Elma Instruments FieldSense 2.0 Bedienungsanleitung

Manual

FieldSense 2.0

EAN:5706445111558

FieldSense 2.0

Impact resistant

polycarbonate

base layer

Scratch and scuff

resistant lens

Exposure

Indicator LEDs

Power Indicator

Audio Record Indicator

Low Battery Indicator

On / Off / Record button

introduction

The FieldSENSE 2.0 is the next generation in Personal RF Moni- tors specifically designed for

protecting personnel working near broadcast and telecommunications transmitting antennas from

EMF/RF overexposure.

The FieldSENSE 2.0 measures both E and H fields spanning from 50 MHz to 6 GHz with an

isotropic probe architecture. The probe response is shaped to internationally accepted exposure

safety limits and is designed for both body worn, handheld or remote monitoring applications.

Make sure that the device is within its 2-year calibration cycle and do not use it if it appears to have

been damaged.

Used correctly, it will give an indication of field levels approaching or exceeding associated exposure

limits and is a valuable tool to assist in preventing EMF/RF overexposure.

** NOTE: This device is only to be used by RF trained personnel with a complete understanding of

the risks involved with working with RF and know the necessary precautions to be taken.

Furthermore, only use this device within the limits of the design specifications and ensure that it is

not damaged prior to usage.

Overview

FieldSense 2.0

Climbers harness

attachment bars

Unique barcoded serial number

Heavy duty shock absorbing

elastomer outer layer

Lanyard attachment point

USB connection

Access to batteries

Calibration expiry date

Tripod attachment

•Prior to entering an area where transmitting antennas could be present be sure to switch your

FieldSENSE on.

•Switch the FieldSENSE on by pressing and holding the On/Off button for approximately 1

second.

•The LEDs illuminate in sequence followed by a BEEP. Once on the power indicator will flash.

•Should the battery level below the low battery indicator will illuminate. Replace the batteries

•When the exposure level rises above 50% an audible alarm is sounded.

•When close to or exceeding 100% of the exposure limit, the necessary precautions need to be

taken.

•Once switched on the field strength data logger will record all field values measured. These are

accessible via the PC application available from www.FieldSENSE.com. A micro B male USB

connection will be required.

•Once the FieldSENSE is on, the fall detect & alarm system is armed and in the event of a fall

being detected an alarm will sound which can only be cleared by switching the device off and on

again.

•To ensure that the device is not inadvertently left switched on causing unnecessary drain on the

batteries a timer will switch the unit off after 8 hours.

* Always adhere to the relevant safety regulations pertaining to RF exposure in the country of use.

FieldSense 2.0

Audio recording

indicator

Microphone opening

alongside lens with

Gore-Tex® moisture

protection.

•Once the FieldSENSE is switched on the cumulative exposure from all sources present are stored

as Maximum, E and H percentages together with the associated date and time.

•The values are a percentage of the associated exposure guideline power density, either

referenced to E or H field.

•Accessing these values and synchronizing the date/time of the

•The FieldSENSE 2.0 can also capture voice notes which are paired with the measured data.

•Once the device is on, double tap the power button and the Audio re- cording LED will illuminate.

•Speak directly into the front of the device slowly and clearly for best performance.

•A single press of the button will end the audio recording.

•Voice notes can be downloaded from the FieldSENSE using the program available from

www.fieldsense.com

Fall detection & alarm

•The FieldSENSE 2.0 is equipped with a 3-axis accelerometer which is able to detect if the device

experiences a fall.

•This is immediately active when the device is switched on, and should the device detect a fall of

approximately 2m it will sound an alarm

•The alarm can only be cleared by switching the device off again.

•The goal of this is to immediately draw attention to a climber who may have fallen and may be

unconscious.

•The alarm, if uncleared, will continue until the batteries are exhausted.

FieldSense 2.0

Replacing the batteries

•When the Low Battery Indicator begins to flash, replace the batteries.

•Open the elastomer flap at the bottom of the FieldSENSE revealing the battery lid screws.

•Remove the screws and lid and slide out the old batteries. Dispose of these correctly.

•Insert 2 x new AAA (LR03) batteries.

•Replace the battery lid and retighten the screws.

•Securely close the elastomer cover to ensure the moisture seal remains intact.

*Removing the batteries for an extended period of time will

cause the device to lose time on the internal clock. This is

corrected by plugging it into the USB connection on a PC.

FieldSense 2.0

Specifications

•Frequency range of operation 50MHz - 6 GHz

•Frequency response Shaped (Occupational/Controlled)

- ICNIRP (1998)

- FCC [NCRP] OET65 (1997)

- Canada Safety Code 6 (2015)

- IEEE C95.1 (2005) *(see associated table)

•Sensor polarization Isotropic

•Isotropy * ± 3dB

•Probes 3 orthogonal E and 3 orthogonal H field

•Result type Time-averaged RMS power density

•Calibration interval 2yearly

•CW damage level 26 dB above Standard/ 40 000% of Standard

•Battery type 2 x 1.5V Size AAA(LR03) Alkaline

•Battery life 6 months—1 year (average usage)

•Weight (incl. batteries) 0.25 lb, 115 gr

•Dimensions 146 x 26 x 42mm

•IEC 60529 rating IP64 (battery cap closed)

•Temperature range -20°C to 50 °C

•Fall detection 3 axis accelerometer

*Isotropy is the measure of deviation from the mean over the sphere at a frequency.

Frequency response1

Frequency ICNIRP FCC/NCRP Canada SC6

50—80 0.5 ± 3.5 dB 0.5 ± 3.5 dB -1.5 ± 3.5 dB

80—400 2.0 ± 3.0 dB 2.0 ± 3.0 dB 0.5 ± 3.5 dB

400—700 1.3 ± 2.3 dB 2.9 ± 2.1 dB 1.3 ± 2.3 dB

700—3000 0.3 ± 3.2 dB 1.2 ± 3.8 dB -1.0 ± 4.0 dB

3000—6000 0.0 ± 3.5 dB 0.0 ± 3.5 dB -1.5 ± 2.5 dB

1. The response is a combined E & H field deviation from the relevant standard including the isotropy

as is reported by the LED indicators.

2. Positive values indicate conservative readings i.e. early warning.

3. NB! Only use the device in this frequency range, measurements outside of this frequency range will

not be accurate and cannot be guaranteed

4. H field contributions assessed from 50MHz —1 GHz only.

5. Not suitable for Radar applications.

FieldSense 2.0

Calibration certificate

Alphawave Products (Pty) Ltd hereby certifies

that the performance of this unit has been

verified to be within operating specifications.

Serial Number:

Calibration Date:

Valid for 24 months

QA Approved

field SENSE

email [email protected] tel + 27 21 880 1880 (INTL)

web www.fieldsense.com + 1 312 260 6055 (US/CA)

+ 61 8 9381 7199 (AU/NZ)

FieldSense 2.0

v.20140114-01-2020 14:34:32

Regulatory compliance

CE Compliance for Europe

The manufacturer, EMSS Consulting (Pty) Ltd, hereby declares that Field- SENSE 2.0 complies

with the essential requirements of the following Directives; 2012/19/EU-Waste Electrical and

Electronic Equipment; 2011/65/EU- Restriction of the use of Hazardous Substances;

2014/30/EU- Electromagnetic compatibility; 2001/95/EC-General Product Safety Directive

through conformity to IEC 61000-6-4; IEC 6100-6-2; IEC 62368-1.

FCC regulatory information for the USA

This device complies with part 15 of the FCC Rules: Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause

undesired operation.

Any changes or modifications not expressly approved by the manufacturer could void the user's

authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own

expense.

CSA regulatory information for Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB -003 du Canada.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Elma Instruments Messgerät Handbücher

Elma Instruments

Elma Instruments HT9 Bedienungsanleitung

Elma Instruments

Elma Instruments 2500 Bedienungsanleitung

Elma Instruments

Elma Instruments VT-8204 Bedienungsanleitung

Elma Instruments

Elma Instruments BM076 Bedienungsanleitung

Elma Instruments

Elma Instruments ElmaFlex 460 Bedienungsanleitung

Elma Instruments

Elma Instruments 593R Bedienungsanleitung

Elma Instruments

Elma Instruments Systronik S2601 Bedienungsanleitung

Elma Instruments

Elma Instruments DT-802D Bedienungsanleitung

Elma Instruments

Elma Instruments BM869s Bedienungsanleitung

Elma Instruments

Elma Instruments DT902 Bedienungsanleitung

Elma Instruments

Elma Instruments Systronik FT30 Bedienungsanleitung

Elma Instruments

Elma Instruments Kew Mate 2012 Bedienungsanleitung

Elma Instruments

Elma Instruments Elma BM251s Bedienungsanleitung

Elma Instruments

Elma Instruments SwemaFlow 125D Bedienungsanleitung

Elma Instruments

Elma Instruments Elma 9200BT Bedienungsanleitung

Elma Instruments

Elma Instruments SAGAB 981A Bedienungsanleitung

Elma Instruments

Elma Instruments Elma 35 Bedienungsanleitung

Elma Instruments

Elma Instruments ELMA 795 Bedienungsanleitung

Elma Instruments

Elma Instruments Paintcheck FN Bedienungsanleitung

Elma Instruments

Elma Instruments FiberMASTER Bedienungsanleitung

Elma Instruments

Elma Instruments RT606 A Bedienungsanleitung

Elma Instruments

Elma Instruments 3037 Bedienungsanleitung

Elma Instruments

Elma Instruments Elma 92 Bedienungsanleitung

Elma Instruments

Elma Instruments 2500A HandyAmp Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung