Equinox Systems MaxiPar Tri MKII Bedienungsanleitung

Order code: EQLED111A

MaxiPar Tri MKII

User Manual

www.prolight.co.uk MaxiPar Tri MKII User Manual 2

Safety advice

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL

CAREFULLY BEFORE YOUR INITIAL START-UP!

• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.

• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.

• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary

fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.

• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance

of this manual or any unauthorised modication to the equipment.

OPERATING DETERMINATIONS

Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand

thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.

Donotendangeryourownsafetyandthesafetyofothers!

Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.

• Neverletthepowercablecomeintocontactwithother

cables.Handlethepowercableandallmainsvoltage

connectionswithparticularcaution!

• Neverremovewarningorinformativelabelsfromtheunit.

• Donotopentheequipmentanddonotmodifytheunit.

• Donotconnectthisequipmenttoadimmerpack.

• Donotswitchtheequipmentonandoffinshortintervals,

asthiswillreducethesystem’slife.

• Onlyusetheequipmentindoors.

• Donotexposetoammablesources,liquidsorgases.

• Alwaysdisconnectthepowerfromthemainswhen

equipmentisnotinuseorbeforecleaning!Onlyhandle

thepower-cablebytheplug.Neverpullouttheplugby

pullingthepower-cable.

• Makesurethattheavailablevoltageisbetween

100~240V,50/60Hz.

• Makesurethatthepowercableisnevercrimpedor

damaged.Checktheequipmentandthepowercable

periodically.

• Iftheequipmentisdroppedordamaged,disconnectthe

mainspowersupplyimmediatelyandhaveaqualied

engineerinspecttheequipmentbeforeoperatingagain.

• Iftheequipmenthasbeenexposedtodrastic

temperatureuctuation(e.g.aftertransportation),

donotconnectpowerorswitchitonimmediately.

Thearisingcondensationmightdamagetheequipment.

Leavetheequipmentswitchedoffuntilithasreached

roomtemperature.

• Ifyourproductfailstofunctioncorrectly,stopuse

immediately.Packtheunitsecurely(preferablyinthe

originalpackingmaterial),andreturnittoyourProLight

dealerforservice.

• Onlyusefusesofsametypeandrating.

• Repairs,servicingandpowerconnectionmustonlybe

carriedoutbyaqualiedtechnician.THISUNITCONTAINS

NOUSERSERVICEABLEPARTS.

• WARRANTY:Oneyearfromdateofpurchase.

CAUTION!

KEEP THIS EQUIPMENT

AWAY FROM RAIN,

MOISTURE AND LIQUIDS

CAUTION!

TAKE CARE USING

THIS EQUIPMENT!

HIGH VOLTAGE-RISK

OF ELECTRIC SHOCK!!

www.prolight.co.uk MaxiPar Tri MKII User Manual 3

Product overview & technical specications

Thiscompact,slimproleparisdesignedforuplightingaswellasstagelighting,andwillbringdeep,

richcolourstoanyeventorvenue.Itfeatures12x3Wtri-colourRGBLEDswhichoffersmoothcolourmixing.

OperationalmodesincludingDMX,auto,soundactiveandmaster/slavemodes.

•12x3Wtri-colourLEDs(RGB)

•Beamangle:25°

•2,106Lux@2m(fullon)

•DMXchannels:3or6selectable

•Auto,soundactiveand

master/slavemodes

•0-100%dimmingand

variablestrobe

•4pushbuttonmenu

withLEDdisplay

•Bracketallowsformultiplerigging

oroorstandingapplications

•Rubberfeetallowthepanel

tositatontheoorforuplighting

•SideentryXLRand

powerconnections

•IECpowerinput/output

•3-PinXLRinput/output

•Fancooled

MaxiPar Tri MKII

Specications

Powerconsumption 40W

Powersupply 100~240V,50/60Hz

Fuse T1A250V

Dimensions 205x225x115mm

Weight 0.85kg

Ordercode EQLED111A

205mm

225mm 115mm

0m 1m 2m 3m 4m 5m

25° - Lux

FULL ON

8440

1960

5600

400

2106

491

1402

100

983

218

622

44.4

25°

528

123

350

338

78.6

224

TRI MKII

MAXIPAR

DOWNUP

MIC

MENU ENTER

www.prolight.co.uk

POWER OUTPUT:

100-240V~50/60Hz

DMX OUTPUT

POWER INPUT:

100-240V~50/60Hz

FUSE: T1A 250V

DMX INPUT

POWER CONSUMPTION: 40W

0907

TRI MKII

MAXIPAR

DOWNUP

MIC

MENU ENTER

www.prolight.co.uk

POWER OUTPUT:

100-240V~50/60Hz

DMX OUTPUT

POWER INPUT:

100-240V~50/60Hz

FUSE: T1A 250V

DMX INPUT

POWER CONSUMPTION: 40W

02 02

01 01

01-Bracket

02-Bracketknobs

03-LEDdisplay

04-Functionbuttons

05-Microphone

06-DMXinputsocket

07-DMXoutputsocket

08-IECpowerinputsocket

09-IECpoweroutputsocket

10-FuseT1A250V

Inthebox:1 x xture,

1 x power cable &

1 x user manual

www.prolight.co.uk MaxiPar Tri MKII User Manual 4

Operating instructions

S L A V

Slave mode

A 0 0 1

A 5 1 2

DMX settings

A d d r

6 C H

3 C H

Built in programs

P r - -

r 0 0 1

g 0 0 1

r 2 5 5

g 2 5 5

b 0 0 1 b 2 5 5

Colour mix mode

P r 1 3

P r 0 1

P r 0 0

0 0 0

1 0 0

Sound settings

S O U d S E n S

www.prolight.co.uk MaxiPar Tri MKII User Manual 5

Operating instructions

DMX mode:

OperatinginaDMXcontrolmodeenvironmentgivestheuserthegreatestexibilitywhenitcomes

tocustomisingorcreatingashow.Inthismodeyouwillbeabletocontroleachindividualtraitof

thextureandeachxtureindependently.

ToaccesstheDMXmode,pressthe“MENU”buttonandusethe“UP”and“DOWN”buttonstoshow

AddrontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonsto

chooseoneofthe3or6DMXchannelmodes.

Pressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstosettherequiredDMXaddress.

Pressthe“ENTER”buttontoconrmthesetting.

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

6 channel mode:

Channel Value Function

CH1 000-255 Reddimmer(0-100%)

CH2 000-255 Greendimmer(0-100%)

CH3 000-255 Bluedimmer(0-100%)

CH4

000-027 Nofunction

028-055 Strobe(useCH6forspeed)

056-083 Strobewithcolourchange

(useCH6forspeed)

084-111 Red

112-139 Green

140-167 Blue

168-195 Yellow

196-223 Purple

224-251 Cyan

252-255 White

CH5

000 Nofunction

001-012 Redfadein/out

(useCH6

forspeed)

013-025 Greenfadein/out

026-038 Bluefadein/out

039-051 Yellowfadein/out

052-064 Purplefadein/out

065-077 Cyanfadein/out

078-090 Whitefadein/out

091-116 Autocolourfadein/out

117-142 Colourfade

143-168 Colourchange

169-181 Colourchangewithstrobe

182-207 Allautoshows

208-255 Soundactiveash(whenCH6is000)

208-255 Soundactive(whenCH6is001-255)

CH6 000-255 Speed(slow-fast)/Sensitivity(low-high)

3 channel mode:

Channel Value Function

CH1 000-255 Reddimmer(0-100%)

CH2 000-255 Greendimmer(0-100%)

CH3 000-255 Bluedimmer(0-100%)

www.prolight.co.uk MaxiPar Tri MKII User Manual 6

RGB colour mix mode:

Inthismodeyoucansetthexturetoanycolourandanybrightness.

Toaccessthecolourmixmodepress“MENU”untilthedisplayshowsPr--ontheLEDdisplay.

Pressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstoselectPr00.

Pressthe“ENTER”buttontoshow r---with3digitsafterontheLEDdisplay.

Pressthe“ENTER”buttontoconrm.

Therrepresentsred,G=greenandb=blue.

The3digitsafterarethebrightnesssettingfrom000~255.

For example:

Ifyousetr,G,balltozero,yourunitwillhavenoLEDslitup(blackout).

Ifyousetr000tor255andGandbtozero,yourunitwillshowonlyredLEDs.

Pressthe“ENTER”buttontoconrmthesettingandmovetothenextcolour.

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

Built-in program mode:

Toaccessbuilt-inprogrammodepress“MENU”untilthedisplayshowsPr--ontheLEDdisplay.

Pressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstoselectbetweenPr00~Pr13.

Pressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstoselectthespeedbetween

SP00~Sp20.Pressthe“ENTER”buttontoconrm.

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

Sound active mode:

Toaccessthesoundactivemode,pressthe“MENU”buttononthefrontoftheunittoshowSoudon

theLEDdisplay.Nowpressthe“ENTER”buttonandthedisplaywillshowSens.Pressthe“ENTER”

buttonagainandusethe“UP”and“DOWN”buttonstoselectthesensitivitylevelfrom000-100.

Pressthe“ENTER”buttontoconrmthesetting.

Value: 000 - 100 (000 = low,100 = high)

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

Master/slave mode:

Tosetthemasterunit,pressthe“MENU”buttonontherearofthemasterunittoselectyour

desiredprogram(soundactiveorRGBcolourmix).

Tosettheotherunitsinslavemode,pressthe“MENU”buttonontherearoftheunittoshowSLav

ontheLEDdisplayandpressthe“ENTER”buttontoconrmthesetting.Theunitswillnowrunin

sequencewiththemasterunit.

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

www.prolight.co.uk MaxiPar Tri MKII User Manual 7

Setting the DMX address:

TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”

from1-512.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel

indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas

addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105

and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe

chainstartsat107.

DMX 512:

DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent

xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.

DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”

XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).

DMX linking:

DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether

andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.

ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest

cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe

DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein

aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda

DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,

nomatterwhereitislocatedintheDMXchain.

DATA cable (DMX cable) requirements (for DMX operation):

ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.

YourunitandyourDMXcontrollerrequireastandard3-pinXLRconnectorfordatainput/output,

seeimagebelow.

Also remember that DMX cable must be daisy chained and cannot be split.

DMX setup

FurtherDMXcablescanbe

purchasedfromallgoodsound

andlightingsuppliersor

ProLightConceptsdealers.

Pleasequote:

CABL10 – 2m

CABL11 – 5m

CABL12 – 10m

www.prolight.co.uk MaxiPar Tri MKII User Manual 8

Notice:

Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables

shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs

outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.

Special note:

Line termination:

Whenlongerrunsofcableareused,

youmayneedtouseaterminatoron

thelastunittoavoiderraticbehaviour.

Using a cable terminator will decrease

the possibilities of erratic behaviour.

(3-pin - Order ref: CABL90, 5-pin - Order ref: CABL89)

5-pin XLR DMX connectors:

Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures

maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa

3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.

Terminationreducessignaltransmission

problemsandinterference.itisalways

advisabletoconnectaDMXterminal,

(resistance120Ohm1/4W)betweenpin2

(DMX-)andpin3(DMX+)ofthelastxture.

5-pin XLR (female)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

3-pin XLR (female)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

3-pin XLR (male)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

5-pin XLR (male)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

DMX setup

www.prolight.co.uk MaxiPar Tri MKII User Manual 9

WEEE notice

Correct Disposal of this Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries

with separate collection systems)

Thismarkingshownontheproductoritsliterature,indicatesthatitshouldnotbedisposedof

withotherhouseholdwastesattheendofitsworkinglife.Topreventpossibleharmtothe

environmentorhumanhealthfromuncontrolledwastedisposal,pleaseseparatethisfromother

typesofwastesandrecycleitresponsiblytopromotethesustainablereuseofmaterialresources.

Householdusersshouldcontacteithertheretailerwheretheypurchasedthisproduct,ortheir

localgovernmentofce,fordetailsofwhereandhowtheycantakethisitemforenvironmentally

saferecycling.

Businessusersshouldcontacttheirsupplierandcheckthetermsandconditionsofthe

purchasecontract.Thisproductshouldnotbemixedwithothercommercialwastesfordisposal.

www.prolight.co.uk MaxiPar Tri MKII User Manual 10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Equinox Systems DJ-Equipment Handbücher

Equinox Systems

Equinox Systems Truss Booth LED Starcloth System CW MKII Bedienungsanleitung

Equinox Systems

Equinox Systems Micro Batt EQLED160 Bedienungsanleitung

Equinox Systems

Equinox Systems Stratos Wash RGBA Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED127 Bedienungsanleitung

Equinox Systems

Equinox Systems PRO DJ Booth LED Starcloth System Bedienungsanleitung

Equinox Systems

Equinox Systems Power Par 54 MKIII Bedienungsanleitung

Equinox Systems

Equinox Systems Microbor EQLED60 Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED135 Bedienungsanleitung

Equinox Systems

Equinox Systems FUSION SPOT XP MKIII Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED162 Installations- und Betriebshandbuch

Equinox Systems

Equinox Systems Beamtastic Bedienungsanleitung

Equinox Systems

Equinox Systems PFM1500 Bedienungsanleitung

Equinox Systems

Equinox Systems MoonPar Bedienungsanleitung

Equinox Systems

Equinox Systems FXbar18 Bedienungsanleitung

Equinox Systems

Equinox Systems Midas Spot Bedienungsanleitung

Equinox Systems

Equinox Systems Pulse Tube Lithium Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED53 Bedienungsanleitung

Equinox Systems

Equinox Systems CARBON Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED136 Bedienungsanleitung

Equinox Systems

Equinox Systems TAURUS Bedienungsanleitung

Equinox Systems

Equinox Systems FEVER Bedienungsanleitung

Equinox Systems

Equinox Systems HYPE Bedienungsanleitung

Equinox Systems

Equinox Systems Hot Rod EQLED089 Bedienungsanleitung

Equinox Systems

Equinox Systems Helix Scan XP 150W Scanner Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung