Endon EL-40094 Bedienungsanleitung

The Light pack contains:

Wall light and bracket.

Terminal connection block.

GU10 lamps

The following tools may be required:

Selection of cross and flat head screwdrivers.

Electric drill and assorted drill bits.

Wire strippers.

Electrical insulation tape.

INSTRUCTION MANUAL

These products are only suitable for connection to a 240V~50Hz supply.

It is recommended that these lights are installed by a qualified electrician in accordance with current IEE

Wiring Regulations and Building Regulations (Part P).

These fittings should be connected to a lighting circuit protected by a 5 amp fuse (or a 6 amp miniature circuit

breaker).

These lights have an IP44 (splash proof) rating suitable for use outdoors.

Run supply wire from a 5-amp electrical supply using double insulated 3-core cable of type H05RN-F 1.0mm2

(not supplied) to selected site, ensuring it is adequately protected through the full length of the cable run, it

must come out of the flat surface of the mounting surface in line with the entry to the fitting.

Except where installed in a conduit or duct , which provides equivalent protection against mechanical damage,

a cable buried in the ground shall incorporate an earthed armour or metal sheath or both, suitable for use as a

protective conductor, or be of insulated concentric construction. Buried cables shall be marked by cable

covers or a suitable marking tape. Buried conduits and ducts shall be suitably identified. Buried cables,

conduits and ducts shall be at a sufficient depth to avoid being damaged by any reasonably foreseeable

disturbance of the ground.

These products contain breakable parts – be careful during handling and maintenance to avoid breakage.

The shades can become hot in use. Switch off and allow 10 minutes to cool before cleaning (using a dry cloth

only – do not use liquid or abrasive cleaners).

If the covers are broken or cracked then they must be replaced immediately to preserve the water ingress

protection, please consult your retailer. This is represented by the symbol

IMPORTANT: To achieve maximum corrosion resistance the surface of the Stainless Steel must be kept clean.

Surface contamination and the formation of deposits are critical factors which may lead to drastically reduced

life. An example is salt deposits from marine conditions. Cleaning with soap or a mild detergent and warm

water followed by a careful clean water rinse and finally wiping dry is usually adequate for most S/S items

used in the domestic environment. Care must be taken to turn off the mains supply until the cleaning process

has been completed and the fitting is completely dry.

If any modification is made it will invalidate the warranty and may render the product unsafe.

Before you start

Please read these instructions carefully before fitting your new light and retain for reference.

Switch off the mains supply and remove the appropriate fuse or switch off the appropriate circuit breaker

before commencing installation.

Ensure that no one else has access that would enable the supply to be inadvertently reconnected.

Check the packaging and make sure that you have all the required parts.

Follow each assembly step in order to prevent incorrect assembly

Make sure all screws / nuts, including electrical connections etc are fully tightened before use.

This type of Light Fitting may be connected to a Dimmer if a Tungsten incandescent bulb is used (as

supplied). If a CFL type bulb is fitted then these cannot (generally) be controlled by a dimmer.

EL- 40094 / EL- 40095 – Single / Twin Outdoor wall fittings.

Safety Warnings

Endon Lighting

LS9 0SE

20150810

These assembly diagrams are intended as a guide – if in doubt consult a qualified electrician. The

twin light has been shown here but the same general instruction applies to the single light version.

Assembly / user instructions

N210 116

Diagram A

Diagram B

Diagram C

1. Determine the position of your light

fitting taking into account the exit

position of the cable. Ensure that the

mounting surface is solid, preferably a

brick or block wall and ensure that

there are no other cables or pipes

beneath the surface. Use appropriate

fixings. Wall plugs and screws as

supplied are shown here.

2. Diagram A. Separate the plastic back

plate from the fitting by removing the

two domed nuts / washers (1) on the

front of the fitting. Leave the threaded

(2) bolts in the back plate.

3. Diagram B. The internal terminal block

(3) can be removed from its mounting

position inside the back plate to ease

fitment of the back plate. Use the back

plate as a template to mark the screw

holes. Make sure the back plate is

correctly aligned with the drain hole (4)

at the lowest position. NOTE: The

GU10 bulbs will be fitted on receipt but

at times of replacement, the bulb cover

end caps (5) need to be unscrewed

and then the bulbs removed / fitted.

4. Use a sharp object such as a

screwdriver to pierce the rubber

grommet in the back plate. Feed the

incoming cable (6) through the rubber

grommet and attach the back plate to

the wall. Do not over tighten as this

could damage the back plate.

5. Connect the house wiring to the

internal terminal block (3). NOTE: This

is a Class I fitting and must be

earthed.

See wiring details.

6. Diagram C. Place the fitting over the

back plate, ensuring that the bolts in

the back plate are aligned with the

holes in the front of the fitting. Replace

the domed nuts / washers (1) to secure

the fitting. Do not over tighten. Fit the

bulbs (7) (supplied) into the lamp

holders – see NOTE in 3 above.

NOTE: Never fit bulbs of a higher

wattage or of a type other than those

specified on the label (as these may

cause overheating and damage the

fitting).

7. Fit the bulb covers (5).

8. Turn on the power and test.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Endon Außenleuchte Handbücher

Endon

Endon EL-40065 Bedienungsanleitung

Endon

Endon Carlson Bedienungsanleitung

Endon

Endon EL-40085 Bedienungsanleitung

Endon

Endon Pagoda PIR Outdoor Wall Light Bedienungsanleitung

Endon

Endon Middleton EL-40017 Bedienungsanleitung

Endon

Endon EL-40098 Bedienungsanleitung

Endon

Endon Burford Outdoor Post Light Bedienungsanleitung

Endon

Endon 56410 Bedienungsanleitung

Endon

Endon Dean 82013 Bedienungsanleitung

Endon

Endon EL-533-28W-T5 Bedienungsanleitung

Endon

Endon Canillo Bedienungsanleitung

Endon

Endon EL- 40101 Bedienungsanleitung

Endon

Endon Burford Wall Bedienungsanleitung

Endon

Endon YG-864-SS Bedienungsanleitung

Endon

Endon Burford 76549 Handbuch

Endon

Endon Leyton Bedienungsanleitung

Endon

Endon YG-7501 Bedienungsanleitung

Endon

Endon YG-4002-SS Bedienungsanleitung

Endon

Endon EL-40022 Bedienungsanleitung

Endon

Endon YG-6002-SS Bedienungsanleitung

Endon

Endon Roko Bedienungsanleitung

Endon

Endon Joshua Bedienungsanleitung

Endon

Endon Breton Outdoor Wall light Fitting Bedienungsanleitung

Endon

Endon YG-3004 Bedienungsanleitung

Beliebte Außenleuchte Handbücher anderer Marken

Sealey

Sealey LED37 Bedienungsanleitung

nordlux

nordlux VEJERS Benutzerhandbuch

SImx

SImx ELITE LED LHTC637 Bedienungsanleitung

GEV

GEV CAROLINE 10833 Bedienungsanleitung

NEBO

NEBO NEB-LSP-0020 Bedienungsanleitung

WE-EF

WE-EF PFL540 LED Bedienungsanleitung

Lindby

Lindby 9949029 Bedienungsanleitung

HEPER

HEPER DOGO Side LW6048.585-US Montage- und Bedienungsanleitung

HEPER

HEPER LW8034.003-US Montage- und Bedienungsanleitung

Maretti

Maretti VIBE S 14.6080.04.A Bedienungsanleitung

BEGA

BEGA 84 253 Handbuch

HEPER

HEPER MINIMO Montage- und Bedienungsanleitung

LIGMAN

LIGMAN BAMBOO 3 Bedienungsanleitung

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Bedienungsanleitung

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Bedienungsanleitung

urban ambiance

urban ambiance UQL1273 Bedienungsanleitung

TotalPond

TotalPond 52238 Bedienungsanleitung

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Bedienungsanleitung