Endress+Hauser Oxymax COS22 Series Bedienungsanleitung

BA446C/07/EN/01.11

71098071

Operating Instructions

Oxymax COS22

Dissolved oxygen sensor

Notes for using this manual

Warning instructions and their meaning

The structure, signal words and safety colors of the signs comply with the specifications of ANSI Z535.6

("Product safety information in product manuals, instructions and other collateral materials").

Cross reference symbols

Safety message structure Meaning

DANGER

Cause (/consequences)

Consequences if safety

message is not heeded

►Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid the situation will result in a fatal or serious injury.

WARNING

Cause (/consequences)

Consequences if safety

message is not heeded

►Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid the situation can result in a fatal or serious injury.

CAUTION

Cause (/consequences)

Consequences if safety

message is not heeded

►Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid this situation can result in minor or medium injury.

NOTICE

Cause/situation

Consequences if safety

message is not heeded

►Action/note

This symbol alerts you to situations that can result in damage to

property and equipment.

È ä 1 This symbol indicates a cross reference to a defined page (e.g. p. 1).

È å 2 This symbol indicates a cross reference to a defined figure (e.g. fig. 2).

Endress+Hauser

Table of contents

1 Safety instructions . . . . . . . . . . 4

1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Installation, commissioning and operation . 4

1.3 Operational safety . . . . . . . . . . . . . . . . . . . 5

1.4 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Identification . . . . . . . . . . . . . . 6

2.1 Order code . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2 Scope of delivery . . . . . . . . . . . . . . . . . . . . 6

2.3 Certificates and approvals . . . . . . . . . . . . . . 6

3 Installation . . . . . . . . . . . . . . . . 7

3.1 Incoming acceptance, transport, storage . . . 7

3.2 Installation conditions . . . . . . . . . . . . . . . . 7

3.3 Installation instructions . . . . . . . . . . . . . . . 8

3.4 Installation examples . . . . . . . . . . . . . . . . 10

3.5 Post-installation check . . . . . . . . . . . . . . . 12

4 Wiring . . . . . . . . . . . . . . . . . . 13

4.1 Connection to the transmitter . . . . . . . . . 13

4.2 Post-connection check . . . . . . . . . . . . . . . 13

5 Function . . . . . . . . . . . . . . . . . 14

5.1 Measuring principle . . . . . . . . . . . . . . . . . 14

5.2 Calibration . . . . . . . . . . . . . . . . . . . . . . . . 15

6 Commissioning. . . . . . . . . . . . 18

6.1 Function check . . . . . . . . . . . . . . . . . . . . 18

6.2 Polarization . . . . . . . . . . . . . . . . . . . . . . . 18

6.3 Calibration . . . . . . . . . . . . . . . . . . . . . . . . 19

7 Maintenance. . . . . . . . . . . . . . 20

7.1 Maintenance tasks . . . . . . . . . . . . . . . . . . 20

7.2 Maintenance intervals . . . . . . . . . . . . . . . 20

7.3 Cleaning the sensor . . . . . . . . . . . . . . . . . 21

7.4 Wear parts and consumables . . . . . . . . . . 21

8 Accessories. . . . . . . . . . . . . . . 25

8.1 Connection accessories . . . . . . . . . . . . . . 25

8.2 Installation accessories . . . . . . . . . . . . . . . 25

9 Trouble-shooting. . . . . . . . . . . 26

9.1 Trouble-shooting instructions . . . . . . . . . . 26

9.2 Spare parts and consumable material . . . . . 27

9.3 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

9.4 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . 27

10 Technical data . . . . . . . . . . . . . 28

10.1 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

10.2 Performance characteristics . . . . . . . . . . . . 28

10.3 Environment . . . . . . . . . . . . . . . . . . . . . . 29

10.4 Process . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

10.5 Mechanical construction . . . . . . . . . . . . . . 31

Index. . . . . . . . . . . . . . . . . . . . 33

Safety instructions

4Endress+Hauser

1 Safety instructions

1.1 Designated use

The oxygen sensor is suitable for continuous measurement of dissolved oxygen in water.

The specific suitability depends on the sensor design:

• COS22-1 (standard, measuring range 0.01 to 60 mg/l)

– Measuring, monitoring and regulating the oxygen content in fermenters

– Monitoring the oxygen content in biotechnology facilities

• COS22-3 (trace measurement, measuring range 0.001 to 10 mg/l, preferred operational range

0.001 to 2 mg/l), also suitable for high CO2partial pressure

– Monitoring inertization equipment in the food industry

– Monitoring the residual oxygen content in carbonated fluids of the beverage industry

– Trace measurement in industrial applications such as inertizations

– Monitoring the residual oxygen content in boiler feedwater

– Monitoring, measuring and regulating the oxygen content in chemical processes

NOTICE

Molecular hydrogen

Hydrogen causes sensitivity in other substances and leads to false low readings or, at the worst, total

failure of the sensor.

►Do not use the sensor in media containing hydrogen.

Any other use than the one described here compromises the safety of persons and the entire measuring

system and is not permitted.

The manufacturer is not liable for damage caused by improper or non-designated use.

1.2 Installation, commissioning and operation

Please note the following items:

• Installation, commissioning, operation and maintenance of the measuring system must only be

carried out by trained technical personnel.

Trained personnel must be authorized for the specified activities by the system operator.

• Electrical connection must only be carried out by a certified electrician.

• Technical personnel must have read and understood these Operating Instructions and must adhere

to them.

• Before commissioning the entire measuring point, check all the connections. Ensure that electrical

cables and hose connections are not damaged.

• Do not operate damaged products and secure them against unintentional commissioning. Mark the

damaged product as being defective.

• Measuring point faults may only be rectified by authorized and specially trained personnel.

• If faults can not be rectified, the products must be taken out of service and secured against

unintentional commissioning.

• Repairs not described in these Operating Instructions may only be carried out at the manufacturer’s

or by the service organization.

Safety instructions

Endress+Hauser 5

1.3 Operational safety

The sensor has been designed and tested according to the state of the art and left the factory in perfect

functioning order.

Relevant regulations and European standards have been met.

As the user, you are responsible for complying with the following safety conditions:

• Installation instructions

• Local prevailing standards and regulations.

1.4 Return

If the sensor has to be repaired, please return it cleaned to the sales center responsible.

Please use the original packaging, if possible.

Before returning the device, please clarify all formalities - such as obtaining an identification number -

with your sales center.

Please enclose the completed "Declaration of Hazardous Material and De-Contamination" (copy the

second last page of these Operating Instructions) with the packaging and the transportation documents.

No repair without completed declaration!

Identification

6Endress+Hauser

2 Identification

2.1 Order code

To find out the version of your device, enter the order code indicated on the nameplate in the

search screen at the following address: www.products.endress.com/order-ident

2.2 Scope of delivery

The following items are included in the delivery:

• Oxygen sensor with tap water filled cap for membrane protection

• Electrolyte, 1 bottle, 10 ml (0.34 fl.oz.)

• Brief Operating Instructions

• Operating Instructions on CD

If you have any questions, please contact your supplier or your local sales center.

2.3 Certificates and approvals

The manufacturer declares the FDA compliance of the materials used.

Ask your local sales center for the certificates.

Product FDA certificate for

COS22-****22 Membrane, O-rings, process sealing

COS22Z-*2*2 Membrane, O-rings, process sealing

COS22-****23 Membrane, O-rings

COS22Z-*2*3 Membrane, O-rings

Installation

Endress+Hauser 7

3 Installation

3.1 Incoming acceptance, transport, storage

• Make sure the packaging is undamaged!

Inform the supplier about any damage to the packaging.

Keep the damaged packaging until the matter has been settled.

• Make sure the contents are undamaged!

Inform the supplier about damage to the contents. Keep the damaged products until the matter has

been settled.

• Check that the order is complete and agrees with your shipping documents.

• The packaging material used to store or to transport the product must provide shock protection and

humidity protection. The original packaging offers the best protection. Also, keep to the approved

ambient conditions (see "Technical data").

• If you have any questions, please contact your supplier or your local sales center.

3.2 Installation conditions

3.2.1 Angle of installation

The sensor must be installed with an inclination angle of at least 10 ˚to the horizontal in an assembly,

support or a corresponding process connection. Other inclination angles are not permitted. Do not

install the sensor overhead.

Observe the instructions for installing sensors in the Operating Instructions for the assembly used.

a0005584-en

Fig. 1: Permitted angle of installation

10° 10° Not permissible!

Not permissible!

Permissible angle of installation

Installation

8Endress+Hauser

3.2.2 Mounting location

• Select the installation location so that there is easy access for later calibration.

• Make sure that upright posts and assemblies are secured safely and vibration-free.

• Select an installation location which produces a typical oxygen concentration.

3.3 Installation instructions

3.3.1 Measuring system

A complete measuring system comprises:

• A digital oxygen sensor Oxymax COS22

• A transmitter, e.g. Liquisys COM223/253F

• An appropriate measuring cable, e.g. COK21

• Optional: an assembly, e.g. fixed installation assembly CPA442, flow assembly CPA240 or retractable

assembly CPA475

a0006653

Fig. 2: Example of a measuring system with COS22

1 Oxygen sensor COS22

2 Retractable assembly CPA475

3 Measuring cable COK21

4 Transmitter Liquisys COM253F

CAL REL

REL1

ALARM

REL2

Installation

Endress+Hauser 9

3.3.2 Installing a measuring point

WARNING

Electrical voltage

In the event of a fault, non-grounded metallic assemblies may be under voltage and then are not

touchable.

►When using metallic assemblies and installation equipment, observe the national grounding

provisions.

For a complete installation of a measuring point, proceed as follows:

1. Install a retractable or a flow assembly (if used) into the process.

2. Connect the water supply to the rinse connections (if you use an assembly with cleaning function).

3. Install and connect the oxygen sensor.

NOTICE

Installation errors

Cable breakage, loss of the sensor, unintended unscrewing of the membrane cap

►Do not install the sensor suspended from the cable.

►Screw the sensor into the assembly so that the cable is not twisted.

►Mounting or dismounting the sensor: hold the sensor body, only turn the threaded plug-in head

while screwing the sensor in or out of the assembly. Otherwise you could unscrew the sensor’s

membrane cap. It will remain in the assembly resp. in the process then.

►Avoid exerting excessive tensile force on the cable (e.g. from jerky pulling).

►Select the installation location so that there is easy access for later calibration.

Installation

10 Endress+Hauser

3.4 Installation examples

3.4.1 Fixed installation (CPA442)

The CPA442 fixed installation assembly allows a sensor to be easily adapted to almost any process

connections from Ingold nozzles to Varivent or Triclamp connections.

This type of installation is very suitable for tanks and larger pipes. The sensor achieves a defined

immersion depth in the medium in an easy manner.

3.4.2 Flow assembly

CPA240

The CPA240 flow assembly offers up to three installation slots for sensors with a shaft diameter of 12

mm (0.47"), a shaft length of 120 mm (4.72") and a process connection Pg 13.5.

It is very suitable for use in pipes or at hose connections.

During trace measurement in particular, ensure the assembly is completely vented to avoid measuring

errors.

a0005720

Fig. 3: CPA240 flow assembly with protective hood

a0005721

Fig. 4: Bypass installation

1 Main line

2Mediumremoval

3, 6 Manually actuated or solenoid valves

4 Sampling

5 Flow assembly with installed sensor

7 Medium return

Andere Handbücher für Oxymax COS22 Series

Inhaltsverzeichnis

Andere Endress+Hauser Zubehör Handbücher

Endress+Hauser

Endress+Hauser ISEmax CAS40D Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltapilot S FMB70 Montageanleitung

Endress+Hauser

Endress+Hauser Turbimax W CUS31 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline 200 PROFIBUS PA Technische Daten

Endress+Hauser

Endress+Hauser Memosens COS81D Bedienungsanleitung

Endress+Hauser

Endress+Hauser Oxymax COS61 Handbuch

Endress+Hauser

Endress+Hauser Deltapilot S DB50 Handbuch

Endress+Hauser

Endress+Hauser omnigrad M TR 44 Handbuch

Endress+Hauser

Endress+Hauser Proline Promag H Technische Daten

Endress+Hauser

Endress+Hauser Condumax CLS15 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Turbimax CUS51D Bedienungsanleitung

Endress+Hauser

Endress+Hauser Tophit CPS471 Handbuch

Endress+Hauser

Endress+Hauser Cleanfit P CPA472 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Chloromax CCS142D Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline 200 FOUNDATION Fieldbus Technische Daten

Endress+Hauser

Endress+Hauser Liquipoint T Series Handbuch

Endress+Hauser

Endress+Hauser NAR 300 Technische Daten

Endress+Hauser

Endress+Hauser Memosens COS51E Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Prosonic S Series Handbuch

Endress+Hauser

Endress+Hauser Prosonic S Series Handbuch

Endress+Hauser

Endress+Hauser Indumax CLS54 Bedienungsanleitung

Endress+Hauser

Endress+Hauser CCS120D Bedienungsanleitung

Endress+Hauser

Endress+Hauser Oxymax COS61 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung