Endress+Hauser Liquiline M CM42 Bedienungsanleitung

Products Solutions Services

CM42-MAA101EBE00

BA00382C/07/EN/16.16

Valid as of:

Firmwareversion 02.02.00

Operating Instructions

Liquiline M CM42

Two-wire transmitter for pH/ORP measurement

with Memosens glass sensors

Part 2

Endress+Hauser

CM42-MAA101EBE00

Table of contents

1 Operation via the fieldbus . . . . 4

2 Calibration and adjustment . . . 5

2.1 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2 Terminology . . . . . . . . . . . . . . . . . . . . . . . . 5

2.3 Notes on the calibration . . . . . . . . . . . . . . 8

2.4 Calibration intervals . . . . . . . . . . . . . . . . . 8

2.5 Types of calibration . . . . . . . . . . . . . . . . . 10

2.6 Two-point calibration . . . . . . . . . . . . . . . 10

2.7 Single-point calibration . . . . . . . . . . . . . 11

2.8 Temperature adjustment . . . . . . . . . . . . 12

2.9 Calibrate . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3 Diagnostics, troubleshooting . 14

3.1 General troubleshooting . . . . . . . . . . . . . 14

3.2 Diagnostic information on local display 18

3.3 Diagnostic information via fieldbus . . . 22

3.4 Adapting the diagnostic information . . 22

3.5 Pending diagnostic messages . . . . . . . . . 23

3.6 Diagnostic list . . . . . . . . . . . . . . . . . . . . . . 23

3.7 Logbooks . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3.8 Simulation, Resetting the measuring device

3.9 Change sensor . . . . . . . . . . . . . . . . . . . . . 26

3.10 Sensor type change . . . . . . . . . . . . . . . . . 27

3.11 Sensor status . . . . . . . . . . . . . . . . . . . . . . 28

3.12 Output state . . . . . . . . . . . . . . . . . . . . . . . 29

3.13 Device information . . . . . . . . . . . . . . . . . 29

3.14 Sensor information . . . . . . . . . . . . . . . . . 29

3.15 Firmware history . . . . . . . . . . . . . . . . . . . 30

4 Maintenance. . . . . . . . . . . . . . . 31

5 Repair. . . . . . . . . . . . . . . . . . . . . 32

5.1 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . 32

5.2 Replacing modules . . . . . . . . . . . . . . . . . . 34

5.3 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

5.4 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

6 Accessories . . . . . . . . . . . . . . . . 35

6.1 Installation kits . . . . . . . . . . . . . . . . . . . . 36

6.2 Weather protection . . . . . . . . . . . . . . . . . 36

6.3 Firmware update and upgrade . . . . . . . . 36

6.4 Data management . . . . . . . . . . . . . . . . . . 36

6.5 Measured value simulation . . . . . . . . . . . 37

6.6 Communication-specific accessories . . . 37

7 Technical data. . . . . . . . . . . . . . 38

7.1 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

7.2 Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

7.3 Protocol-specific data . . . . . . . . . . . . . . . . 39

7.4 Electrical connection . . . . . . . . . . . . . . . . 40

7.5 Performance characteristics . . . . . . . . . . 41

7.6 Environment . . . . . . . . . . . . . . . . . . . . . . . 42

7.7 Mechanical construction . . . . . . . . . . . . . 42

Index. . . . . . . . . . . . . . . . . . . . . . 43

Operation via the fieldbus CM42-MAA101EBE00

4Endress+Hauser

1 Operation via the fieldbus

The device supports HART communication via current output 1. Here, digital data are

transmitted in addition to the current. Most process control systems have HART inputs that can

process the data further directly. Process values, the status of the process values and the device

status are transmitted.

The device can also be configured via HART. The device driver enables access to the complete

Setup and Diagnostics menu with few exceptions.

You have the following options for configuration:

• The process control system directly supports the use of DDs (Device Descriptions) and DTMs

(Device Type Managers) or

• you use an additional HART master, e.g. a handheld terminal or FieldCare in conjunction with

a modem.

The interface offered by the DDs and DTMs largely corresponds to the menu structure of local

operation.

It is not possible to access all the tables and the calibration with DDs or DTMs. In addition, it is

not possible to access the logbooks with a handheld terminal.

A detailed description of the commands and features supported by the device is provided in

SD01325C under "Document/Manuals/Software" and then "Special Documentation (SD)" on

www.endress.com/cm42.

CM42-MAA101EBE00 Calibration and adjustment

Endress+Hauser 5

2 Calibration and adjustment

The calibration provides important information on the condition of your sensor and the

quality of the pH measurement.

pH glass electrodes

In addition to the slope that has an ideal value of approx. -59 mV/pH at 25 °C, the change in the

zero point also provides important information to the user. It is an indicator of the condition of

the gel-like layer of the pH glass and could point to a blockage in the reference system. Suitable

maintenance would involve cleaning or regenerating the sensor.

To perform a quick test, simply immerse the sensor in a buffer solution with the same pH value

as the internal buffer (e.g. pH 7). 0 mV would be an ideal value. The greater the deviation from

the ideal value, the poorer the condition of the sensor (±20 mV is still acceptable in most

situations).

2.1 Definitions

Calibration (as per DIN 1319):

A calibration is defined as a set of operations that establish the relationship between the

measured value or expected value of the output variable and the related true or correct value of

the measured variable (input variable) for a measuring system under specified conditions.

A calibration does not alter the performance of the measuring device.

Adjustment

An adjustment corrects the value displayed by a measuring device, in other words the

measured/displayed value (the actual value) is corrected so that the reading agrees with the

correct, set value.

The value determined during calibration is used to calculate the correct measured value and

saved in the sensor.

2.2 Terminology

2.2.1 Zero point and slope

Using a mathematical function, the transmitter converts the input signal of the sensor y (raw

measured value) to the measured value x. In many cases, this function is a simple linear of the

form y = a + b .x.

The linear element "a" is usually equivalent to the zero point and the factor "b" is the slope of the

line and is often known as the sensor slope.

Calibration and adjustment CM42-MAA101EBE00

6Endress+Hauser

The Nernst equation, which is used to calculate the pH value, is a typical linear relationship:

pH = -lg(aH+), aH+ ... activity of the hydrogen ions

Ui... raw measured value in mV

U0... zero point (=voltage at pH 7)

R ... universal gas constant (8.3143 J/molK)

T ... temperature [K]

F ... Faraday constant (26.803 Ah/mol)

The slope of the Nernst equation (-2.303RT/F) is known as the Nernst factor and has the

value -59.16 mV/pH at 25 °C.

2.2.2 Delta slope

The device determines the difference in the slope between the calibration that is currently valid

and the last calibration. Depending on the sensor type, this difference is an indicator of the

condition of the sensor. The smaller the slope, the less sensitive the measurement, and the

accuracy deteriorates particularly in the low measuring range.

Depending on the operating conditions, users can define limit values that represent the still

tolerable absolute values of the slope and/or slope differentials. If the limit values are exceeded,

maintenance must be performed on the sensor at the very least. The sensor must be replaced if

the insensitivity problems persist after maintenance has been carried out.

a0013593

Fig. 1: Linear function

aZeropoint

bSlope

U=U

-2.303 RT

FpH

CM42-MAA101EBE00 Calibration and adjustment

Endress+Hauser 7

2.2.3 Delta zeropnt.

The device determines the difference between the zero points of the last and second-last

calibration. A shift in the zero point does not alter the sensitivity of the measurement. However,

if the offset is not corrected this can falsify the measured value.

As with the slope, you can also define and monitor limit values for the offset. If the limit values

are exceeded, this means that maintenance must be performed on the sensor.

a0013594

Fig. 2: Delta slope

Blue Last calibration

Red Calibration currently valid



bDeltaslope

a0013595

Fig. 3: Delta zeropnt.

a1 Zero point of the second-last calibration

a2 Zero point of the last calibration



aDeltazeropnt.

Calibration and adjustment CM42-MAA101EBE00

8Endress+Hauser

2.3 Notes on the calibration

The following rules apply for all parameters:

• Calibrate in a way that reflects conditions in the process.

– If the process medium is constantly moving, also move the calibration solution accordingly

(e.g. use a magnetic stirrer if calibrating in the laboratory).

– If your medium is relatively stationary, calibrate in solutions that are also stationary.

• Make sure that the samples are homogeneous for reference measurements, sample

calibration etc.

• Use the same menu settings as those in the process to perform the calibration.

Example: If you automatically compensate for the temperature effect during pH

measurement, switch on automatic temperature compensation for the calibration also.

It is advisable to perform the laboratory calibration using the "Memobase Plus" database

soware (→"Accessories"). This improves the availability of your measuring points and all

the calibration and sensor data records are stored securely in the database.

2.4 Calibration intervals

2.4.1 Specifying the intervals

The service life of a pH glass electrode is limited. This is due, in part, to the deterioration and

aging of the pH-sensitive membrane glass. This aging causes the gel-like layer to change and

become thicker over time.

Symptoms of aging include:

• Higher membrane resistance

• Slow response

• Decrease in the slope

A change in the reference system (e.g. due to contamination, i.e. unwanted redox reactions at

the reference electrode) or electrolyte solution dissolving away in the reference half cell can

change the reference potential, which, in turn, causes a zero point shift in the measuring

electrode.

To ensure a high level of accuracy, it is important to readjust the pH sensors at set intervals.

The calibration interval depends heavily on the area of application of the sensor, as well as the

required level of accuracy and reproducibility. The calibration interval can vary between daily

and once every few months.

Defining the calibration interval for the process

1. Check the sensor with a buffer solution, e.g. pH 7.

Proceed as specified in Step 2 only if the value deviates from the set point. No

calibration/adjustment is necessary if the value is within the defined deviation tolerance

range (see the Technical Information for the sensor).

2. Calibrate and adjust the sensor.

CM42-MAA101EBE00 Calibration and adjustment

Endress+Hauser 9

3. After 24 hours, check again with the buffer solution.

• If the deviation is within the permitted tolerance range, increase the checking interval

by doubling it for example.

• If the deviation is larger, you must shorten the interval.

4. Continue to proceed as defined in Steps 2 and 3 until you have identified the suitable

interval.

Monitoring the calibration

‣Define the limit values for monitoring the slope and zero point differentials (SETUP/Sensor

pH/ORP/Sensor diagnostics/Diagnostic limits).

These limit values depend on the process and must be determined by empirical means.

During calibration a diagnostics message is displayed if the defined warning limits have been

exceeded. You then have to service the sensor by cleaning the sensor or reference, or by

regenerating the glass membrane.

You have to replace the sensor if warning messages continue to be displayed despite the

maintenance measure.

2.4.2 Monitoring the calibration interval

If you have established calibration intervals for your process, you can also have the device

monitor them.

Two functions are available to monitor the calibration interval:

1. Calibration timer (SETUP/Sensor pH/ORP/Sensor diagnostics/Diagnostic limits/Calibration

timer)

You specify the calibration interval and the controller generates a diagnostics message

once the set time has elapsed. You then recalibrate the sensor or replace it with a

precalibrated sensor.

The timer is reset with the new calibration.

2. Calibration validity (SETUP/Sensor pH/ORP/Sensor diagnostics/Diagnostic

limits/Calibration expired)

You set time limits to specify how long a calibration should be regarded as valid.

Memosens sensors save all the calibration data. In this way it is easy to see whether the

last calibration took place in the specified timeframe and is therefore still valid. This is

particularly advantageous when working with precalibrated sensors.

Calibration and adjustment CM42-MAA101EBE00

10 Endress+Hauser

2.5 Types of calibration

2.5.1 pH measurement

The following types of calibration are possible:

• Two-point calibration

– With calibration buffers

– Entry of data for the slope, zero point and temperature

• Single-point calibration

– Entry of a reference value

– Sample calibration with laboratory comparative value

• Temperature adjustment by entering a reference value

If using a combined sensor (CPS16D/CPS76D/CPS96D) you must calibrate both the pH

electrode and the ORP electrode to get reliable rH values, for example.

2.5.2 Measuring the ORP

The following types of calibration are possible:

• Two-point calibration with medium samples (only ORP %)

• Single-point calibration with calibration buffer (only ORP mV)

• Data entry of an offset (only ORP mV)

• Temperature adjustment via reference value

2.6 Two-point calibration

2.6.1 General information

Two-point calibration is the preferred method for pH sensors, particularly in the following

applications:

• Municipal and industrial wastewater

• Natural waters and drinking water

• Boiler feedwater and condensates

• Beverages

Calibrating with buffers with pH 7.0 and 4.0 is recommended for most applications.

Alkaline buffer solutions have the disadvantage that carbon dioxide from the air can alter the

pH value of the buffer on the long term. If calibrating with alkaline buffers it is best to do so in

closed systems, such as flow assemblies or retractable assemblies with a rinse chamber, to

minimize the effect of air.

2.6.2 With calibration buffers

pH measurement

You use calibration buffers to perform two-point calibration. The quality buffers supplied

by Endress+Hauser are certified and measured in an accredited laboratory. The

Andere Handbücher für Liquiline M CM42

Inhaltsverzeichnis

Andere Endress+Hauser Messgerät Handbücher

Endress+Hauser

Endress+Hauser Proline Promass X 500 FOUNDATION Fieldbus Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promass 83 Montageanleitung

Endress+Hauser

Endress+Hauser Proline Promag 10 Bedienungsanleitung

Endress+Hauser

Endress+Hauser prowirl 77 Bedienungsanleitung

Endress+Hauser

Endress+Hauser RIA 250 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promass 300 Bedienerhandbuch

Endress+Hauser

Endress+Hauser Deltabar S PMD75 Technische Daten

Endress+Hauser

Endress+Hauser Cerabar M Bedienungsanleitung

Endress+Hauser

Endress+Hauser Dosimag Bedienungsanleitung

Endress+Hauser

Endress+Hauser Memocheck Sim CYP03D Bedienungsanleitung

Endress+Hauser

Endress+Hauser Levelflex M FMP43 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Flexdip CYA112 Bedienungsanleitung

Endress+Hauser

Endress+Hauser PROFIBUS-PA PROline promass 80 Technische Daten

Endress+Hauser

Endress+Hauser Prosonic S FMU90 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiline System CA80AM Technische Daten

Endress+Hauser

Endress+Hauser Solicap M FTI56 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Prosonic Flow B 200 Bedienungsanleitung

Endress+Hauser

Endress+Hauser promag 50 PROFIBUS-PA Technische Daten

Endress+Hauser

Endress+Hauser Cubemass DCI Bedienungsanleitung

Endress+Hauser

Endress+Hauser nivotester FTC 420 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag H 200 Handbuch

Endress+Hauser

Endress+Hauser Proline Prosonic Flow 93 Stücklistenhandbuch

Endress+Hauser

Endress+Hauser StamoLys CA 71 CR Bedienungsanleitung

Endress+Hauser

Endress+Hauser Solicap M FTI55 Montageanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung

Uniks

Uniks C126 Bedienungsanleitung