Endon EL-40065 Bedienungsanleitung

The Light pack contains:

Wall light with separate shade parts.

Terminal block.

The following tools may be required:

Selection of cross and flat head screwdrivers.

Electric drill and assorted drill bits.

Wire strippers.

Electrical insulation tape.

INSTRUCTION MANUAL

This product is only suitable for connection to a 240V~50Hz supply.

It is recommended that this light is installed by a qualified electrician in accordance with current IEE Wiring

Regulations and local Building Regulations.

The light fitting should be connected to a lighting circuit protected by a 5 amp fuse (or a 6 amp miniature

circuit breaker).

This light has an IP44 (splash proof) rating suitable for use outdoors.

Run supply wire from a 5-amp electrical supply using double insulated 3-core cable of type H05RN-F 1.0mm2

(not supplied) to selected site, ensuring it is adequately protected through the full length of the cable run, it

must come out of the flat surface of the mounting surface in line with the entry to the fitting.

Except where installed in a conduit or duct , which provides equivalent protection against mechanical damage,

a cable buried in the ground shall incorporate an earthed armour or metal sheath or both, suitable for use as a

protective conductor, or be of insulated concentric construction. Buried cables shall be marked by cable

covers or a suitable marking tape. Buried conduits and ducts shall be suitably identified. Buried cables,

conduits and ducts shall be at a sufficient depth to avoid being damaged by any reasonably foreseeable

disturbance of the ground.

This product contains breakable parts – be careful during handling and maintenance to avoid breakage.

The diffuser (cover) can become hot in use. Switch off and allow 10 minutes to cool before cleaning (using a

dry cloth only – do not use liquid or abrasive cleaners).

If the cover is broken or cracked then it must be replaced immediately to preserve the water ingress

protection, please consult your retailer. This is represented by the symbol

If any modification is made it will invalidate the warranty and may render the product unsafe.

Before you start

Please read these instructions carefully before fitting your new light and retain for reference.

Switch off the mains supply and remove the appropriate fuse or switch off the appropriate circuit breaker

before commencing installation.

Ensure that no one else has access that would enable the supply to be inadvertently reconnected.

Check the packaging and make sure that you have all the required parts.

Follow each assembly step in order to prevent incorrect assembly

Make sure all screws / nuts, including electrical connections etc are fully tightened before use.

EL- 40064, EL- 40065 and EL- 40066 Outdoor wall fittings.

Safety Warnings

Endon Lighting Ltd

Leeds

LS9 0SE

These assembly diagrams are intended as a guide – if in doubt consult a qualified electrician.

Assembly / user instructions

N210 102v1

Diagram A

Diagram B

Diagram C

1. Diagram A. Remove the back plate by undoing the 2

decorative nuts from the threaded bolts. Unscrew the

glass cover. Secure the 2 sections of the shade onto

the lamp holder housing with the screws provided.

2. Diagram B. Fit the 2 threaded posts in the back plate

and bring the mains cable through the rubber

grommet then use the back plate as a template and

mark the 2 fixings holes, making sure the back plate

is correctly aligned so that the threaded bolts are

horizontal. Use appropriate fixings to secure the back

plate to the wall.

3. Diagram C. Connect the house wiring to the internal

terminal block. The cable entry grommet must be

securely in place to ensure that the water ingress

protection is maintained. NOTE: This is a Class I

fitting and must be earthed. Connect the incoming

mains as per the diagram.

4. Diagram D. Fit the terminal block onto the post in the

back plate and then fit the front frame over the 2

threaded bolts in the back plate and secure with the 2

decorative nuts. Take care not to trap or strain the

internal cables.

5. Fit the appropriate bulb into the lamp holder NOTE:

Never fit bulbs of a higher wattage than those

specified on the label (as these may cause

overheating and damage the fitting).

6. Fit the glass cover making sure any seals are

replaced.

7. Turn on the power and test.

Diagram D

Fixing screws

Threaded bolts

Terminal post

Decorative nuts

Glass cover

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Endon Außenleuchte Handbücher

Endon

Endon Grant YG-7501 Bedienungsanleitung

Endon

Endon Roko Bedienungsanleitung

Endon

Endon YG- 8002 Bedienungsanleitung

Endon

Endon Breton Outdoor Wall light Fitting Bedienungsanleitung

Endon

Endon Burford Outdoor Post Light Bedienungsanleitung

Endon

Endon YG-0923 Bedienungsanleitung

Endon

Endon YG-3000 Bedienungsanleitung

Endon

Endon YG-861-SS Bedienungsanleitung

Endon

Endon EL-40094 Bedienungsanleitung

Endon

Endon Leyton Bedienungsanleitung

Endon

Endon Burford Wall Bedienungsanleitung

Endon

Endon Carlson Bedienungsanleitung

Endon

Endon Middleton EL-40017 Bedienungsanleitung

Endon

Endon EL-YG -5006 Bedienungsanleitung

Endon

Endon EL-YG-5006 Bedienungsanleitung

Endon

Endon EL-40053 Bedienungsanleitung

Endon

Endon Burford 76549 Handbuch

Endon

Endon York 1lt Wall Bedienungsanleitung

Endon

Endon Elan 5lt Bedienungsanleitung

Endon

Endon Pagoda PIR Outdoor Wall Light Bedienungsanleitung

Endon

Endon Cambridge Wall Light Bedienungsanleitung

Endon

Endon EL-40085 Bedienungsanleitung

Endon

Endon YG-8000 Bedienungsanleitung

Endon

Endon EL- 40101 Bedienungsanleitung

Beliebte Außenleuchte Handbücher anderer Marken

Sealey

Sealey LED37 Bedienungsanleitung

nordlux

nordlux VEJERS Benutzerhandbuch

SImx

SImx ELITE LED LHTC637 Bedienungsanleitung

GEV

GEV CAROLINE 10833 Bedienungsanleitung

NEBO

NEBO NEB-LSP-0020 Bedienungsanleitung

WE-EF

WE-EF PFL540 LED Bedienungsanleitung

Lindby

Lindby 9949029 Bedienungsanleitung

HEPER

HEPER DOGO Side LW6048.585-US Montage- und Bedienungsanleitung

HEPER

HEPER LW8034.003-US Montage- und Bedienungsanleitung

Maretti

Maretti VIBE S 14.6080.04.A Bedienungsanleitung

BEGA

BEGA 84 253 Handbuch

HEPER

HEPER MINIMO Montage- und Bedienungsanleitung

LIGMAN

LIGMAN BAMBOO 3 Bedienungsanleitung

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Bedienungsanleitung

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Bedienungsanleitung

urban ambiance

urban ambiance UQL1273 Bedienungsanleitung

TotalPond

TotalPond 52238 Bedienungsanleitung

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Bedienungsanleitung