Elation DESIGN PROMO 360 Bedienungsanleitung

DESIGN PROMO 360

USER MANUAL

For your own safety, please read this user manual carefully before installing the device.

Keepthisdeviceaway from rainand moisture!

Unplugmainsleadbeforeopeningthehousing.

Every person involved with the installation, operation and maintenance of this device has to:

-be qualified

-follow carefully the instructions of this manual

INTRODUCTION:

Thank you for having chosen this professional advertisement lighting.

You will see you have acquired a powerful and versatile device.

Unpack the device. Inside the box you should find:

1. The fixture device

2. A power cable

3. An XLR connection cable

4. A safety cable and this manual

Please check carefully that there is no damage caused by transportation. Should there be any, consult your dealer

and don’t install this device.

Features:

·16 bit resolution

·Movement: 540°/630° optional

·For smooth and precise resolution

·Can rotate continuously

·While Channel 4 on DMX value 0-63 , channel 1,2,3 can do 16 bit high resolution movement

·While Channel 4 on DMX value 64-127, the base rotates continuously in clockwise direction

·While Channel 4 on DMX value 128-191, the base rotated continuously in counterclockwise direction

·While Channel 4 on DMX value 236-245 , reset after 8 seconds

SAFETY INSTRUCTIONS

Becarefulwithyouroperations.Withadangerousvoltageyoucan

Suffera dangerouselectricshockwhentouchingwires!

This device has left the factory in perfect condition. In order to maintain this condition and to ensure

a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning

notes written in this user manual.

- １- XM080-V1.0 NR

If the device has been exposed to temperature changes due to environmental changes, do not switch

it on immediately. The arising condensation could damage the device. Leave the device switched off

until it has reached room temperature.

If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by

the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.

This device falls under protection-class I. Therefore it is essential that the device be earthed.

The electric connection must carry out by qualified person.

Make sure that the available voltage is not higher than stated at the end of this manual.

Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case,

replacement of the cable must be done by an authorized dealer.

Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle

the power cord by the plug. Never pull out the plug by tugging the power cord.

During initial start-up some smoke or smell may arise. This is a normal process and does not

necessarily mean that the device is defective, it should decrease gradually.

Never touch the device during operation!

The housing may heat up

CAUTION!

Please be aware that damages caused by manual modifications to the device are not subject to

warranty. Keep away from children and non-professionals.

GENERAL GUIDELINES

This device is a lighting effect for professional use on stages, in discotheques, theatres, etc.

This fixture is only allowed to be operated with the max alternating current which stated in the

technical specifications in the last page of this manual, the device was designed for indoor use only.

Lighting effects are not designed for permanent operation. Consistent operation breaks may ensure

that the device will serve you for a long time without defects. Do not shake the device.

Avoid brute force when installing or operating the device.

While choosing the installation-spot, please make sure that the device is not exposed to extreme heat,

moisture or dust. The minimum distance between light-output from the projector

Always fix the fixture with an appropriate safety cable if you use the clamp to hang up the fixture.

When fixing the device on a raised-from-the- ground support, be sure to use no less than screws and

nuts of M10 x 25 mm and insert them in the pre-arranged screw holes in the base of the fixture.

If you use the quick lock cam in hanging up the fixture, please make sure the 4 quick lock fasteners

turned in the quick lock holes correctly.

Operate the device only after having familiarized with its functions. Do not permit operation by

persons not qualified for operating the device. Most damages are the result of unprofessional

- ２- XM080-V1.0 NR

operation.

Please use the original packaging if the device is to be transported.

For safety reasons, please be aware that all modifications on the device are forbidden.

If this device will be operated in any way different to the one described in this manual, the product

may suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to

short-circuit, burns, electric shock, lamp explosion, crash, etc.

INSTALLATION INSTRUCTIONS

Mounting the device

Please consider the EN 60598-2-17 and the other respective national norms durin

the

installation. The installation must only be carried out by a qualified person.

The installation of the effect has to be built and constructed in a way that it can hold 10 times the

weight for 1 hour without any harming deformation.

The installation must always be secured with a secondary safety attachment, e.g. an appropriate

safety cable.

Never stand directly below the device when mounting, removing or servicing the fixture.

The operator has to make sure the safety relating and machine technical installations are approved by

an expert before taking the device into operation for the first time.

These installations have to be approved by a skilled person once a year.

Before taking into operation for the first time,

the installation has to be approved by an expert.

Cautions:

The effect should be installed outside areas where persons may reach it, walk by or be seated.

Overhead mounting requires extensive experience, including amongst others calculating

working load limits, installation material being used, and periodic safety inspection of all

installation material and the device. If you lack these qualifications, do not attempt the

installation yourself. Improper installation can result in bodily injury.

The electric connection must only be carried out by a qualified electrician.

Before mounting make sure that the installation area can hold a minimum point load of 10 times the

- ３- XM080-V1.0 NR

device’s weight.

Connect the fixture to the mains with the power plug.

Installation method via clamp

Please refer to the picture below:

(1)Omega-holders

(2)Clamp

(3)Safety-rope

(4)Quick-lock fastener

Screw one clamp each via a M12 screw and nut onto the Omega holders.

Insert the quick-lock fasteners of the first Omega holder into the respective holes on the bottom of

the device. Tighten the quick-lock fasteners fully clockwise. Install the second Omega holder.

Pull the safety-rope through the holes on the bottom of the base and over the trussing system or a

safe fixation spot. Insert the end in the carabine and tighten the safety screw.

DMX-512 control connection

Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other

side to the male 3-pin XLR input of the ad lighting. You can chain multiple ad lighting together

through serial linking. The cable needed should be two core, screened cable with XLR input and output

connectors. Please refer to the diagram below.

DMX-512 connection with DMX terminator

- ４- XM080-V1.0 NR

For installations where the DMX cable has to run a long distance or is in an electrically noisy

environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in

preventing corruption of the digital control signal by electrical noise. The DMX terminator is simply

an XLR plug with a 120 Ωresistor connected between pins 2 and 3,which is then plugged into the

output XLR socket of the last fixture in the chain. Please see illustrations below.

address9 address5 address1

Projector DMX starting address selection

All fixtures should be given a DMX starting address when using a DMX signal, so that the correct

fixture responds to the correct control signals. This digital starting address is the channel number

from which the fixture starts to “listen” to the digital control information sent out from the DMX

controller. The allocation of this starting address is achieved by setting the correct number on the

display located on the base of the device.

You can set the same starting address for all fixtures or a group of fixtures , or make different

address for each fixture individually.

If you set the same address, all the units will start to “listen” to the same control signal from the same

channel number. In other words, changing the settings of one channel will affect all the fixtures

simultaneously.

If you set a different address, each unit will start to “listen” to the channel number you have set,

based on the quantity of control channels of the unit. That means changing the settings of one

channel will affect only the selected fixture.

In the case of the ad lighting, which is a 4 channel fixture, you should set the starting address of the

first unit to 1, the second unit to 5(4 + 1), the third unit to 9 (5+ 4), and so on.

- ５- XM080-V1.0 NR

Note:

The modes of DMX 512 data and lamp are shown via the display:

... .

Lamp on Lamp on

DMX OK DMX OK

NO DMX NO DMX

Lamp off Lampoff

1. After switching on, the device will automatically detect whether DMX 512 data is received or not. If the data is

received, the the display will show "A.001" with the actually set address. If there is no data received at the

DMX-input, the display will flash "A001" with the actually set address.

This situation can occur if:

- the 3 PIN XLR plug (cable with DMX signal from controller) is not connected with the input of the device.

- the controller is switched off or defective, if the cable or connector is defective or the signal wires are swap in the

input connector.

It’s necessary to insert the XLR termination plug (with 120 Ohm) in the last lighting in the link in order to ensure

proper transmission on the DMX data link.

2. If the lamp is on, the the display will show "A00.1" with the actually set address. If the lamp is off, the the

display will show "A001" with the actually set address.

- ６- XM080-V1.0 NR

Control Board

The Control Board offers several features: you can simply set the starting address, switch on and off the lamp, run

the pre-programmed program or make a reset.

The main menu is accessed by pressing the Mode/esc-button until the display starts flashing. Browse through the

menu by pressing the Up-button or Down-button. Press the Enter-button in order to select the desired menu. You

can change the selection by pressing the Up-button or Down-button. Confirm every selection by pressing the

Enter-button. You can leave every mode by pressing the Mode/esc-button . The functions provided are described in

the following sections.

Default settings shaded

VA L U A001~A511 (AXXX) DMX address setting

ADDR SLAV ON/OFF (SLAV) Slave setting

ALON (AU-A) Automatic Run in Stand Alone

AUTO MAST

(

AU-M

)

Automatic Run as Maste

ALON (SO-A) Sound-controlled Run in Stand

Alone

RUN

SOUN

MAST (SO-M) Sound-controlled Run as Master

VA L U D–XX D-00 (DXXX) Display the DMX 512 value of

each channel

RDIS ON/OFF Reverse display

0 MODE

DISP

CLDI ON/OFF Shut off LED display

RPAN ON/OFF Pan Reverse

16BI ON/OFF Switch 16 bit/8 bit

DEGR 630/540 Pan degree select

SPEE LOW/HIGH Pan/Tilt speed mode select

MIC M-XX M-70 Mic sensitivity

AUTO ON/OFF Automatic Run by no DMX

SOUN ON/OFF Sound Run by no DMX

REST Reset

LODA ON/OFF Restore factory settings

1 SET

VER V-1.0~V-9.9 Software version

MATI 0000~9999(hours) Fixture running time

2 TIME CLMT ON/OFF Clear fixture time

STEP S–01 ~S–48 Steps of Program Run

REC. RE.XX Auto Save Scene

C–01~C–30 0 1 XX(00~FFH)

3 0 XX(00~FFH) Edit the channels of each scene

TIME T XXX(001~999) Time for each scene

3 EDIT

SC01

~ SC48

CNIN ON/OFF Edit program via controller

Note:

By default setting, the lamp is not ignited with power on. Lamp can be turned on via DMX controller.

- ７- XM080-V1.0 NR

Main functions

- Main menu 0

1. Press [MODE/ESC] to enter the main menu "MODE" (display flashing)

2. Press [ENTER] and select "ADDR", “RUN” or "DISP" by pressing [UP] or [DOWN] button.

3. Press [ENTER] for selecting the desired sub menu.

- DMX address setting, Slave setting

- DMX address setting

With this function, you can adjust the desired DMX-address via the Control Board.

1. Select “VALU“ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows “AXXX”,“XXX” stands for the DMX address from 001 to 511.

3. adjust the DMX address by pressing [UP] or [DOWN] button.

4. Press [ENTER] to confirm or pressing [MODE/ESC] to return to main menu.

- Slave setting

With this function, you can define the device as slave.

1. Select “SLAV” by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows “ON” or “OFF”.

3. Press [UP] to select “ON” if you wish to enable this function or press [DOWN] to select “OFF” if you don’t.

4. Press [ENTER] to confirm or press [MODE/ESC] to return to main menu.

- Program Run, Master setting

With the function "RUN", you can run the internal program. You can set the number of steps under Step. You can

edit the individual scenes under Edit. You can run the individual scenes either automatically (AUTO), i.e. with the

adjusted Step-Time or sound-controlled (SOUN). The selection "ALON" means Stand Alone-mode and "MAST"

that the device is defined as master.

- ８- XM080-V1.0 NR

1. Select "AUTO" or "SOUN" by pressing [UP] or [DOWN] button.

2. Press [ENTER] for selecting the desired extension menu.

4. Select "ALON" or "MAST" by pressing [UP] or [DOWN] button.

5. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Display the DMX-value, Reverse display, Shut off LED display

- Display the DMX 512 value of each channel

With this function you can display the DMX 512 value of each channel.

1. Select "VALU" by pressing [UP] or [DOWN] button.

2. Press [ENTER] to confirm; the display shows“D-00”. In this setting, the DMX-adjustment of every channel

will be displayed.

3. The display shows "D-XX, “XX” stands for the DMX-value of the selected channel,Press [UP] or [DOWN]

button in order to select the desired channel. If you select “D-14” the display will only show the DMX-value

of the 14th channel.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Reverse display

With this function you can rotate the display by 180°.

1. Select "RDIS" by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows “ON” or “OFF”.

3. Press [UP] to select “ON” if you wish to enable this function or press [DOWN] button to “OFF” if you

don’t; the display will rotate by 180°.

4. Press[ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Shut off LED display

With this function you can shut off the LED display after 2 minutes.

1. Select "CLDI" by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows “ON” or “OFF”.

3. Press [UP] to select “ON” if you wish to enable this function or press [DOWN] button to “OFF” if you don’t.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- ９- XM080-V1.0 NR

Inhaltsverzeichnis

Andere Elation Scheinwerfer Handbücher

Elation

Elation Arena Par CW Bedienungsanleitung

Elation

Elation DLED 12 BRICK Bedienungsanleitung

Elation

Elation Color Tone 50 Montageanleitung

Elation

Elation ELARQUADBAR Bedienungsanleitung

Elation

Elation Waterfall 250 Bedienungsanleitung

Elation

Elation ARENA PAR ZOOM Bedienungsanleitung

Elation

Elation PAR56 Bedienungsanleitung

Elation

Elation DESIGN SPOT 575E Bedienungsanleitung

Elation

Elation Design LED 108IP Bedienungsanleitung

Elation

Elation KL FRESNEL 4 Bedienungsanleitung

Elation

Elation CUEPIX BLINDER WW2 Bedienungsanleitung

Elation

Elation Design LED 108IP Bedienungsanleitung

Elation

Elation PROTEUS LUCIUS PRL546 Bedienungsanleitung

Elation

Elation VISION 575 Bedienungsanleitung

Elation

Elation Opti 30 RGB Bedienungsanleitung

Elation

Elation PALADIN Bedienungsanleitung

Elation

Elation Design LED 36MH Bedienungsanleitung

Elation

Elation Waterfall 250 Bedienungsanleitung

Elation

Elation Event Brick W System Bedienungsanleitung

Elation

Elation Design LED 72MKII Bedienungsanleitung

Elation

Elation SIXPAR 300IP Bedienungsanleitung

Elation

Elation POWER SPOT 700CMY II Bedienungsanleitung

Elation

Elation KLF832 Bedienungsanleitung

Elation

Elation EVC MH LED Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung