Endress+Hauser RIA15 Bedienungsanleitung

Operating Instructions

RIA15

Process display unit

Loop-powered 4 to 20 mA process display unit

BA01073K/09/EN/02.12

71207036

Valid as of version

01.00.xx

RIA15 Table of contents

Endress+Hauser 3

Table of contents

1 Important document

information ............. 4

1.1 Document function ............ 4

1.2 Document conventions .......... 4

2 Safety instructions ........ 6

2.1 Requirements for the personnel ..... 6

2.2 Designated use .............. 6

2.3 Workplace safety ............. 7

2.4 Operational safety ............. 7

2.5 Product safety ............... 7

3 Identification ............ 8

3.1 Nameplate ................. 8

3.2 Scope of delivery ............. 8

3.3 Certificates and approvals ........ 8

4 Installation .............. 9

4.1 Incoming acceptance, transport,

storage ................... 9

4.2 Installation conditions .......... 9

4.3 Installation instructions ......... 10

4.4 Post-installation check ......... 13

5 Wiring ................ 13

5.1 Quick wiring guide ........... 13

5.2 Inserting the cable, field housing .... 15

5.3 Connecting to potential equalization .. 16

5.4 Grounding ................ 16

5.5 Degree of protection ........... 17

5.6 Post-connection check ......... 17

6 Operation ............. 18

6.1 Operating functions ........... 19

7 Commissioning ......... 19

7.1 Post-installation check and switching

on the device .............. 19

7.2 Operating matrix ............ 19

8 Troubleshooting ......... 21

8.1 Error limits as per NAMUR ....... 21

8.2 Diagnostic messages ........... 22

8.3 Spare parts ................ 23

9 Maintenance ........... 23

10 Return ................ 23

11 Disposal ............... 24

12 Technical data .......... 24

Important document information RIA15

4 Endress+Hauser

1 Important document information

1.1 Document function

These Operating Instructions contain all the information that is required in various phases of

the life cycle of the device: from product identification, incoming acceptance and storage, to

mounting, connection, operation and commissioning through to troubleshooting, maintenance

and disposal.

1.2 Document conventions

1.2.1 Safety symbols

Symbol Meaning

DANGER

A0011189-EN

DANGER!

This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in

serious or fatal injury.

WARNING

A0011190-EN

WARNING!

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

serious or fatal injury.

CAUTION

A0011191-EN

CAUTION!

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or medium injury.

NOTICE

A0011192-EN

NOTICE!

This symbol contains information on procedures and other facts which do not result in

personal injury.

1.2.2 Electrical symbols

Symbol Meaning

A0011197

Direct current

A terminal to which DC voltage is applied or through which direct current flows.

A0011198

Alternating current

A terminal to which alternating voltage is applied or through which alternating current flows.

A0017381

Direct current and alternating current

• A terminal to which alternating voltage or DC voltage is applied.

• A terminal through which alternating current or direct current flows.

A0011200

Ground connection

A grounded terminal which, as far as the operator is concerned, is grounded via a grounding system.

A0011199

Protective ground connection

A terminal which must be connected to ground prior to establishing any other connections.

A0011201

Equipotential connection

A connection that has to be connected to the plant grounding system: This may be a potential

equalization line or a star grounding system depending on national or company codes of practice.

RIA15 Important document information

Endress+Hauser 5

1.2.3 Symbols for certain types of information

Symbol Meaning

A0011182

Allowed

Indicates procedures, processes or actions that are allowed.

A0011183

Preferred

Indicates procedures, processes or actions that are preferred.

A0011184

Forbidden

Indicates procedures, processes or actions that are forbidden.

A0011193

Tip

Indicates additional information.

A0011194

Reference to documentation

Refers to the corresponding device documentation.

A0011195

Reference to page

Refers to the corresponding page number.

A0011196

Reference to graphic

Refers to the corresponding graphic number and page number.

,…

Series of steps

ÃResult of a sequence of actions

A0013562

Help in the event of a problem

1.2.4 Symbols in graphics

Symbol Meaning

1, 2, 3,... Item numbers

,…

Series of steps

A, B, C, ... Views

A-A, B-B, C-C, ... Sections

A0013441

Flow direction

A0011187

Hazardous area

Indicates a hazardous area.

A0011188

Safe area (non-hazardous area)

Indicates a non-hazardous area.

Safety instructions RIA15

6 Endress+Hauser

1.2.5 Tool symbols

Symbol Meaning

A0011220

Flat blade screwdriver

A0011221

Allen key

A0011222

Open-ended wrench

A0013442

Torx screwdriver

2 Safety instructions

2.1 Requirements for the personnel

The personnel for installation, commissioning, diagnostics and maintenance must fulfill the

following requirements:

►Trained, qualified specialists must have a relevant qualification for this specific function and

task

►Are authorized by the plant owner/operator

►Are familiar with federal/national regulations

►Before beginning work, the specialist staff must have read and understood the instructions

in the Operating Instructions and supplementary documentation as well as in the

certificates (depending on the application)

►Following instructions and basic conditions

The operating personnel must fulfill the following requirements:

►Being instructed and authorized according to the requirements of the task by the facility's

owner-operator

►Following the instructions in these Operating Instructions

2.2 Designated use

The process display unit displays analog process variables on its screen.

The device is powered via the current loop and does not require an additional power supply.

RIA15 Safety instructions

Endress+Hauser 7

• The manufacturer accepts no liability for damages resulting from incorrect use or use other

than that designated. It is not permitted to convert or modify the device in any way.

• Panel-mounted device:

The device is designed for installation in a panel and must only be operated in an installed

state.

• Field device:

The device is designed for installation in the field.

•The device may only be operated under the permitted ambient conditions (® ä 25).

2.3 Workplace safety

For work on and with the device:

►Wear the required personal protective equipment according to federal/national regulations.

2.4 Operational safety

Risk of injury.

►Operate the device in proper technical condition and fail-safe condition only.

►The operator is responsible for interference-free operation of the device.

Conversions to the device

Unauthorized modifications to the device are not permitted and can lead to unforeseeable

dangers.

►If, despite this, modifications are required, consult with Endress+Hauser.

Repair

To ensure continued operational safety and reliability,

►Carry out repairs on the device only if they are expressly permitted.

►Observe federal/national regulations pertaining to repair of an electrical device.

►Use original spare parts and accessories from Endress+Hauser only.

Environmental requirements

If a plastic transmitter housing is permanently exposed to certain steam and air mixtures, this

can damage the housing.

►If you are unsure, please contact your Endress+Hauser Sales Center for clarification.

►If used in an approval-related area, observe the information on the nameplate.

2.5 Product safety

This measuring device is designed in accordance with good engineering practice to meet state-

of-the-art safety requirements, has been tested, and left the factory in a condition in which

they are safe to operate.

It meets general safety standards and legal requirements. It also complies with the EC

directives listed in the device-specific EC Declaration of Conformity. Endress+Hauser confirms

this by affixing the CE mark to the device.

Identification RIA15

8 Endress+Hauser

3 Identification

3.1 Nameplate

The nameplate is located on the right-hand side of the housing in the case of the field device,

and on the rear of the housing in the case of the panel-mounted device.

Ord. cd.: XXXXXXXX

Ser. no.: XXXXXXXXXXXXXXXXX

Ext. ord. cd.: RIA15-XXXXXXX

Ta= -40...+60°C

Front IP65 Type 4X Encl.

Loop powered 4...20 mA

Umax 30V Imax 100mA

RIA15

Made in Germany 2012

D-87484 Nesselwang

Class2 circuit or SELV circuit

A0018814

å 1 Nameplate of the process display unit (example)

1 Order code of the device 6 Approvals (optional)

2 Serial number of the device 7 Power supply

3 Manufacturer's address 8 Input signal

4 Ambient temperature range 9 Housing degree of protection

5 Device designation

3.2 Scope of delivery

The scope of delivery of the device comprises:

• Panel-mounted device

– Process display unit

– Operating Instructions

– Ex Safety Instructions (optional)

– Fastening fixtures

• Field device

– Process display unit

– Operating Instructions

– Ex Safety Instructions (optional)

– Fastening fixtures for wall/pipe mounting (optional)

– Weather protection cover (optional)

3.3 Certificates and approvals

An overview of all the approvals available is provided in the "Technical data" section.

CE mark, Declaration of Conformity

RIA15 Installation

Endress+Hauser 9

The device is designed to meet state-of-the-art safety requirements, has been tested, and left

the factory in a condition in which it is safe to operate. The device complies with the

applicable standards and regulations in accordance with EN 61010-1 "Safety requirements for

electrical equipment for measurement, control and laboratory use".

The device described in these Operating Instructions therefore complies with the statutory

requirements of the EU Directives. The manufacturer confirms that the device has been

successfully tested by applying the CE mark.

4 Installation

4.1 Incoming acceptance, transport, storage

Compliance with the permitted environmental and storage conditions is mandatory. Precise

specifications are provided in the "Technical data" section (® ä 24).

4.1.1 Incoming acceptance

On receipt of the goods, check the following points:

• Is the packaging or the content damaged?

• Is the delivery complete? Compare the scope of delivery against the information on your

order form.

4.1.2 Transport and storage

Please note the following:

• Pack the device so that is protected against impact for storage and transport. The original

packaging provides optimum protection.

• The permitted storage temperature is –40 to +85 °C (–40 to +185 °F); it is possible to store

the device at borderline temperatures for a limited period (48 hours maximum).

4.2 Installation conditions

At temperatures below –25 °C (–13 °F) the readability of the display can no longer be

guaranteed.

4.2.1 Display unit in the panel-mount housing

Permitted ambient temperature range –40 to 60 °C (–40 to 140 °F), horizontal orientation.

IP65 protection at front, IP20 at rear

See "Technical data" section (® ä 24).

4.2.2 Display unit in the field housing

Permitted ambient temperature range –40 to 60 °C (–40 to 140 °F). IP66 protection, NEMA

4x.

See "Technical data" section (® ä 24).

Installation RIA15

10 Endress+Hauser

4.3 Installation instructions

See the "Technical data" section for the dimensions of the device (® ä 27).

4.3.1 Panel housing

2mm

A0017762

å 2 Installation instructions for the panel housing

Installation in a panel with a panel cutout 92x45 mm (3.62x1.77 in.), max. panel thickness

13 mm (0.51 in).

1. Slot the device into the panel cutout from the front.

2. Fit the mounting clips on the side of the housing and tighten the threaded rods.

4.3.2 Field housing

Pipe mounting (with optional mounting kit)

The device can be mounted on a pipe with a diameter of up to 50.8 mm (2 in) with the

mounting kit (optionally available).

Andere Handbücher für RIA15

Inhaltsverzeichnis

Andere Endress+Hauser Messgerät Handbücher

Endress+Hauser

Endress+Hauser SS2100 Series Bedienungsanleitung

Endress+Hauser

Endress+Hauser CA76NA Bedienungsanleitung

Endress+Hauser

Endress+Hauser Memosens Wave CAS80E Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiphant S FDL60 Gebrauchsanweisung

Endress+Hauser

Endress+Hauser Proline Prowirl 200 Montageanleitung

Endress+Hauser

Endress+Hauser RID14 Bedienungsanleitung

Endress+Hauser

Endress+Hauser MODBUS RS485 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Stamolys CA71SI Series Bedienungsanleitung

Endress+Hauser

Endress+Hauser Soliphant T FTM20 Handbuch

Endress+Hauser

Endress+Hauser Proline 500 Technische Daten

Endress+Hauser

Endress+Hauser LT5 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Waterpilot FMX21 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiline System CA80HA Technische Daten

Endress+Hauser

Endress+Hauser Proline Promass F 200 HART Bedienungsanleitung

Endress+Hauser

Endress+Hauser Levelflex FMP51 Handbuch

Endress+Hauser

Endress+Hauser Levelflex M FMP40 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline 10 Technische Daten

Endress+Hauser

Endress+Hauser Micropilot S FMR540 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Bedienungsanleitung

Endress+Hauser

Endress+Hauser prosonic flow 92 Handbuch

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiline System CA80NO Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquicap T FMI21 Bedienungsanleitung

Endress+Hauser

Endress+Hauser EngyCal RH33 Technische Daten

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung