Elation DLED 12 BRICK Bedienungsanleitung
PROFESSIONAL HIGH POWER LED USER’S MANUAL
DLED 12 BRICK
KEEPTHIS MANUAL FOR FUTURE NEEDS
For your own safety, please read this user manual carefully before you initial start-up.
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
Every person involved with the installation, operation and maintenance of this
device has to
- be qualified
- follow the instructions of this manual
- consider this manual to be part of the total product
- keep this manual for the entire service life of the product
- pass this manual on to every further owner or user of the product
- download the latest version of the user manual from the Internet
INTRODUCTION:
Thank you for having chosen this professional LED lighting.
You will see you have acquired a powerful and versatile device.
Unpack the device. Inside the box you should find:
1. The fixture device
2. Two power cable
3. An XLR connection cable
4. A safety cable and this manual
Please check carefully that there is no damage caused by transportation. Should
there be any, consult your dealer and don’t install this device.
-2- V1.0 01NR
SAFETY INSTRUCTIONS
CAUTION
Be very careful during installation. Since you will be working with a dangerous
voltage you can suffer a life-threatening electric shock when touching live wires.
This device has left the factory in perfect condition. In order to maintain this
condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this user manual.
If the device has been exposed to temperature changes due to environmental
changes, do not switch it on immediately. The arising condensation could damage
the device. Leave the device switched off until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device
should be earthed.
The electric connection must carry out by qualified person.
If the external flexible cable or cord of this luminaire is damaged, it shall be
exclusively replaced by the manufacturer or his service agent or a similar qualified
person in order to avoid a hazard.
Make sure that the available voltage is not higher than stated at the end of this
manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this
would be the case, replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning
-3- V1.0 01NR
it. Only handle the power cord by the plug. Never pull out the plug by tugging the
power cord.
During initial start-up some smoke or smell may arise. This is a normal process and
does not necessarily mean that the device is defective, it should decrease gradually.
CAUTION
Never touch the device during operation!
The housing may heat up
CAUTION
Never look directly into the light source,
as sensitive persons may suffer an epileptic shock.
Please be aware that damages caused by manual modifications to the device are not
subject to warranty. Keep away from children and non-professionals.
warran
Important:
Damages caused by the disregard of this user manual are not subject to
ty. The dealer will not accept liability for any resulting defects or problems.
-4- V1.0 01NR
DESCRIPTION OF THE DEVICE
1 W high power LEDS: 4 x red, 4 x blue, 4 x green.
sumption
ptional: 6 channels, 12 channels or 15
d can be controlled independently(15 channels Mode)
ors leds
ed can be selected
Features
·With 12 x
·100 000 hours LED life
·Extremely low power con
·Control signal: Standard DMX-512
·Three DMX control channel modes o
channels
·Each Le
·Stepless RGB colour changing, brilliant color effect
·Strobe effect with 1-18 flashes per second
·General dimming and blackout for all 3 col
·8 built -In programs
·Different running spe
-5- V1.0 01NR
Overview
8:Power output
9:Power input / Fuse holder
10:Safety eyelet
11:DMX-Out socket
12:DMX-In socket
1:Fixation screw
2:Floor-stand
3:Mounting bracket
4:Housing
5:LEDs
6:DIP-switches
7:Power switch
-6- V1.0 01NR
DMX-512 control connection
Connect the provided XLR cable to the female 3-pin XLR output of your controller
and the other side to the male 3-pin XLR input of the LED lighting. You can chain
multiple
LED lighting together through serial linking. The cable needed should be two core,
screened cable with XLR input and output connectors. Please refer to the diagram
below.
DMX-512 connection with DMX terminator
For installations where the DMX cable has to run a long distance or is in an
electrically noisy environment, such as in a discotheque, it is recommended to use
a DMX terminator. This helps in preventing corruption of the digital control signal
by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω
resistor connected between pins 2 and 3,which is then plugged into the output XLR
socket of the last fixture in the chain. Please see illustrations below.
-7- V1.0 01NR
Address13 Address7 Address1
Please note: to ensure maximal stability, only ten devices may be
connected together in this manner! From the 11th devices, please
connect to power supply to get power for the second link.
Installation
Screw the bolt of the clamp into the hold of the bracket, and tighten the screw underneath.
Pull the safety-rope through the holes on the bracket of the base and over the trussing system or a
safe fixation spot. Insert the end in the carabine and tighten the safety screw.
-8- V1.0 01NR
Rigging
The device can be placed directly on the stage floor or rigged in any orientation on
a truss without altering its operation characteristics.
Connecting two DLED 12 BRICK LED-Bar
You can connect two DLED 12 BRICK LED- Bars together by using the mounting
set included in the delivery (see graphic).
Please note: to ensure maximal stability, only four devices may be
connected together in this manner!
-9- V1.0 01NR
OPERATION
1.DMX control Mode:
There is 3 different DMX operation modes available by different settings of
Dip #11 and Dip #12:
( Table 1)
DMX
operation
mode
DIP#
11
DIP#
12
LED control Mode LEDs
control
channels
Preset
programs
channel
Strobe
channel
Master
dimming/pro
gram speed
15CH OFF OFF Each Led can be run individually 1~12 13 14 15
12CH ON OFF Each Led can be run individually 1~12
6CH OFF ON R, G, B run by group 1~3 4 5 6
DMX values of preset programs channel:
0—10 No function
11—40 Preset program 1
41---70 Preset program 2
71---100 Preset program 3
101---130 Preset program 4
131—160 Preset program 5
161—190 Preset program 6
191—220 Preset program 7
221----255 Preset program 8
DMX values of Strobe channel：
0 Open
1----95 Strobe effect slow to fast
96----127 Open
128—159 Pulse Strobe slow to fast
160—191 Open
192----223 Random strobe slow to fast 224—255 Open
Master dimming / Program speed channel:
-10- V1.0 01NR
Inhaltsverzeichnis
Andere Elation Scheinwerfer Handbücher
Elation
Elation Design LED 72MKII Bedienungsanleitung
Elation
Elation VISION 575 Bedienungsanleitung
Elation
Elation KLF832 Bedienungsanleitung
Elation
Elation Color Tone 50 Montageanleitung
Elation
Elation Active Scan 250 Bedienungsanleitung
Elation
Elation WW PROFILE Bedienungsanleitung
Elation
Elation Opti 30 RGB Bedienungsanleitung
Elation
Elation ACL 360 MATRIX Bedienungsanleitung
Elation
Elation Professional SIXPAR 200IP Bedienungsanleitung
Elation
Elation Design LED 36MH Bedienungsanleitung
Elation
Elation EVENT BAR Bedienungsanleitung
Elation
Elation Proteus Brutus Bedienungsanleitung
Elation
Elation ELAR EXFLOOD Bedienungsanleitung
Elation
Elation ProTron LED Bedienungsanleitung
Elation
Elation VISION 250 Bedienungsanleitung
Elation
Elation TVL2000 II Bedienungsanleitung
Elation
Elation Waterfall 250 Bedienungsanleitung
Elation
Elation POWER SPOT 700CMY II Bedienungsanleitung
Elation
Elation ELED DW PAR56 Bedienungsanleitung
Elation
Elation ACL PAR 200 Bedienungsanleitung
Beliebte Scheinwerfer Handbücher anderer Marken
VIZULO
VIZULO Micro Martin Benutzerhandbuch
EuroLite
EuroLite LED IP FL-100 SMD Bedienungsanleitung
Cooper Wheelock
Cooper Wheelock XB12 Bedienungsanleitung
Allen + Roth
Allen + Roth 17624-000 Bedienungsanleitung
ADJ
ADJ 4 STAGE PAK Bedienungsanleitung
Cooper Lighting
Cooper Lighting EGL91SW233 Bedienungsanleitung
