Edelbrock Russell R09783 Bedienungsanleitung

Rev. 7/06 - BC/mc

Catalog #R09783

Brochure #63-R09783

Page 1 of 2

Catalog #R09783

DOT Racer Front Brake Hose Kit

for 2006 Yamaha YZF-R6

INSTALLATION INSTRUCTIONS

1. Remove factory brake hose assembly and related hardware, noting routing. Plug master cylinder and caliper

ports.

2. For easier hose installation, mark master cylinder orientation on handlebar and remove.

3. Unplug horn and remove horn bracket/dust shield assembly from fork tree and then remove horn from bracket.

4. Bend brake hose junction block locating tab on horn bracket flat for hose clearance

(See Fig. 1).

5. Install side-bent banjo end of Russell right-side hose onto caliper so that banjo bends around front of locating tab

(See Fig. 2).

Locate hose to fork with factory bracket around hose grommet.

6. Install slight-bent (20°) banjo end of Russell left-side hose onto caliper so that banjo bends inward and is oriented

towards factory fork mounting point

(See Fig. 3)

. Locate hose to fork with factory bracket around hose grommet.

Please study these instructions carefully before installing your new Brake Hose Kit. If you have any questions, please call

our Technical Hotline at: 1-800-416-8628, 7:00 am - 5:00 pm, Pacific Standard Time, Monday through Friday or

e-mail us at [email protected].

INSTALLATION INSTRUCTIONS

IMPORTANT NOTE: Do not allow the master cylinder to completely drain of brake fluid at any time during this process.

Also, use care when handling brake fluid, as it can quickly damage finished surfaces (paint, plating, etc.).

Fig. 1 Fig. 2 Fig. 3

IMPORTANT NOTE:

Proper installation is the responsibility of the installer. Improper installation will void warranty and may

result in poor performance and engine or vehicle damage.

Rev. 7/06 - BC/mc

Catalog #R09783

Brochure #63-R09783

Page 2 of 2

Edelbrock Corporation, 2700 California Street, Torrance, CA 90503

Toll-Free Tech Line: 1-800-416-8628

Tech E-Mail: [email protected]

7. Route hoses behind forks and pull out between front fairing and fender. Install supplied cushion clamp over both

hoses so that mounting hole is to left and clamp/hoses are offset to front. Place horn bracket over hoses. Attach

hoses to bracket by inserting factory junction block bolt through cushion clamp and supplied nylon spacer and

threading into factory junction block mounting hole

(See Fig. 4, shown installed on fork tree, top view)

Leave bolt finger-tight. Re-install horn to bracket.

8. Route hoses behind front fairing and re-install horn bracket/dust shield assembly to fork tree.

9. Insert supplied double banjo bolt through both banjo hose ends, with right-side banjo on bottom. Thread banjo

bolt into master cylinder until finger-tight. Re-install master cylinder onto handlebar, orienting with mark made

earlier. Orient hoses so that banjos point forward over throttle cables, with left banjo to outside of right banjo

(See Fig. 5)

. Tighten banjo bolt.

10. Use supplied cable tie to hold hoses to fork just above fork clamp. Route hoses underneath factory plastic hold-

down. Pull any remaining slack in hoses down through cushion clamp. Orient cushion clamp so hoses and clamp

do not contact horn and tighten clamp bolt

(See Fig. 6)

. Plug in horn.

11. Check hose clearance throughout entire steering and suspension travel range.

12. Bleed the system and check for leaks while applying pressure.

Fig. 4 Fig. 5 Fig. 6

Inhaltsverzeichnis

Andere Edelbrock Automobilteil Handbücher

Edelbrock

Edelbrock 5291 Bedienungsanleitung

Edelbrock

Edelbrock 70028 Bedienungsanleitung

Edelbrock

Edelbrock 5734 Bedienungsanleitung

Edelbrock

Edelbrock 47480 Bedienungsanleitung

Edelbrock

Edelbrock 63-0358 Bedienungsanleitung

Edelbrock

Edelbrock ENDURASHINE 63-0299 Bedienungsanleitung

Edelbrock

Edelbrock 68452 Bedienungsanleitung

Edelbrock

Edelbrock 65102 Bedienungsanleitung

Edelbrock

Edelbrock 5694 (Stainless Steel) Bedienungsanleitung

Edelbrock

Edelbrock Russell R09761 Bedienungsanleitung

Edelbrock

Edelbrock 5758 Bedienungsanleitung

Edelbrock

Edelbrock 70402 Bedienungsanleitung

Edelbrock

Edelbrock 16211-MBN-640 Betriebsanleitung

Edelbrock

Edelbrock 78001 Bedienungsanleitung

Edelbrock

Edelbrock 6876 Bedienungsanleitung

Edelbrock

Edelbrock 5276 Bedienungsanleitung

Edelbrock

Edelbrock Performer 1670 Bedienungsanleitung

Edelbrock

Edelbrock 2980 Bedienungsanleitung

Edelbrock

Edelbrock 5260 Bedienungsanleitung

Edelbrock

Edelbrock 8135 Bedienungsanleitung

Edelbrock

Edelbrock 3714 Bedienungsanleitung

Edelbrock

Edelbrock 5737 Bedienungsanleitung

Edelbrock

Edelbrock 72310 Bedienungsanleitung

Edelbrock

Edelbrock 2166 Bedienungsanleitung

Beliebte Automobilteil Handbücher anderer Marken

Dakota Digital

Dakota Digital 650277 Bedienungsanleitung

bosal

bosal 037031 Bedienungsanleitung

Vintage Air

Vintage Air 571063 Bedienungsanleitung

GFB

GFB EX38 Bedienungsanleitung

bosal

bosal 028091 Bedienungsanleitung

Dodge

Dodge 8W-43 Kurzanleitung

ICI

ICI Magnum FBM10DGN Bedienungsanleitung

Volant Perfomance

Volant Perfomance 19435 Bedienungsanleitung

BENDIX

BENDIX GEN 4 GEN 5 ABS Bedienungsanleitung

Vintage Air

Vintage Air 571065 Bedienungsanleitung

Rugged Ridge

Rugged Ridge 11503.13 Bedienungsanleitung

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Bedienungsanleitung

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Leitfaden

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Bedienungsanleitung

Toshiba

Toshiba 48-1250 A Bedienungsanleitung

aldes

aldes EHT2 Bedienungsanleitung

Go Rhino

Go Rhino 24371T Bedienungsanleitung

BBK

BBK 18950 Bedienungsanleitung