Disconnect negative battery cable.

2. Raise vehicle and remove O2 sensors from right and left sides being careful not to damage.

3. Unbolt and remove exhaust pipe/catalytic converter assembly. Before removing exhaust pipe/catalytic converter

assembly determine the position of catalytic inlet for re-installation. Either note measurements or mark bottom of

floorboard with chalk to show catalytic location (Do not damage converter).

INSTALLATION INSTRUCTIONS

Catalog #6893 &#6894 Page 3of 3 Rev. 1/03

Extension Pipe

1. Cut O.E.M. exhaust pipe approximately 1/2” to 3/4” in front of the catalytic.

2. Bolt catalytic back into vehicle with front in original location.

3. Install T.E.S. pipe over catalytic inlet and bolt to T.E.S. manifold using donut gaskets provided.

4. With everything in place, tack weld T.E.S. to catalytic.

Note: Tig welding is desirable but gas welding can be used.

5. After tack welding, remove assembly and complete weld.

6. Re-install assembly and tighten all bolts.

7. Check all wires and lines for adequate clearance.

FINAL INSPECTION

1. Check all hydraulic, vacuum, and fuel lines to ensure there is adequate clearance to T.E.S. components.

2. Re-connect battery.

3. At this point, it is a good idea to look everything over and make sure nothing was missed in assembly.

4. Start vehicle and bring up to normal operating temperature. Check for possible leaks.

5. Turn engine off and let cool. Tighten all bolts again.

KIT CONTENTS

Qty. Part # Description Qty. Part # Description

125-9070 Manifold Left Side 12 -Hex Header Bolts; 3/8” x 1”

125-9071 Manifold Right Side (#6893) 1-Spacer Tube; 5/8” s 1-1/8” Long

125-9075 Manifold Right Side (#6894) 4-Hex Capscrews; 3/8” x 2”

125-9583 ExtensionY-pipe 1-Hex Capscrews; 12-point head,

3/8” x 2-1/4”

2-Chevy V8 Port Gaskets 16 -Lock Washers; 3/8”

2-Donut Gasketss; 2-1/2” 1-Tie Wrap; 11”

4-Flat Washers; 3/8” 2-Fittings; A.I.R. Adapter

Edelbrock Corporation

2700 California St.

Torrance, CA 90503

Tech Line: 1-800-416-8628

E-Mail: [email protected]

Dieses Handbuch passt für folgende Modelle

Andere Edelbrock Automobilteil Handbücher

Edelbrock

Edelbrock Victor Jr. 70067 Bedienungsanleitung

Edelbrock

Edelbrock 66092 Bedienungsanleitung

Edelbrock

Edelbrock 71883 Bedienungsanleitung

Edelbrock

Edelbrock 15002 Bedienungsanleitung

Edelbrock

Edelbrock 66042 Bedienungsanleitung

Edelbrock

Edelbrock 47493 Bedienungsanleitung

Edelbrock

Edelbrock 4250 Bedienungsanleitung

Edelbrock

Edelbrock Cat-Back Exhaust System 5714 Bedienungsanleitung

Edelbrock

Edelbrock 4789 Bedienungsanleitung

Edelbrock

Edelbrock 17934 Bedienungsanleitung

Edelbrock

Edelbrock 25-9492 Bedienungsanleitung

Edelbrock

Edelbrock Performer 1670 Bedienungsanleitung

Edelbrock

Edelbrock Edelbrock Headers 65632 Bedienungsanleitung

Edelbrock

Edelbrock 67452 Bedienungsanleitung

Edelbrock

Edelbrock 5426 Bedienungsanleitung

Edelbrock

Edelbrock 6719 Bedienungsanleitung

Edelbrock

Edelbrock 5280 Bedienungsanleitung

Edelbrock

Edelbrock 5672 Bedienungsanleitung

Edelbrock

Edelbrock 5644 (Aluminized) Bedienungsanleitung

Edelbrock

Edelbrock Torker II 5021 Bedienungsanleitung

Edelbrock

Edelbrock 5769 Bedienungsanleitung

Edelbrock

Edelbrock 3844 (65mm) Bedienungsanleitung

Edelbrock

Edelbrock SBC Vortec 283-400 c.i.d. Chevy V8 Bedienungsanleitung

Edelbrock

Edelbrock 4742 Bedienungsanleitung

Beliebte Automobilteil Handbücher anderer Marken

Dakota Digital

Dakota Digital 650277 Bedienungsanleitung

bosal

bosal 037031 Bedienungsanleitung

Vintage Air

Vintage Air 571063 Bedienungsanleitung

GFB

GFB EX38 Bedienungsanleitung

bosal

bosal 028091 Bedienungsanleitung

Dodge

Dodge 8W-43 Kurzanleitung

ICI

ICI Magnum FBM10DGN Bedienungsanleitung

Volant Perfomance

Volant Perfomance 19435 Bedienungsanleitung

BENDIX

BENDIX GEN 4 GEN 5 ABS Bedienungsanleitung

Vintage Air

Vintage Air 571065 Bedienungsanleitung

Rugged Ridge

Rugged Ridge 11503.13 Bedienungsanleitung

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Bedienungsanleitung

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Leitfaden

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Bedienungsanleitung

Toshiba

Toshiba 48-1250 A Bedienungsanleitung

aldes

aldes EHT2 Bedienungsanleitung

Go Rhino

Go Rhino 24371T Bedienungsanleitung

BBK

BBK 18950 Bedienungsanleitung