Emerson Rosemount 3051SF Series Bedienungsanleitung

Quick Start Guide

00825-0100-4801, Rev NB

December 2018

Rosemount™ 3051S Series Pressure

Transmitter and Rosemount 3051SF

Series Flowmeter

with HART® Protocol

Safety messages

NOTICE

This guide provides basic guidelines for Rosemount™ 3051S Series Pressure Transmitters. It also

provides the basic electronic guidelines for the Rosemount 3051SFA Reference Manual, Rosemount

3051SFC Reference Manual, and Rosemount 3051SFP Reference Manual. It does not provide

instructions for diagnostics, maintenance, service, or troubleshooting. Refer to the Rosemount 3051S

HART Reference Manual for more instruction. This document is also available electronically on

Emerson.com/Rosemount.

WARNING

Explosions could result in death or serious injury.

Installation of device in an explosive environment must be in accordance with appropriate local,

national, and international standards, codes, and practices.

Review the Rosemount 3051S/3051SFx/3051S-ERS Product Certifications section of this guide for any

restrictions associated with a safe installation.

•Before connecting a handheld communicator in an explosive atmosphere, make sure the

instruments in the loop are installed in accordance with intrinsically safe or non-incendive field

wiring practices.

•In an explosion-proof/flameproof installation, do not remove the transmitter covers when power

is applied to the unit.

•Use appropriately rated Ex adaptors, blanking elements, or glands during installation.

•Keep process insulation at least 1 inch (25 mm) from transmitter connection.

Process leaks could result in death or serious injury.

•Install and tighten process connectors before applying pressure.

Electrical shock could cause death or serious injury.

•Avoid contact with the leads and terminals. High voltage that may be present on leads can cause

electrical shock.

Conduit/cable entries

•Unless marked, the conduit/cable entries in the transmitter housing use a ½–14 NPT thread form.

Entries marked “M20” are M20 × 1.5 thread form. On devices with multiple conduit entries, all

entries will have the same thread form. Only use plugs, adapters, glands, or conduit with a

compatible thread form when closing these entries.

•When installing in a hazardous location, use only appropriately listed or Ex certified plugs, glands,

or adapters in cable/conduit entries.

Contents

Mount the transmitter................................... 5

Consider housing rotation............................11

Set switches and jumpers.............................12

Connect wiring and power up...................... 14

Verify configuration..................................... 22

Trim the transmitter.................................... 26

Safety instrumented systems installation.....28

Rosemount 3051S/3051SFx/3051S-ERS

Product Certifications.................................. 29

Quick Start Guide December 2018

2 Rosemount 3051S

Rosemount 3051S Declaration of Conformity

.................................................................... 45

China RoHS.................................................. 49

December 2018 Quick Start Guide

Quick Start Guide 3

Quick Start Guide December 2018

4 Rosemount 3051S

1 Mount the transmitter

1.1 Liquid flow applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Mount the transmitter so that the drain/vent valves are oriented

upward.

A. Direction of flow

1.2 Gas flow applications

Procedure

1. Place taps in the top or side of the line.

2. Mount beside or above the taps.

A. Direction of flow

December 2018 Quick Start Guide

Quick Start Guide 5

1.3 Steam flow applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Fill impulse lines with water.

A. Direction of flow

1.4 Using a mounting bracket

If the transmitter requires the use of a mounting bracket, use the images

below for instructions on how to properly mount the transmitter using the

Emerson™ provided mounting brackets. Use only bolts provided with the

transmitter or sold as Emerson spare parts.

1.5 Bolting considerations

About this task

If the transmitter installation requires assembly of a process flange, manifold,

or flange adapters, follow these assembly guidelines to ensure a tight seal for

optimal performance characteristics of the transmitter. Only use bolts

supplied with the transmitter or sold by Emerson™ as spare parts. Figure 1-1

illustrates common transmitter assemblies with the bolt length required for

proper transmitter assembly.

Quick Start Guide December 2018

6 Rosemount 3051S

Figure 1-1: Common Transmitter Assemblies

4 × 1.75-in.

(44 mm)

4 × 1.75-in.

(44 mm)

4 × 2.25-in.

(57 mm)

4 ×1.75-in.

(44 mm) 4 ×1.50-in.

(38 mm)

4 × 2.88-in.

(73 mm)

A. Transmitter with coplanar flange

B. Transmitter with coplanar flange and optional flange adapters

C. Transmitter with traditional flange and optional flange adapters

D. Transmitter with coplanar flange and optional Rosemount Conventional

Manifold and flange adapters

Note

For all other manifolds, contact Customer Central technical support.

Bolts are typically carbon steel or stainless steel. Confirm the material by

viewing the markings on the head of the bolt and referencing Table 1-1 . If

bolt material is not shown in Table 1-1, contact the local Emerson

representative for more information.

Use the following bolt installation procedure:

Procedure

1. Carbon steel bolts do not require lubrication and the stainless steel

bolts are coated with a lubricant to ease installation. However, no

additional lubricant should be applied when installing either type of

bolt.

2. Finger-tighten the bolts.

3. Torque the bolts to the initial torque value using a crossing pattern.

See Table 1-1 for initial torque value.

4. Torque the bolts to the final torque value using the same crossing

pattern. See Table 1-1 for final torque value.

December 2018 Quick Start Guide

Quick Start Guide 7

5. Verify the flange bolts are protruding through the sensor module

before applying pressure (see Figure 1-2).

Example

Table 1-1: Torque Values for the Flange and Flange Adapter Bolts

Bolt material Head markings Initial torque Final torque

Carbon Steel

(CS)

B7M

300 in-lb 650 in-lb

Stainless Steel

(SST)

316

STM

316

B8M

150 in-lb 300 in-lb

Figure 1-2: Proper Bolt Installation

A. Bolt

B. Sensor module

Quick Start Guide December 2018

8 Rosemount 3051S

1.6 O-rings with flange adapters

WARNING

Failure to install proper flange adapter O-rings may cause process leaks, which

can result in death or serious injury. Only use the O-ring that is designed for its

specific flange adapter.

A. Flange adapter

B. O-ring

C. PTFE-based profile (square)

D. Elastomer profile (round)

Whenever the flange or adapters are removed, visually inspect the O-rings.

Replace them if there are any signs of damage, such as nicks or cuts. If the O-

rings are replaced, re-torque the flange bolts and alignment screws after

installation to compensate for seating of the O-rings.

1.7 In-line gage transmitter orientation

The low side pressure port (atmospheric reference) on the in-line gage

transmitter is located under the sensor module neck label. (See Figure 1-3)

Keep the vent path free of any obstruction, including but not limited to paint,

dust, and lubrication by mounting the transmitter so that any contaminants

can drain away.

December 2018 Quick Start Guide

Quick Start Guide 9

Figure 1-3: In-line Gage Transmitter

A. Low side pressure port (under neck label)

Quick Start Guide December 2018

10 Rosemount 3051S

Andere Handbücher für Rosemount 3051SF Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson Rosemount 3144P Bedienungsanleitung

Emerson

Emerson Rosemount 4600 Bedienungsanleitung

Emerson

Emerson Rosemount FCL-01 Bedienungsanleitung

Emerson

Emerson Rosemount 5081 Bedienungsanleitung

Emerson

Emerson 6081-P Bedienungsanleitung

Emerson

Emerson Rosemount 2051 Bedienungsanleitung

Emerson

Emerson Rosemount 3300 Series Bedienungsanleitung

Emerson

Emerson Micro Motion 3500 Bedienungsanleitung

Emerson

Emerson Micro Motion 5700 Kurzanleitung

Emerson

Emerson Rosemount 3051HT Bedienungsanleitung

Emerson

Emerson Rosemount 5400 Series Bedienungsanleitung

Emerson

Emerson Rosemount 3051 CF Series Bedienungsanleitung

Emerson

Emerson Rosemount 5408 Bedienungsanleitung

Emerson

Emerson Rosemount 1199 Bedienungsanleitung

Emerson

Emerson Rosemount 644 Bedienungsanleitung

Emerson

Emerson Rosemount 148 Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount 5400 Series Bedienungsanleitung

Emerson

Emerson PT5N Series Bedienungsanleitung

Emerson

Emerson Rosemount 326P Bedienungsanleitung

Emerson

Emerson Rosemount 3101 Bedienungsanleitung

Emerson

Emerson Fisher 4200 Series Bedienungsanleitung

Emerson

Emerson Rosemount TCL Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung