Ekwb EK-PRO GPU WB RTX A100 Bedienungsanleitung

USER GUIDE

GPU WATER BLOCK

EK-PRO

GPU WB RTX A100

Before you start using this product, please follow these basic guidelines:

Carefully read the manual before beginning with the

installation process.

Remove your graphics card from the computer for the safest

mounting process to prevent any possible damage to your

GPU or its circuit board (PCB).

EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured with the

rubber O-ring gaskets.

The use of quality market-proven corrosion-inhibiting

coolants is always strongly recommended for any liquid

cooling system.

Do not use pure distilled water as a cooling liquid! For best

results, EK recommends the use of EK-CryoFuel Coolants.

Make sure to bleed air out of your water block thoroughly in

order to reach optimal performance.

- 3 -

TABLE OF CONTENTS

BOX CONTENTS 4

WATER BLOCK DIMENSIONS 5

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS 6

PREPARING YOUR GRAPHICS CARD 7

REMOVING THE STOCK COOLER 7

CLEANING THE PCB 7

CUTTING AND PLACING THERMAL PADS 8

APPLYING THERMAL COMPOUND 8

INSTALLING THE WATER BLOCK 9

PLACING THE BLOCK ON THE GRAPHICS CARD 9

ATTACHING THE WATER BLOCK 9

CHECKING THE CONTACT IN CASE OF HIGH TEMPERATURES 11

INSERTING THE GRAPHICS CARD INTO THE CHASSIS 12

TESTING THE LOOP 12

SUPPORT AND SERVICE 13

SOCIAL MEDIA 13

- 4 -

EK-PLUG G1/4 (2x)

3830046999153

Allen Key 2.5mm (1x) 8902

Allen Key 2mm (1x) 8901

120 mm

24 mm

BOX CONTENTS

Nut M2.5 (6x) 8506

Screw M2.5x4 ax1 (16x)

9047

EK-Loop Multi Allen Key (1x)

3830046996213

Screw M2.5x8 ax1 (2x) 8104A

Screw M3x6 DIN 7991 (2x) 9029

Thermal PAD F 1.0mm - (120x16mm)

(2x) 3830046996732

Screw M3x4 DIN7985 (2x)

8123

EK-TIM Ectotherm (1g) (1x)

3830046998446

Screw M3x6 ISO 14581 - TX-INOX

(2x) 103090

Screw UNC 6/32x5 (1x) 8483

EK-Pro GPU WB RTX A100 Ni +Inox (1x)

3831109847961

Washer POLYAMID M2.5 0.7mm

with self-adhesive tape (2x) 8627

Thermal PAD G 1.0mm - (120x24mm)

(2x) 3830046996770

120 mm

16 mm

Washer

POLYAMID M2.5 0.5mm

(16x) 8623

Screw M2.5x6 ax1 (13x)

9058

- 5 -

WATER BLOCK DIMENSIONS

278.4 mm

267 mm

134.2 mm

104.3 mm

97 mm

19.5 mm

134.2 mm

97 mm

13.6 mm

46.5 mm

75.5 mm

- 6 -

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS

Position EAN Description Quantity

1103704

055 - copper - RTX A100 Pro coldplate (Ni)

2103716

055 - top acetal - A100 insert

35028

OR 5x1,5 NBR70

45196

OR 180x2

5103090

Screw M3x6 ISO 14581 - TX-INOX

6100845

Spacer M4/M2.5x2.5 - HEX

7103767

top acetal - FC terminal Direct (2x G1-4)

8103713

054 - metal power adapter

9103705

055 - metal - RTX A100 Pro Top Inox

10 100006

Screw M4x27 DIN7984

11 5155

OR 15x1 EPDM50 (FC Terminal)

12 102490

Medenina - Pro GPU Bracket standoff M4-6/32 - Ni

13 8625

Washer POLYAMID M2.5 0,7mm with

self-adhesive tape

- 7 -

PREPARING YOUR GRAPHICS CARD

STEP 1

REMOVING THE STOCK COOLER

Place your graphics card on the ﬂat surface and carefully remove

the stock cooler. Do not forget to unplug all the LED and fan

connectors. Pay attention to the following steps in order to install

the EK-Pro GPU RTX A100 water block onto the graphics card.

STEP 2

CLEANING THE PCB

Wipe off the remains of the original thermal compound using a

nonabrasive cloth or Q-tip, as shown in the sample image, until the

components and circuit board are completely clean. EK recommends

the use of denatured alcohol for removing TIM leftovers. After that,

remove all remaining stock thermal pads from the PCB.

STEP 2

- 8 -

CUTTING AND PLACING THERMAL PADS

Your GPU water block comes with un-cuted thermal pads to cover all

the VRM components, such as COILs, MOSFETs, and drivers. Please

use 1,0mm thick thermal pads which should be placed on the water

block, as illustrated below. EK made sure to provide you with more

than an adequate quantity of thermal pads to complete this Step.

You must remove the protective foil from both sides of the

thermal pad before installation.

Thermal Pad F 1.0 mm

Thermal Grease

Apply the enclosed EK-TIM Ectotherm thermal grease (thermal

compound) on the GPU heat spreader – IHS – as shown in the

image. The layer of the thermal compound must be thin and even

over the entire surface of the IHS.

The excessive or uneven application of thermal grease

may lead to poor performance!

APPLYING THERMAL COMPOUND

For this Step, you will need:

- 9 -

INSTALLING THE WATER BLOCK

STEP 1

PLACING THE BLOCK ON THE GRAPHICS CARD

This procedure is the same for all full-cover water blocks. Carefully

position the water block with preinstalled standoffs on the graphics

card. During this process, make sure you have aligned mounting

holes of the PCB with holes of the water block.

Pay attention not to use too much force when pressing

the block down to the PCB since chip dies are prone

to cracking.

STEP 1

For this Step, you will need:

M 2.5 PVC Washer

(8 pcs)

M2.5 x 4 AX1

Screw (8 pcs)

4 mm

STEP 2

ATTACHING THE WATER BLOCK

Use eight (8) M2.5 x 4 AX1 screws and M2.5 PVC washers.

Tighten the screws evenly using the Phillips head screwdriver. EK

recommends you start tightening the screws around the GPU core

ﬁrst and then continuing outward to prevent damage to the GPU.

The screws must be present on the places marked below:

Phillips Head

Screwdriver

- 10 -

STEP 3

Use stock cross backplate from the original card and mount it with

original stock M3 screws.

STEP 4bSTEP 4a

STEP 4

Secure power cable with mounting it into included inox power

adapter.

STEP 4a

Stick the two included plastics pads (M3) on to inox power addapter

as shown on picture.

STEP 4b

Insert 8-pin power connector in to the inox adapter. Pads on the

power adapter must be alligned with openings in inox power adapter.

Pay attention to the orietation of the latch on connector.

Inhaltsverzeichnis

Andere ekwb Zubehör Handbücher

ekwb

ekwb EK-FC980 GTX TF5 R2.0 Backplate Leitfaden

ekwb

ekwb EK-FB KIT GA-X99 Handbuch

ekwb

ekwb EK-FC1080 GTX Strix Bedienungsanleitung

ekwb

ekwb EK-FB MSI X299M GAMING PRO CARBON RGB... Bedienungsanleitung

ekwb

ekwb EK-FC980 GTX WF3 Backplate Leitfaden

ekwb

ekwb EK-FC1080 GTX Ti Strix RGB Bedienungsanleitung

ekwb

ekwb EK-Momentum ROG Strix Z390I RGB Bedienungsanleitung

ekwb

ekwb EK-FC1070/1080 GTX Bedienungsanleitung

ekwb

ekwb EK-Momentum MSI Z390 MEG ACE Bedienungsanleitung

ekwb

ekwb EK-Vector Strix RTX 2070 RGB Bedienungsanleitung

ekwb

ekwb EK-FB ASUS Maximus XI EXTREME Bedienungsanleitung

ekwb

ekwb EK-FB ASUS MAXIMUS III FORMULA Leitfaden

ekwb

ekwb EK-FC980 GTX Strix Backplate Leitfaden

ekwb

ekwb EK-FB ASUS Maximus XI HERO Bedienungsanleitung

ekwb

ekwb EK-FB ASUS CROSSHAIR V Leitfaden

ekwb

ekwb EK-Velocity WS Series Bedienungsanleitung

ekwb

ekwb EK-FC780 GTX Ti Handbuch

ekwb

ekwb EK-FC970 GTX Strix Backplate Leitfaden

ekwb

ekwb EK-FB ASUS X399 GAMING RGB Monoblock Bedienungsanleitung

ekwb

ekwb EK-Vector RTX Aorus 2080 Bedienungsanleitung

ekwb

ekwb EK-FC1080 GTX TF6 Bedienungsanleitung

ekwb

ekwb EK-FC1080 GTX Ti FTW3 Bedienungsanleitung

ekwb

ekwb EK-FB ASUS Z270I/Z370I Strix Monoblock Bedienungsanleitung

ekwb

ekwb EK-FB ASUS Z270/Z370 Strix Monoblock Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

ekwb EK-PRO GPU WB RTX A100 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken