Emerson Rosemount 5408 Bedienungsanleitung

Quick Start Guide

00825-0100-4408, Rev AD

March 2018

Rosemount™ 5408 and 5408:SIS Level

Transmitters

Cone Antenna

1 About this guide

This Quick Start Guide provides basic guidelines for the Rosemount 5408 and

5408:SIS Level Transmitters. Refer to the Rosemount 5408 and 5408:SIS

Reference Manual for more instructions. The manual and this guide are also

available electronically on Emerson.com/Rosemount.

WARNING!

Failure to follow safe installation and servicing guidelines could result in

death or serious injury.

•Make sure the transmitter is installed by qualified personnel and in

accordance with applicable code of practice.

•Use the equipment only as specified in this manual. Failure to do so may

impair the protection provided by the equipment.

•For installations in hazardous locations, the transmitter must be installed

according to the Rosemount 5408 and 5408:SIS Product Certifications

document and System Control Drawing (D7000002-885).

Explosions could result in death or serious injury.

•Verify that the operating atmosphere of the transmitter is consistent with

the appropriate hazardous locations certifications.

•Before connecting a Field Communicator in an explosive atmosphere,

ensure the instruments are installed in accordance with intrinsically safe

or non-incendive field wiring practices.

•Do not remove the transmitter cover in explosive atmospheres when the

circuit is live.

•Both transmitter covers must be fully engaged to meet explosion-proof

requirements.

Electrical shock could cause death or serious injury.

•Avoid contact with the leads and terminals. High voltage that may be

present on leads can cause electrical shock.

•Make sure the mains power to the transmitter is off and the lines to any

other external power source are disconnected or not powered while

wiring the transmitter.

Process leaks could result in death or serious injury.

•Make sure that the transmitter is handled carefully. If the process seal is

damaged, gas might escape from the tank.

Quick Start Guide March 2018

2Rosemount 5408 and 5408:SIS Level Transmitters

CAUTION!

Hot surfaces

The flange and process seal may be hot at high process temperatures. Allow

to cool before servicing.

March 2018 Quick Start Guide

Quick Start Guide 3

2 Confirm approval type

For hazardous locations transmitters labeled with multiple approval types:

Permanently mark the checkbox of the selected approval type(s).

Label with Multiple Approval TypesFigure 2-1:

Quick Start Guide March 2018

4Rosemount 5408 and 5408:SIS Level Transmitters

3 Mount the transmitter

3.1 Flanged version

1. If applicable, assemble the segmented cone antenna (see Chapter 9).

2. Lower transmitter with antenna and flange into the nozzle.

Gasket

3. Tighten bolts and nuts with sufficient torque for the flange and gasket

choice.

4. Align the transmitter head (see Chapter 4).

3.2 Flanged version with air purge ring (option code PC1)

1. If applicable, assemble the segmented cone antenna (see Chapter 9).

March 2018 Quick Start Guide

Quick Start Guide 5

2. Place a suitable gasket on the tank flange.

3. Place the purge ring over the gasket.

4. Place a suitable gasket over the purge ring.

Note

A minimum gasket thickness of 0.125 in. (3.2 mm) is required for flanges

with protective plate design.

5. Lower transmitter with antenna and flange into the nozzle.

Quick Start Guide March 2018

6Rosemount 5408 and 5408:SIS Level Transmitters

Antenna with air purge holes

6. Tighten bolts and nuts with sufficient torque for the flange and gasket

choice.

1.0 in. (25.5 mm)

7. Connect the air purging system. Use thread sealant or suitable gasket

according to your site procedures.

March 2018 Quick Start Guide

Quick Start Guide 7

0.4 in. (10 mm)

G3/8-in.

Incoming Air Supply SpecificationTable 3-1:

Maximum pressure Recommended pressure

190 psi (13 bar) 100 to 115 psi (7 to 8 bar)

8. Align the transmitter head (see Chapter 4).

3.3 Threaded version, antenna diameter (D) < Thread

diameter (d)

3.3.1 Flanged tank connection

1. If applicable, assemble the segmented cone antenna (see Chapter 9).

2. Place a suitable gasket on the tank flange.

3. Place the customer supplied flange over the gasket.

Quick Start Guide March 2018

8Rosemount 5408 and 5408:SIS Level Transmitters

4. Tighten the bolts and nuts with sufficient torque for the flange and

gasket choice.

5. Apply anti-seize paste or PTFE tape on threads according to your site

procedures.

Gasket may be used as a sealant for adapters with 1½- or 2-in. BSPP

(G) threads.

6. Lower transmitter with antenna and flange into the nozzle.

March 2018 Quick Start Guide

Quick Start Guide 9

Gasket

(for 1½-in. and 2-in.

BSPP (G) threads only)

7. Align the transmitter head (see Chapter 4).

3.3.2 Threaded tank connection

1. If applicable, assemble the segmented cone antenna (see Chapter 9).

2. Apply anti-seize paste or PTFE tape on threads according to your site

procedures.

Gasket may be used as a sealant for adapters with 1½- or 2-in. BSPP

(G) threads.

3. Mount the transmitter on the tank.

Quick Start Guide March 2018

10 Rosemount 5408 and 5408:SIS Level Transmitters

Andere Handbücher für Rosemount 5408

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson Rosemount 3101 Bedienungsanleitung

Emerson

Emerson Micro Motion 9739 MVD Kurzanleitung

Emerson

Emerson Rosemount 8732E Bedienungsanleitung

Emerson

Emerson Rosemount 4600 Bedienungsanleitung

Emerson

Emerson Rosemount 8750W Bedienungsanleitung

Emerson

Emerson Solu Comp Xmt-P-FF/FI Bedienungsanleitung

Emerson

Emerson Micro Motion 1600 Bedienungsanleitung

Emerson

Emerson Rosemount 148 Bedienungsanleitung

Emerson

Emerson Rosemount 848T Bedienungsanleitung

Emerson

Emerson Rosemount 8732EM Bedienungsanleitung

Emerson

Emerson Rosemount 2051L Bedienungsanleitung

Emerson

Emerson Rosemount 3051SF Series Bedienungsanleitung

Emerson

Emerson Rosemount Ultrasonic 3107 Bedienungsanleitung

Emerson

Emerson Rosemount 4600 Bedienungsanleitung

Emerson

Emerson Rosemount Analytical HART 5081-A-HT Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Bedienungsanleitung

Emerson

Emerson Rosemount MultiVariable 3051SMV Bedienungsanleitung

Emerson

Emerson Rosemount 5408 Bedienungsanleitung

Emerson

Emerson Rosemount 3152 Bedienungsanleitung

Emerson

Emerson Rosemount 1408A Bedienungsanleitung

Emerson

Emerson Rosemount 644h Bedienungsanleitung

Emerson

Emerson Rosemount OCX8800A Bedienungsanleitung

Emerson

Emerson Rosemount 3051D Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Konfigurationshandbuch

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung