Elation DESIGN SPOT 575E Bedienungsanleitung

Rev. 06/06/2008

Design Wash 575E

Elation Professional

6122 S. Eastern Ave.

Los Angeles, CA. 90040

www.elationlighting.com

Design Wash 575E™

©Elation Professional® 2 Design Wash 575E™

Contents

1. General Information……………………………………………………………………… 3

a. Introduction………………………………………………………………………. 3

b. Unpacking………………………………………………………..…………..… 3

c. Customer Support…………………………………………….………………… 3

d. Warranty Registration……………………………………………………..…… 4

e. Discharge Lamp Warning……………………………………………………… 4

2. Safety Instructions………………………………………………………........…………. 6

3. Features……………………………………………………………………………………8

4. General Guidelines………………………………………………………………………. 9

5. Lamp Installation…………………………………………………………………………. 10

a. Lamp installation…………………………………………………….………….. 10

b. Lamp optimization……………………………………………………..………… 11

6. Mounting and Installation………………………………………………………….……. 13

a. Mounting Positions……………………………………………………………… 13

b. Mounting Points…………………………………………………………………. 14

c. Securing………………………………………………………………………….. 15

7. Understanding DMX……………………………………………………………………... 16

a. DMX Connections………………………………………………………………. 16

b. DMX Terminator…………………………………………………………………. 17

c. 3-Pin to 5-Pin Conversion………………………………………………………. 18

8. Fixture Menu……………………………………………………………………………… 19

a. Menu functions………………………………………………………………….. 21

9. Operation…………………………………………………………………………………..29

10. DMX Channel Traits…………………………………………………………………….. 32

a) DMX Channel Values……………………………………………………………… 33

11. FUSE Replacement………………………………………………………………………. 36

12. Error Codes………………………………………………………………………………. 37

13. Cleaning and Maintenance……………………………………………………………… 40

14. Warranty…………………………………………………………………………………... 41

15. Photometric Data………………………………………………………………………… 43

16. Dimensional Drawings………………………………………………….……………….. 44

17. Circuit Schematic………...………………………………………………………………. 45

18. Technical Specifications…………………………………………...………….………… 47

Design Wash 575E™

©Elation Professional® 3 Design Wash 575E™

1. GENERAL INFORMATION

INTRODUCTION: Congratulations, you have just purchased one of the most innovative and

reliable lighting fixtures on the market today! The Design Wash 575E™ has been designed

to perform reliably for years when the guidelines in this booklet are followed. Please read

and understand the instructions in this manual carefully and thoroughly before attempting to

operate this unit. These instructions contain important information regarding safety during

use and maintenance.

UNPACKING: Thank you for purchasing the Design Wash 575E™ by Elation Professional®.

Every Design Wash 575E™ has been thoroughly tested and has been shipped in perfect

operating condition. Carefully check the shipping carton for damage that may have occurred

during shipping. If the carton appears to be damaged, carefully inspect your unit for damage

and be sure all accessories necessary to operate the unit have arrived intact. In the event

damage has been found or parts are missing, please contact our customer support team for

further instructions. Please do not return this unit to your dealer without first contacting

customer support at the number listed below.

CUSTOMER SUPPORT: Elation Professional®provides a customer support line, to provide

set up help and to answer any question should you encounter problems during your set up

or initial operation. You may also visit us on the web at www.elationlighting.com for any

comments or suggestions. For service related issue please contact Elation Professional®.

Service Hours are Monday through Friday 8:00 a.m. to 5:00 p.m. Pacific Standard Time.

Voice: (323) 582-3322

Fax: (323) 832-9142

E-mail: [email protected]

Forum: www.ElationLighting.com/forum

Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to

rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs

yourself, doing so will void your manufactures warranty.

Design Wash 575E™

©Elation Professional® 4 Design Wash 575E™

Please do not discard the shipping carton in the trash. Please recycle whenever possible.

WARRANTY REGISTRATION: The Design Wash 575E™ carries a two year (730 days)

limited warranty. Please fill out the enclosed warranty card to validate your purchase. All

returned service items whether under warranty or not, must be freight pre-paid and

accompany a return authorization (R.A.) number. The R.A. number must be clearly written

on the outside of the return package. A brief description of the problem as well as the R.A.

number must also be written down on a piece of paper and included in the shipping

container. If the unit is under warranty, you must provide a copy of your proof of purchase

invoice. Items returned without a R.A. number clearly marked on the outside of the package

will be refused and returned at customer’s expense. You may obtain a R.A. number by

contacting customer support at (323) 582-3322.

DISCHARGE LAMP WARNING: This fixture is fitted with a discharge

lamp, which is highly susceptible to damage if improperly handled.

Never touch the lamp with your bare hands, as the oil from your hands

will shorten lamp life. Also, never move the fixture until the lamp has

had ample time to cool. Remember, lamps are not covered under

warranty conditions.

UV RADIATION: This fixture emits intense UV radiation, which is harmful to the eyes and

skin. The intense luminance of the lamp can cause severe damage to the retina. Never

operate this fixture with the protective covers removed, these covers have been specially

designed to shield against UV radiation.

Epileptic Warning: Those suffering from epilepsy should avoid looking directly into the

lamp at all times.

Avoid switching the fixture on and off repeatedly in short intervals, as this will reduce lamp

life and intensity.

To achieve the intensity associated with discharge lamps, these lamps use a gas sealed in a

high-pressure environment to emit a brilliant output. Due to the high pressure involved with

the construction of the lamp, the lamp may explode during prolonged extensive use. This

Design Wash 575E™

©Elation Professional® 5 Design Wash 575E™

risk is increased with age; added care is encouraged when dealing with older lamps. Thus,

lamp should always be replaced at the end of their recommended duty cycle. Extreme

caution should be used when operated this or any fixture fitted with a gas discharge lamp.

Never open this fixture while in use!

During the initial operation of this fixture, a light smoke or smell may emit from the interior of

the fixture. This is a normal process and is caused by excess paint in the interior of the

casing burning off from the heat associated with the lamp and will decrease gradually over

time.

This device falls under protection-class 1. Therefore it is essential that the device be

grounded properly.

Qualified personnel should perform all electrical connections.

Be sure the available voltage matches the voltage requirements of the unit.

Be sure the power cord is never crimped or damaged. If the power cord is damaged, replace

it immediately with a new one of similar power rating.

Always disconnect from main power before performing any type of service or any cleaning

procedure.

Only handle the power cord by the plug. Never pull out the plug by tugging the wire portion of

the cord.

Please be aware that damages caused by manual modifications to the device are not

subject to warranty.

Design Wash 575E™

©Elation Professional® 6 Design Wash 575E™

2. SAFETY INSTRUCTIONS

The Design Wash 575E™ is an extremely sophisticated piece of

electronic equipment. To guarantee a smooth operation, it is

important to follow the guidelines in this manual. The

manufacturer of this device will not accept responsibility for

damages resulting from the misuse of this fixture due to the

disregard of the information printed in this manual.

1. Always be sure that the fan and the air inlets remain clean and are never blocked.

Allow about 6” (15cm) between this fixture and other devices or a wall to allow for

proper cooling.

2. Never touch the fixture during normal operation. This can cause severe personal

injuries and/or damage to the fixture.

3. Be sure to unplug the DESIGN WASH 575E™ from the power outlet before

performing any service related issues.

4. Lamp Replacement; Allow at least 30 minutes after disconnecting main power

before you open the DESIGN WASH 575E™. To prevent personal injury, never

touch the lamp if you are not absolutely sure it has cooled.

5. Never look directly into the lamp beam. You risk injury to your retina, which may

induce blindness.

6. Be sure to track and record the lamp running time. The lamp should be changed at

the end of the specified lamp life, regardless of lamp output. You may also have to

change the lamp if it shows any deformations or damage. The same is with all

glass components, color filters, lenses and mirrors.

7. For safe operation, follow the Installation guide described in chapter two of this

manual. Operating the DESIGN WASH 575E™ without suited safety aids such as

safety cables or clamps can increase the risk of damage and/or personal injury.

8. Installation should only be performed by qualified and certified personnel.

9. When mounting this fixture, use only the original rigging parts included with this

fixture. Any structural modification will void the original manufactures warranty and

Design Wash 575E™

©Elation Professional® 7 Design Wash 575E™

may increase the risk of damage and/or personal injury.

10. To reduce the risk of fire or shock, do not expose this fixture to rain or moisture.

11. Do not attempt to operate this fixture if the power cord has become damaged or

frayed.

Important Notice: Damages resulting from the disregard of safety and general user

instructions found in this user manual are not subject to any warranty claims.

Design Wash 575E™

©Elation Professional® 8 Design Wash 575E™

3. FEATURES

•Pan 540° or 630˚ (User selectable) / Tilt 265°

•Built-In Macros (color)

•3 operation mode: DMX Controlled, Stand-Alone or Sound Activated

•Color Wheel: 8 colors plus white (including UV filter), with rainbow effect

•CMY Variable Color Mixing

•Easy to Navigate On-Board LCD Menu

•Animation Effect Wheel

•Strobe Effect: 0~10 flashes per second or random strobe

•Bright Phillips Gold MSR 575/2 SA DE Lamp (575w / 7200K / 750Hrs / 43,000Lm)

•Linear Dimmer from 0%~100%

•RDMX (Remote DMX addressing from any DMX console)

•Auto test for all functions

•Motorized Linear Zoom (13˚ ~ 50˚)

•Glass Dichroic Reflector for Even Lamp Output

•USITT DMX-512 Complaint

o16 DMX Channels (16bit Operation)

o14 DMX Channels (8bit Operation)

•8 User Assignable Program Presets - Internal Program: Edit and save programs to

the incorporated EEPROM. Maximum of 48 scenes.

Design Wash 575E™

©Elation Professional® 9 Design Wash 575E™

4. GENERAL GUIDELINES

This fixture is a professional lighting effect designed for use on stage, in nightclubs, in

theatres, etc. Do not attempt operation or installation without a proper knowledge on how to

so.

This fixture was designed for indoor use only.

Consistent operational breaks may ensure that the fixture will function properly for many

years to come.

Do not shake the fixture around. Avoid brute force when installing or operating the device.

While choosing an installation location, please be sure that the fixture will not be exposed to

extreme heat, moisture or dust. The minimum distance between the fixture and a wall or flat

surface should be at least .5 meter (about 1.5ft).

Always install the fixture with an appropriate safety cable. When installing the fixture in a

suspended environment always be to use mounting hardware no less than M10 x 25 mm,

also be sure the hardware is insert in the pre-arranged screw holes in the base of the fixture.

When using the quick release “Omega” cam-lock system, be sure the four quick lock

fasteners are locked in the quick lock holes correctly.

Do not attempt to operate this fixture until you have familiarized yourself with its functions.

Do not permit operation by persons not qualified for operating this type of theatrical fixture,

most damages are the result of operations by nonprofessionals.

Please use the original packaging to transport the fixture in for service.

Design Wash 575E™

©Elation Professional® 10 Design Wash 575E™

5. LAMP INSTALLATION INSTRUCTIONS

For a proper and safe lamp change, please read this chapter carefully and follow all

instructions.

Safety Regulations

•Disconnect the unit’s main power supply.

•Allow the unit to cool for at least 30 minutes before attempting any type of service.

•Before you put the Design Wash 575E™ into operation be sure all covers have

been replaced, otherwise you risk damage to the retina and expose to UV radiation!

•Replace the lamp with an approved replacement type. Be sure to follow all the lamp

handleing procedures included with your new lamp. Never handle the new lamp

with your bare hands, the oils from your skin may damage the lamp. Always replace

with the lamp with a lamp that meets the orginal lamp specification, failure to do so

may damage the unit and will void your manufactures warranty.

Installation Procedure:

1. Set the fixture on a flat surface and remove the four screws labeled “A” “B,” “C,” and

“D” found on the back plate of the head assembly.

2. Gently pull out the lamp/socket assembly to access the lamp.

3. Gently remove the old lamp by grasping it by metal ends.

4. Insert the new lamp securely, locking the lamp in place as illustrated in the diagram

on the next page. Orientate the lamp filler tube towards the backside of the reflector.

Before reassembling the unit, be sure the new lamp is securely seated in the lamp

socket. Always be sure to only use specified lamp types! (MSR 575 SA/2 DE lamp or

equivalent).

Andere Handbücher für DESIGN SPOT 575E

Inhaltsverzeichnis

Andere Elation Scheinwerfer Handbücher

Elation

Elation RAYZOR BEAM 2R Bedienungsanleitung

Elation

Elation PAR56 Bedienungsanleitung

Elation

Elation KL FRESNEL 4 Bedienungsanleitung

Elation

Elation ACL PAR 200 Bedienungsanleitung

Elation

Elation ARENA ZOOM Q7IP Bedienungsanleitung

Elation

Elation DESIGN PROMO 360 Bedienungsanleitung

Elation

Elation ELED DW PAR56 Bedienungsanleitung

Elation

Elation WW PROFILE Bedienungsanleitung

Elation

Elation VISION 575 Bedienungsanleitung

Elation

Elation Waterfall 250 Bedienungsanleitung

Elation

Elation ELAR EX TRIFLOOD HP Bedienungsanleitung

Elation

Elation KLF832 Bedienungsanleitung

Elation

Elation Professional SIXPAR 200IP Bedienungsanleitung

Elation

Elation Design LED 36MH Bedienungsanleitung

Elation

Elation Design LED 108IP Bedienungsanleitung

Elation

Elation ACL 360 MATRIX Bedienungsanleitung

Elation

Elation E Spot Led Bedienungsanleitung

Elation

Elation Arena Par CW Bedienungsanleitung

Elation

Elation TVL2000 II Bedienungsanleitung

Elation

Elation Color Tone 50 Montageanleitung

Elation

Elation VISION 250 Bedienungsanleitung

Elation

Elation DW CHORUS 24 Bedienungsanleitung

Elation

Elation EVENT BAR Bedienungsanleitung

Elation

Elation Waterfall 250 Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung