Ekwb EK-FC470 GTX Handbuch

All disclosures, notices and warranty conditions are being written on the back of the box. Released on 13th of April, 2010.

Installation and mounting manual for EK-FC470 GTX water block

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the

liquid seal is made using o-rings.

STEP 1: GENERAL INFORMATION. Sample picture of NVidia GeForce 470 GTX PCB design

STEP 2: PREPARING YOUR GRAPHIC

CARD.

1. REMOVING STOCK COOLER: Remove

encircled screws on the bracket:

STEP 2 cont.: PREPARING YOUR GRAPHIC CARD

1 cont.. REMOVING STOCK COOLER. Remove all encircled screws. All heat sink assembly

screws and backplate should be removed. There are 16 screws on the back of the graphic

card.

2. CLEANING THE PCB. Carefully detach the original heat sink after removing all

fasteners securing it to the board and bracket. Wipe off the remains (by using

non–abrasive cloth or Q-tip, as shown on sample photo) of the original thermal

compound until the components and circuit board are completely clean. EKWB

does not recommend using any liquids for removing paste.

3. APPLYING THERMAL COMPOUND

Apply thermal compound: lightly coat the GPU with for example Arctic Cooling MX2 ™ or

MX3 ™ thermal compound. Follow this link:

http://www.arctic-cooling.com/catalog/images/install_mx2_retail.pdf for detailed

instructions. EKWB recommends to apply thermal grease in cross form for best performance

(see sample picture).

4. CUTTING THERMAL PADS. Your block comes with thermal pads, which have to

be placed on chips (PLEASE REMOVE FOIL ON BOTH SIDES OF THERMAL PADS

PRIOR TO INSTALLATION. WARNING: DIMENSION BELLOW ARE SCALED.) All

thermal pads are 1mm thick. Thermal pads #1 need to be cut to 4 pieces for

RAM modules.

STEP 3: INSTALLING WATER BLOCK

1. PLACING THERMAL PADS ON PCB. Place thermal pads on chips so that numbers

on chips match size of thermal pads. Thermal pad number 1 & 2 will have to be cut

by user to match all small mosfet chips (EKWB made sure users have more than

enough pads to cover all surfaces that need to be covered to make block fully

function). You can also use small drop of thermal grease on chips to make thermal

pads more adhesive.

2. PLACING GPU REINFORCE PLATE ON PCB. Place metal reinforcer and

reinforce washer on PCB as shown on picture below and screw it in with

enclosed M3x4 screws. Make sure you use fasten screws equally and do

not use too much force.

Orientation

of reinforce

is important!

1 1 1 1

Washer

All disclosures, notices and warranty conditions are being written on the back of the box. Released on 13th of April, 2010.

3. PLACING STANDOFFS ON BLOCK. Standoffs (thickness 3,9mm) are obligatory to

make this block fully functional and safe mounting. Please use small amount of

thermal grease on standoffs and glue them so they are concentric with mounting

holes. Once they are stuck to block be careful not to move them.

4. ATTACHING BLOCK TO GRAPHIC CARD. By using Philips screwdriver screw in

enclosed M3x8 screws. EKWB recommends start screwing the screws around the

GPU core and continue outwards.

STEP 4: CHECKING FOR CONTACTS

Temporarily r

emove the water block to check for uniform surface contact between the block and the components. Note the pattern of contact on a piece of paper. Then repeat

substeps in previous section to reattach the block. In case you can’t get good contact, please check again your thermal pad thickness our contact our support service.

STEP 5: POSITIONING FITTINGS

Please use spacer only on copper base if you use fitting with G1/4 thread longer than 5mm (see sample picture). Screw in the fittings and plugs (please use spacers only on

copper base for fittings). Use 6mm Allen key to screw in and tighten new EK-Plug G1/4. Attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit.

EKWB recommends using high flow fittings with the EK-FC 470 GTX series water blocks. To ensure that the tubes are securely attached to the barb/fittings, please use hose

clamps or an appropriate substitute. The use of an algaecide is always recommended for any liquid cooling system.

You can use any hole as an inlet/outlet hole.

STEP 6: INSERTING CARD IN YOUR PC CASE

Carefully lift your card with installed block and insert it in your PC case. Please bear in mind that your card suddenly withstands extra weight thus again be very careful not to

bend it or cause any other unneeded moves that might damage your card or block during installation.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver 10 x screws M3x8 DIN7985 4 x M3x4 DIN7985

Fitting

Gasket/O-ring

G1/4

Spacer

Plug

Use 10 screws M3x8

Plug

6mm Allen key

Dieses Handbuch passt für folgende Modelle

Andere ekwb Computerhardware Handbücher

ekwb

ekwb EK-FB ASUS PRIME X299 RGB Monoblock Bedienungsanleitung

ekwb

ekwb EK-Quantum Reaction AIO RX 6800/6900 D-RGB P240 - AMD Radeon... Bedienungsanleitung

ekwb

ekwb EK-Quantum Vector FTW3 RTX 3070 Bedienungsanleitung

ekwb

ekwb EK-Quantum Vector RE RTX 3080 Active Backplate... Bedienungsanleitung

ekwb

ekwb EK-FC1080 GTX Ti Aorus RGB Bedienungsanleitung

ekwb

ekwb EK-Classic 115 D-RGB Series Bedienungsanleitung

ekwb

ekwb EK-FB KIT ASUS R5-E10 Leitfaden

ekwb

ekwb EK-Quantum Reflection2 PC-O11D EVO D5 PWM... Bedienungsanleitung

ekwb

ekwb EK-FC Strix RTX 2080 Ti Backplate Classic Bedienungsanleitung

ekwb

ekwb EK-FB ASUS Max4 Extreme Leitfaden

ekwb

ekwb EK-FC Titan X Original CSQ Handbuch

ekwb

ekwb EK-Quantum Kinetic TBE DDC PWM Series Bedienungsanleitung

ekwb

ekwb EK-FB KIT GA-X99 SOC Champion Series Handbuch

ekwb

ekwb SLIM 120 Bedienungsanleitung

ekwb

ekwb EK-FC970 GTX ACX Series Handbuch

ekwb

ekwb EK-FC R9-390X TF5 Series Handbuch

ekwb

ekwb EK-PRO GPU WB RTX 6000 ADA Nickel Inox Bedienungsanleitung

ekwb

ekwb EK-Quantum Vector Aorus RTX 2080 D-RGB Bedienungsanleitung

ekwb

ekwb EK-FC780 GTX HOF Series Handbuch

ekwb

ekwb EK-FC R9 290X DCII Leitfaden

ekwb

ekwb EK-FC 5870 MSI Handbuch

ekwb

ekwb EK-FC1080 GTX JetStream Bedienungsanleitung

ekwb

ekwb EK-FC R9-290X Lightning Series Handbuch

ekwb

ekwb EK-FC R9-295X2 Leitfaden

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung

ekwb EK-FC470 GTX Handbuch

Beliebte Computerhardware Handbücher anderer Marken