Endress+Hauser Cerabar PMC11 Bedienungsanleitung

Products Solutions Services

Operating Instructions

Cerabar PMC11, PMC21, PMP11,

PMP21, PMP23

Process pressure measurement

Pressure transducer for safe measurement and

monitoring of absolute and gauge pressure

BA01271P/00/EN/05.17

71353696

Cerabar PMC11, PMC21, PMP11, PMP21, PMP23

2 Endress+Hauser

Order code:

Ext. ord. cd.:

Ser. no.:

www.endress.com/deviceviewer Endress+Hauser

Operations App

XXXXXXXXXXXX

XXXXX-XXXXXX

XXX.XXXX.XX

Serial number

A0023555

• Make sure the document is stored in a safe place such that it is always available when

working on or with the device.

• To avoid danger to individuals or the facility, read the "Basic safety instructions" section

carefully, as well as all other safety instructions in the document that are specific to

working procedures.

• The manufacturer reserves the right to modify technical data without prior notice. Your

Endress+Hauser distributor will supply you with current information and updates to

these Instructions.

Cerabar PMC11, PMC21, PMP11, PMP21, PMP23 Table of contents

Endress+Hauser 3

Table of contents

1 Document information .............. 4

1.1 Document function ..................... 4

1.2 Symbols used .......................... 4

1.3 Documentation ........................ 5

1.4 Terms and abbreviations ................. 7

1.5 Turn down calculation ................... 8

2 Basic safety instructions ............ 9

2.1 Requirements concerning the staff .......... 9

2.2 Designated use ........................ 9

2.3 Workplace safety ...................... 10

2.4 Operational safety ..................... 10

2.5 Product safety ........................ 10

3 Product description ................ 11

3.1 Product design ........................ 11

3.2 Function ............................ 11

4 Incoming acceptance and product

identification ..................... 13

4.1 Incoming acceptance ................... 13

4.2 Product identification ................... 14

4.3 Storage and transport .................. 14

5 Installation ....................... 16

5.1 Mounting dimensions .................. 16

5.2 Installation conditions .................. 16

5.3 Influence of the installation position ........ 16

5.4 Mounting location ..................... 17

5.5 Mounting the profiled seal for the universal

process adapter ....................... 18

5.6 Mounting instructions for oxygen

applications .......................... 18

5.7 Post-installation check .................. 19

6 Electrical connection .............. 20

6.1 Connecting the measuring unit ............ 20

6.2 Connection conditions .................. 21

6.3 Connection data ....................... 21

6.4 Post-connection check .................. 22

7 Operation options ................. 23

7.1 Plug-on display PHX20 (optional) .......... 23

8 Diagnostics and troubleshooting ... 26

8.1 Troubleshooting ...................... 26

8.2 Response of output to errors .............. 26

8.3 Disposal ............................ 26

9 Maintenance ...................... 26

9.1 Exterior cleaning ...................... 27

10 Repair ............................ 28

10.1 General notes ........................ 28

10.2 Return .............................. 28

11 Accessories ....................... 29

11.1 Weld-in adapter ...................... 29

11.2 Process adapter M24 ................... 29

11.3 Plug-on display PHX20 ................. 30

11.4 M12 plug connectors ................... 30

12 Technical data .................... 31

12.1 Input ............................... 31

12.2 Output ............................. 35

12.3 Performance characteristics of ceramic

process isolating diaphragm .............. 37

12.4 Performance characteristics of metallic

process isolating diaphragm .............. 39

12.5 Environment ......................... 41

12.6 Process ............................. 43

Index .................................. 45

Document information Cerabar PMC11, PMC21, PMP11, PMP21, PMP23

4 Endress+Hauser

1 Document information

1.1 Document function

These Operating Instructions contain all the information that is required in various phases

of the life cycle of the device: from product identification, incoming acceptance and

storage, to mounting, connection, operation and commissioning through to

troubleshooting, maintenance and disposal.

1.2 Symbols used

1.2.1 Safety symbols

Symbol Meaning

DANGER

DANGER!

This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in

serious or fatal injury.

WARNING

WARNING!

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

serious or fatal injury.

CAUTION

CAUTION!

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or medium injury.

NOTICE

NOTE!

This symbol contains information on procedures and other facts which do not result in

personal injury.

1.2.2 Electrical symbols

Symbol Meaning Symbol Meaning

Protective ground connection

A terminal which must be connected

to ground prior to establishing any

other connections.

Ground connection

A grounded terminal which, as far as

the operator is concerned, is

grounded via a grounding system.

1.2.3 Tool symbols

Symbol Meaning

A0011222

Open-ended wrench

1.2.4 Symbols for certain types of information

Symbol Meaning

Permitted

Procedures, processes or actions that are permitted.

Forbidden

Procedures, processes or actions that are forbidden.

Tip

Indicates additional information.

Cerabar PMC11, PMC21, PMP11, PMP21, PMP23 Document information

Endress+Hauser 5

Symbol Meaning

Reference to documentation

Reference to page

Reference to graphic

,…

1. 2. 3.

Series of steps

Result of a step

Visual inspection

1.2.5 Symbols in graphics

Symbol Meaning

1, 2, 3 ... Item numbers

,…

1. 2. 3.

Series of steps

A, B, C, ... Views

1.3 Documentation

The document types listed are available:

In the Download Area of the Endress+Hauser Internet site: www.endress.com →

Download

1.3.1 Technical Information (TI): planning aid for your device

PMC11: TI01133P

PMP11: TI01133P

PMC21: TI01133P

PMP21: TI01133P

PMP23: TI01203P

The document contains all the technical data on the device and provides an overview of

the accessories and other products that can be ordered for the device.

1.3.2 Brief Operating Instructions (KA): getting the 1st measured

value quickly

KA01164P:

The Brief Operating Instructions contain all the essential information from incoming

acceptance to initial commissioning.

Document information Cerabar PMC11, PMC21, PMP11, PMP21, PMP23

6 Endress+Hauser

1.3.3 Safety Instructions (XA)

Safety Instructions (XA) are supplied with the device depending on the approval. These

instructions are an integral part of the Operating Instructions.

Device Directive Documentation Option 1)

PMP21

PMP23

ATEX II 1/2G Ex ia IIC T4 Ga/Gb XA01271P BA

PMC21 ATEX II 2G Ex ia IIC T4 Gb XA01271P BB

PMC21

PMP21

ATEX II 3G Ex ec IIC T4 Gc XA01533P BC

PMC21

PMP21

PMP23

FM IS Cl. I, Div.1 Gr. A-D T4 XA01321P FA

PMC21

PMP21

PMP23

CSA C/US IS Cl. I Div. 1 Gr. A-D XA01322P CB

PMC21

PMP21

PMP23

EAC Ex ia IIC T4 Ga/Gb XA01540P GA

PMC21

PMP21

PMP23

IEC Ex ia IIC T4 Ga/Gb XA01271P IA

PMC21

PMP21

PMP23

NEPSI Ex ia IIC T4 XA01363P NA

PMC21

PMP21

PMP23

TIIS Ex ia IIC T4 In preparation TA

1) Product Configurator, order code for "Approval"

The nameplate provides information on the Safety Instructions (XA) that are relevant

for the device.

Cerabar PMC11, PMC21, PMP11, PMP21, PMP23 Document information

Endress+Hauser 7

1.4 Terms and abbreviations

URL OPLMWP

LRL

LRV URV

A0029505

Item Term/

abbreviation

Explanation

1 OPL The OPL (over pressure limit = sensor overload limit) for the measuring device

depends on the lowest-rated element, with regard to pressure, of the selected

components, i.e. the process connection has to be taken into consideration in

addition to the measuring cell. Also observe pressure-temperature dependency. For

the relevant standards and additional notes, see the "Pressure specifications" section

→  44 .

The OPL may only be applied for a limited period of time.

2 MWP The MWP (maximum working pressure) for the sensors depends on the lowest-

rated element, with regard to pressure, of the selected components, i.e. the process

connection has to be taken into consideration in addition to the measuring cell.

Also observe pressure-temperature dependency. For the relevant standards and

additional notes, see the "Pressure specifications" section →  44 .

The MWP may be applied at the device for an unlimited period.

The MWP can also be found on the nameplate.

3 Maximum sensor

measuring range

Span between LRL and URL

This sensor measuring range is equivalent to the maximum calibratable/adjustable

span.

4 Calibrated/

adjusted span

Span between LRV and URV

Factory setting: 0 to URL

Other calibrated spans can be ordered as customized spans.

p - Pressure

- LRL Lower range limit

- URL Upper range limit

- LRV Lower range value

- URV Upper range value

- TD (turn down) Turn down

The turn down is preset at the factory and cannot be changed.

Example - see the following section.

Document information Cerabar PMC11, PMC21, PMP11, PMP21, PMP23

8 Endress+Hauser

1.5 Turn down calculation

LRV URLURV

LRL

1 = 2 3

A0029545

1 Calibrated/adjusted span

2 Zero point-based span

3 URL sensor

Example

• Sensor:10 bar (150 psi)

• Upper range value (URL) = 10 bar (150 psi)

Turn down (TD):

• Calibrated/adjusted span: 0 to 5 bar (0 to 75 psi)

• Lower range value (LRV) = 0 bar (0 psi)

• Upper range value (URV) = 5 bar (75 psi)

TD = URL

|URV - LRV|

TD = 10 bar (150 psi) = 2

|5 bar (75 psi) - 0 bar (0 psi)|

In this example, the TD is 2:1.

This span is based on the zero point.

Cerabar PMC11, PMC21, PMP11, PMP21, PMP23 Basic safety instructions

Endress+Hauser 9

2 Basic safety instructions

2.1 Requirements concerning the staff

The personnel for installation, commissioning, diagnostics and maintenance must fulfill

the following requirements:

‣Trained, qualified specialists: must have a relevant qualification for this specific

function and task

‣Are authorized by the plant owner/operator

‣Are familiar with federal/national regulations

‣Before beginning work, the specialist staff must have read and understood the

instructions in the Operating Instructions and supplementary documentation as well as

in the certificates (depending on the application)

‣Following instructions and basic conditions

The operating personnel must fulfill the following requirements:

‣Being instructed and authorized according to the requirements of the task by the

facility's owner-operator

‣Following the instructions in these Operating Instructions

2.2 Designated use

2.2.1 Application and media

The Cerabar is used to measure absolute and gauge pressure in gases, vapors and liquids.

The process-wetted materials of the measuring device must have an adequate level of

resistance to the media.

The measuring device may be used for the following measurements (process variables)

• in compliance with the limit values specified under "Technical data"

• in compliance with the conditions that are listed in additional documentation such as the

XA and this manual.

Measured process variable

• PMC11: gauge pressure

• PMP11: gauge pressure

• PMC21: gauge pressure or absolute pressure

• PMP21: gauge pressure or absolute pressure

• PMP23: gauge pressure or absolute pressure

Calculated process variable

Pressure

2.2.2 Incorrect use

The manufacturer is not liable for damage caused by improper or non-designated use.

Verification for borderline cases:

‣For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance

in verifying the corrosion resistance of process-wetted materials, but does not accept

any warranty or liability.

2.2.3 Residual risks

When in operation, the housing may reach a temperature close to the process

temperature.

Basic safety instructions Cerabar PMC11, PMC21, PMP11, PMP21, PMP23

10 Endress+Hauser

Danger of burns from contact with surfaces!

‣For elevated process temperatures, ensure protection against contact to prevent burns.

2.3 Workplace safety

For work on and with the device:

‣Wear the required personal protective equipment according to federal/national

regulations.

‣Switch off the supply voltage before connecting the device.

2.4 Operational safety

Risk of injury!

‣Operate the device in proper technical condition and fail-safe condition only.

‣The operator is responsible for interference-free operation of the device.

Conversions to the device

Unauthorized modifications to the device are not permitted and can lead to unforeseeable

dangers.

‣If, despite this, modifications are required, consult with Endress+Hauser.

Hazardous area

To eliminate the risk of danger to persons or the facility when the device is used in the

approval-related area (e.g. explosion protection, pressure equipment safety):

‣Check the nameplate to verify if the device ordered can be put to its intended use in the

approval-related area.

‣Observe the specifications in the separate supplementary documentation, such as the

XA or SD, which is an integral part of these Instructions.

2.5 Product safety

This measuring device is designed in accordance with good engineering practice to meet

state-of-the-art safety requirements, has been tested, and left the factory in a condition in

which it is safe to operate.

It meets general safety standards and legal requirements. It also complies with the EU

directives listed in the device-specific EU Declaration of Conformity. Endress+Hauser

confirms this by affixing the CE mark to the device.

Andere Handbücher für Cerabar PMC11

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Endress+Hauser Industrieanlagen Handbücher

Endress+Hauser

Endress+Hauser Fieldgate FXA720 Bedienungsanleitung

Endress+Hauser

Endress+Hauser SmarTec S CLD 132 PROFIBUS-PA Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiport 2000 Bedienungsanleitung

Endress+Hauser

Endress+Hauser 51517656 CleanFit H CPA 475 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA871 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Tankvision Multi Scan NXA83 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Soliwave FDR16 Technische Daten

Endress+Hauser

Endress+Hauser Micropilot FMR67 Firmware-Update

Endress+Hauser

Endress+Hauser Flowmeter Proline 500 Technische Daten

Endress+Hauser

Endress+Hauser CleanFit P CPA 471 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit H CPA475 Bedienungsanleitung

Endress+Hauser

Endress+Hauser TOC Analyzer CA78 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Tankvision Multi Scan NXA83 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit COA451 Bedienungsanleitung

Endress+Hauser

Endress+Hauser CleanFit P CPA 474 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Silopilot FMM50 Technische Daten

Endress+Hauser

Endress+Hauser CYR52 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Prothermo NMT 539 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiline Control CDC90 Technische Daten

Endress+Hauser

Endress+Hauser Kit CSF48 Bedienungsanleitung

Endress+Hauser

Endress+Hauser OUSTF10 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Stamoclean CAT430 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiline Control CDC90 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Analytik Jena CyBio Well vario Bedienungsanleitung

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

Siemens

Siemens 8MF1 Series Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

SCHUNK

SCHUNK VERO-S NSE-A3 138 Gebrauchsanweisung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung

ABB

ABB HT614003 Bedienungsanleitung