Emerson Rosemount ET210 Bedienungsanleitung

Quick Start Guide

00825-0100-4211, Rev AA

June 2019

Rosemount™ ET210 Wireless Corrosion

Transmitter

NOTICE

This guide provides basic guidelines for Rosemount Wireless Corrosion Transmitter. It does not provide

instructions for configuration, diagnostics, maintenance, service, troubleshooting or intrinsically safe

(I.S.) installations. Refer to the Rosemount Wireless Corrosion Transmitter Reference Manual for more

instruction. The manual and this guide are also available electronically on EmersonProcess.com

\Rosemount.

Shipping considerations

Each device contains two “D” size primary lithium-thionyl chloride battery cells. Primary lithium

batteries are regulated in transportation by the U.S. Department of Transportation, and are also

covered by IATA (International Air Transport Association), ICAO (International Civil Aviation

Organization), and ARD (European Ground Transportation of Dangerous Goods). It is the responsibility

of the shipper to ensure compliance with these or any other local requirements. Consult current

regulations and requirements before shipping.

WARNING

Explosions could result in death or serious injury.

Installation of this transmitter in an explosive environment must be in accordance with the

appropriate local, national, and international standards, codes, and practices. Review the approvals

section of this manual for any restrictions associated with a safe installation.

Before connecting a CC21 in an explosive atmosphere, make sure the instruments in the segment

are installed in accordance with intrinsically safe or non-incendive field wiring practices.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired

operation.

This device must be installed to ensure a minimum antenna separation distance of 20 cm (8 in.)

from all persons.

The power module may be replaced in a hazardous area. The power module has surface

resistivity greater than one gigaohm and must be properly installed on the wireless device.

Care must be taken during transportation to and from the point of installation to prevent a

potential electrostatic charging hazard.

Polymer enclosure has surface resistivity greater than one gigaohm. Care must be taken

during transportation to and from the point of installation to prevent a potential electrostatic

charging hazard.

WARNING

Physical access

Unauthorized personnel may potentially cause significant damage to and/or misconfiguration of

end users’ equipment. This could be intentional or unintentional and needs to be protected against.

Physical security is an important part of any security program and fundamental to protecting your

system. Restrict physical access by unauthorized personnel to protect end users’ assets. This is true

for all systems used within the facility.

Quick Start Guide June 2019

2 Emerson.com/RosemountEmerson.com/Rosemount

Contents

Overview......................................................................................................................................5

Wireless considerations................................................................................................................7

Field communicator connections................................................................................................. 8

Physical installation...................................................................................................................... 9

Commissioning device............................................................................................................... 12

Product certifications................................................................................................................. 15

June 2019 Quick Start Guide

Quick Start Guide 3

Quick Start Guide June 2019

4 Emerson.com/RosemountEmerson.com/Rosemount

1 Overview

Figure 1-1: Rosemount ET210 Wireless Corrosion Transmitter

A. Antenna

B. Power module

C. Head

D. Lanyard hole

E. Strap slot

F. Foot

G. Cap

H. Shoe

June 2019 Quick Start Guide

Quick Start Guide 5

1.1 Required equipment - IK220

1.2 Required tooling

Tooling is supplied in the Permasense IK220 Installation Kit:

•Hex key, 2.5mm, for power module retaining bolts

•Strap tightening tool - HCL SM-FT-2000

1.3 What's in the box

•Permasense ET210 sensor, complete with protective cap

•Lanyard kit, 316 stainless steel lanyard 6.5ft. (2m) in length, Gripple

No.2, release key

•Silicone rubber shoe

•Strap kit, comprising polymer strap and buckle

•Permasense BP20E power module

•M3 x 16mm stainless steel retaining bolts, two per sensor

Quick Start Guide June 2019

6 Emerson.com/RosemountEmerson.com/Rosemount

2 Wireless considerations

Power up sequence

The Emerson Smart Wireless Gateway should be installed and functioning

properly before any wireless devices are powered. Commission the

Rosemount ET210 and install the BP20E power module to power the device

only (following instructions below) after the gateway has been installed and

functioning. This results in a simpler and faster network installation.

Enabling active advertising on the Gateway ensures new devices are able to

join the network faster. For more information see the Smart Wireless

Gateway Manual (document number 00809-0200-4420).

Antenna position

The antenna is internal to the ET210 transmitter. The antenna should also be

approximately 3 ft. (1 m) from any large structure, building, or conductive

surface to allow for clear communication to other devices.

June 2019 Quick Start Guide

Quick Start Guide 7

3 Field communicator connections

The CC21 commissioning cable is connected and removed from the

transmitter in the same way as BP20E power module. The USB connector is

plugged in to the tablet PC as shown in Figure 3-1.

Figure 3-1: IK220 Commissioning Kit

A. Tablet PC

B. CC21

C. USB cable plugged into USB port

D. WT210/ET210 sensor

Quick Start Guide June 2019

8 Emerson.com/RosemountEmerson.com/Rosemount

4 Physical installation

4.1 Mounting the sensor

Procedure

1. Identify the location where the sensor should be fixed. Clean the area

where the sensor will touch the pipe, mainly to remove any particles

which might keep the transducer away from the pipe surface or

damage the face of the transducer. Use a permanent marker to show

exactly where each sensor is to be placed.

2. Remove the protective cap from the sensor. Ensure tools and

fastenings are kept away from the sensor when the cap is removed.

Ensure the metal ring and the rubber shoe are fitted before installing

the sensor. If either part is missing, do not proceed with the

installation.

3. Place the sensor in the required location on the pipe.

Note

The magnets used in the sensors have a high pull force. To avoid

damage, and to get the precise location for each sensor, put the

sensor at an angle to the pipe and then gently lower the shoe onto

the pipe.

4. Cut the strap to a suitable length. This will depend on the diameter of

the pipe. If the diameter of the pipe is D cm / inches, the length can

be approximated by 3 x (D + 10) cm (or 3 x (D + 4) inches).

June 2019 Quick Start Guide

Quick Start Guide 9

5. Attach a buckle to one end of the strap. Ensure the strap teeth are on

the outside of the strap, and are fully engaged with the buckle.

Note

A small flat screwdriver can be used to disengage the buckle, if

required.

6. Slide the strap through the sensor(s), pass the strap through the

buckle. Where possible position the buckle opposite the middle

sensor to ensure both sides of the strap are tightened evenly.

7. Tighten the strap by hand to gently hold the sensor in place. If

necessary, adjust the position of the sensor to ensure correct

alignment around the circumference of the pipe. With multiple

sensors on a strap, there should be a gap between the shoes of

adjacent sensors.

8. Prepare the lanyard kit and decide how it will be positioned. Wrap the

lanyard around the circumference of the pipe. The 7 ft. (2m) length

will accommodate a maximum diameter of 24 in. When it is not

possible to wrap the lanyard around a pipe, find an alternative

attachment point for the lanyard.

9. Thread the bare end of the wire through the loop in the lanyard to

secure it to the pipe.

10. Feed the bare end of the lanyard into the ‘gripple’ and push the

‘gripple’ 6 in. (15 cm) up from the bare end.

Quick Start Guide June 2019

10 Emerson.com/RosemountEmerson.com/Rosemount

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson Rosemount 702 Bedienungsanleitung

Emerson

Emerson Rosemount 644h Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Bedienungsanleitung

Emerson

Emerson Rosemount 5600 Series Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Series Bedienungsanleitung

Emerson

Emerson Rosemount 1152 Alphaline Bedienungsanleitung

Emerson

Emerson Rosemount 8732EM Bedienungsanleitung

Emerson

Emerson Rosemount 5081-T Bedienungsanleitung

Emerson

Emerson Rosemount 644h Bedienungsanleitung

Emerson

Emerson PT5N Series Bedienungsanleitung

Emerson

Emerson Micro Motion 5700 Kurzanleitung

Emerson

Emerson Rosemount ET310C Bedienungsanleitung

Emerson

Emerson Rosemount 3051SF Series Bedienungsanleitung

Emerson

Emerson Rosemount 644 Bedienungsanleitung

Emerson

Emerson Rosemount 3051 CF Series Bedienungsanleitung

Emerson

Emerson Rosemount 8712C Konfigurationshandbuch

Emerson

Emerson PT5N FLR Series Bedienungsanleitung

Emerson

Emerson Rosemount 3308 Series Bedienungsanleitung

Emerson

Emerson Rosemount 2051CF series Bedienungsanleitung

Emerson

Emerson Micro Motion 5700 Bedienungsanleitung

Emerson

Emerson Micro Motion Transmitters and Discrete Controllers Series... Betriebshandbuch

Emerson

Emerson Rosemount FCL-01 Bedienungsanleitung

Emerson

Emerson Rosemount 3408 Bedienungsanleitung

Emerson

Emerson Micro Motion 2400S Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung