Equinox Systems Domin8R II Bedienungsanleitung

Order code: EQLED53

Domin8R II

User Manual

www.prolight.co.uk Domin8R II User Manual 2

Safety advice

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL

CAREFULLY BEFORE YOUR INITIAL START-UP!

• Before your initial start-up, please make sure that there is no damage caused during transportation.

• Should there be any damage, consult your dealer and do not use the equipment.

• To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

• Please note that damages caused by user modications to this equipment are not subject to warranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance

of this manual or any unauthorised modication to the equipment.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and

the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and/or property.

Please note: These xtures are intended for stage lighting and entertainment applications only, and are not intended for

extended periods of use, including but not limited to house-light, industrial or architectural applications and should only be

operated with short duty cycles.

CAUTION!

KEEP THIS EQUIPMENT

AWAY FROM RAIN,

MOISTURE AND LIQUIDS

CAUTION!

TAKE CARE USING

THIS EQUIPMENT!

HIGH VOLTAGE-RISK

OF ELECTRIC SHOCK!!

• Never let the power cable come into contact with other

cables. Handle the power cable and all mains voltage

connections with particular caution!

• Never remove warning or informative labels from the unit.

• Do not open the equipment and do not modify the unit.

• Do not connect this equipment to a dimmer pack.

• Do not switch the equipment on and off in short intervals,

as this will reduce the system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when

equipment is not in use or before cleaning! Only handle

the power-cable by the plug. Never pull out the plug by

pulling the power-cable.

• Make sure that the available mains supply voltage is

between 100~240V AC, 50/60Hz.

• Make sure that the power cable is never crimped or

damaged. Check the equipment and the power cable

periodically.

• If the equipment is dropped or damaged, disconnect the

mains power supply immediately and have a qualied

engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic

temperature uctuation (e.g. after transportation),

do not connect power or switch it on immediately.

The arising condensation might damage the equipment.

Leave the equipment switched off until it has reached

room temperature.

• If your product fails to function correctly, stop use

immediately. Pack the unit securely (preferably in the

original packing material), and return it to your Pro Light

dealer for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be

carried out by a qualied technician. THIS UNIT CONTAINS

NO USER SERVICEABLE PARTS.

• This lighting xture is for professional use only - it is

not designed for or suitable for household use. The

product must be installed by a qualied technician in

accordance with local territory regulations. The safety of

the installation is the responsibility of the installer. The

xture presents risks of severe injury or death due to re

hazards, electric shock and falls.

• Warning! Risk Group 2 LED product according to

EN 62471. Do not view the light output with optical

instruments or any device that may concentrate the beam.

• WARRANTY: One year from date of purchase.

www.prolight.co.uk Domin8R II User Manual 3

MIC

DMX IN DMX OUT

POWER IN/OUT:

100~240V, 50/60Hz

SENSITIVITY

MIN MAX

MENU DOWN UP ENTER

FUSE:

F3A 250V

Product overview & technical specications

Taking the light show in one box to a new level is the Domin8R. The xture has a robust metal housing and

features 8 mirrors and 120 LEDs. This innovative effect will shoot penetrating, coloured beams of light over

long distances and is great for producing aerial effects over crowds.

• 120 x 5mm LEDs (R: 40, G: 40, B: 40)

• DMX channels: 8 or 16 selectable

• Sound active, auto and master/slave modes

• Supplied with hanging bracket

• IEC power input/output

• 3-Pin XLR input/output

Domin8R II

Specications

Power consumption 84W

Power supply 100~240V, 50/60Hz

Fuse F3A 250V

Dimensions 320 x 900 x 110mm

Weight 8.8kg

Order codes EQLED53

320mm

225mm

900mm 110mm

01 - Hanging bracket

02 - Hanging bracket

adjustment knob

03 - LED display

04 - Function buttons

05 - Sound sensitivity

adjustment

06 - Microphone

07 - IEC power input

08 - IEC power output

09 - 3-Pin XLR DMX input

10 - 3-Pin XLR DMX output

11 - Fuse: F3A 250V

12 - Safety eye

13 - Earth point

In the box: 1 x xture,

1 x power cable

& 1 x user manual

01 12

MIC

DMX IN DMX OUT

POWER IN/OUT:

100~240V, 50/60Hz

SENSITIVITY

MIN MAX

MENU DOWN UP ENTER

FUSE:

F3A 250V

0605

08 10

www.prolight.co.uk Domin8R II User Manual 4

DMX mode:

Operating in a DMX control mode environment gives the user the greatest exibility when it comes to

customising or creating a show. In this mode you will be able to control each individual trait of the

xture and each xture independently.

To select the DMX address, press the “MENU” button on the rear of the unit to show Addr on the

LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to select the DMX

address between 001-512. Press the “ENTER” button to conrm the setting.

To access the DMX channel mode, press the “MENU” button on the rear of the unit to show CHNd.

Now press the “ENTER” button and use the “UP” and “DOWN” buttons to select between the 8 and 16

channels. Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

Technical specications

8 channel mode:

Channel Value Function

1 000-127 No function

128-255 On

2 000-255 Strobe (slow-fast)

3 000-255 Static pattern selector

4 000-255 Moving pattern selector

5 000-127 Static pattern

128-255 Moving pattern

6 000-255 Moving pattern speed (slow-fast)

7 000-127 Manual mirror tilt

128-255 Auto mirror tilt (up and down)

8 000-255 Mirror tilt speed

16 channel mode:

Channel Value Function

1 000-127 No function

128-255 On

2 000-255 Strobe (slow-fast)

3 000-255 Static pattern selector

4 000-255 Moving pattern selector

5 000-127 Static pattern

128-255 Moving pattern

6 000-255 Moving pattern speed (slow-fast)

7 000-127 Manual mirror 1 tilt

128-255 Auto mirror 1 tilt (up and down)

8 000-127 Manual mirror 2 tilt

128-255 Auto mirror 2 tilt (up and down)

9 000-127 Manual mirror 3 tilt

128-255 Auto mirror 3 tilt (up and down)

10 000-127 Manual mirror 4 tilt

128-255 Auto mirror 4 tilt (up and down)

11 000-127 Manual mirror 5 tilt

128-255 Auto mirror 5 tilt (up and down)

12 000-127 Manual mirror 6 tilt

128-255 Auto mirror 6 tilt (up and down)

13 000-127 Manual mirror 7 tilt

128-255 Auto mirror 7 tilt (up and down)

14 000-127 Manual mirror 8 tilt

128-255 Auto mirror 8 tilt (up and down)

15 000-255 Mirror tilt speed (slow-fast)

16 000-127 No function

000-128 Sound active

DMX mode 8CH, 16CH

Address setting d001~d512

Master/Slave mode NASt

SLA1

SLA2

Sound active mode SOUN

LED timeout LEd

Display dISP

dSIp

Test test

Hours hour

Menu system

www.prolight.co.uk Domin8R II User Manual 5

Operating instructions

Master/slave mode:

To set the master unit, press the “MENU” button on the rear of the master unit to show SLNd on

the LED display. Press the “ENTER” button and use the “UP” and “DOWN” buttons to select Nast.

Press the “ENTER” button to conrm the setting and then select your desired program.

To set the other units in slave mode, press the “MENU” button on the rear of the unit to show SLNd

on the LED display. Press the “ENTER” button and use the “UP” and “DOWN” buttons to select either

sLa1 (Slave mode 1) or sLa2 (Slave mode 2). Press the “ENTER” button to conrm the setting.

The units will now run in sequence with the master unit.

Slave mode 1 - This is the mormal slave mode and will copy the master unit.

Slave mode 2 - This is the slave inversion mode where the slave unit(s) will move in the opposite

direction from the master unit.

To exit out of any of the above options, press the “MENU” button.

Please ensure that all slave units are set to the same DMX channel mode as the master unit.

Sound active mode:

To access sound active mode press the “MENU” button until the display shows SOUN on the

LED display. Press “ENTER” to conrm the setting. Use the “UP” and “DOWN” buttons to set sound ac-

tive mode to on or off. Press the “ENTER” button to conrm the setting. To adjust the sound sensi-

tivity use the sound sensitivity adjustment knob on the rear of the unit.

To exit out of any of the above options, press the “MENU” button.

Please note: When there is no sound present the unit will automatically switch to slow auto run

LED display timout:

To access LED display timeout press the “MENU” button until the display shows Led on the

LED display. Press “ENTER” to conrm the setting. Use the “UP” and “DOWN” buttons to selewct

between on or off. Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

Display mode:

To access the display mode, press the “MENU” button on the rear of the unit to show dISP on the

LED display. To lp the display press the “ENTER” button and use the “UP” and “DOWN” buttons to

select dSIP. Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MODE” button.

Test mode:

To test that all the LEDs are illuminating, press the “MENU” button on the rear of the unit to show

test on the LED display. Press the “ENTER” button to start the test. Once you are satised with the

test press the “ENTER” button to stop it.

To exit out of any of the above options, press the “MODE” button.

Operating instructions

www.prolight.co.uk Domin8R II User Manual 6

Setting the DMX address:

The DMX mode enables the use of a universal DMX controller. Each xture requires a “start address”

from 1- 512. A xture requiring one or more channels for control begins to read the data on the channel

indicated by the start address. For example, a xture that occupies or uses 7 channels of DMX and was

addressed to start on DMX channel 100, would read data from channels: 100,101,102,103,104,105

and 106. Choose a start address so that the channels used do not overlap. E.g. the next unit in the

chain starts at 107.

DMX 512:

DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent

xtures and controllers. A DMX controller sends DMX data instructions form the controller to the xture.

DMX data is sent as serial data that travels from xture to xture via the DATA “IN” and DATA “OUT”

XLR terminals located on all DMX xtures (most controllers only have a data “out” terminal).

DMX linking:

DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all xtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX xtures try to use the shortest

cable path possible. The order in which xtures are connected in a DMX line does not inuence the

DMX addressing. For example; a xture assigned to a DMX address of 1 may be placed anywhere in

a DMX line, at the beginning, at the end, or anywhere in the middle. When a xture is assigned a

DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit,

no matter where it is located in the DMX chain.

DATA cable (DMX cable) requirements (for DMX operation):

This xture can be controlled via DMX-512 protocol. The DMX address is set on the back of the unit.

Your unit and your DMX controller require a standard 3-pin XLR connector for data input/output,

see image below.

Also remember that DMX cable must be daisy chained and cannot be split.

DMX setup

Further DMX cables can be

purchased from all good sound

and lighting suppliers or

Pro Light Concepts dealers.

Please quote:

CABL10 – 2m

CABL11 – 5m

CABL12 – 10m

www.prolight.co.uk Domin8R II User Manual 7

Notice:

Be sure to follow the diagrams below when making your own cables. Do not connect the cables

shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs

outer casing. Grounding the shield could cause a short circuit and erratic behaviour.

Special note:

Line termination:

When longer runs of cable are used,

you may need to use a terminator on

the last unit to avoid erratic behaviour.

Using a cable terminator will decrease

the possibilities of erratic behaviour.

(3-pin - Order ref: CABL9O, 5-pin - Order ref: CABL89)

5-pin XLR DMX connectors:

Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-pin XLR xtures

may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a

3-pin line a cable adaptor must be used. The diagram below details the correct cable conversion.

Termination reduces signal transmission

problems and interference. It is always

advisable to connect a DMX terminal,

(resistance 120 Ohm 1/4 W) between pin 2

(DMX-) and pin 3 (DMX+) of the last xture.

5-pin XLR (female)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

3-pin XLR (female)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

3-pin XLR (male)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

5-pin XLR (male)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

DMX setup

www.prolight.co.uk Domin8R II User Manual 8

Operating instructions & WEEE notice

Correct Disposal of this Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries

with separate collection systems)

This marking shown on the product or its literature, indicates that it should not be disposed of

with other household wastes at the end of its working life. To prevent possible harm to the

environment or human health from uncontrolled waste disposal, please separate this from other

types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their

local government ofce, for details of where and how they can take this item for environmentally

safe recycling.

Business users should contact their supplier and check the terms and conditions of the

purchase contract. This product should not be mixed with other commercial wastes for disposal.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Equinox Systems DJ-Equipment Handbücher

Equinox Systems

Equinox Systems Stratos Duo RGB Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED003 Bedienungsanleitung

Equinox Systems

Equinox Systems MIRR22 Bedienungsanleitung

Equinox Systems

Equinox Systems Confetti Burst EQLED400 Bedienungsanleitung

Equinox Systems

Equinox Systems Triton Beam EQLED071 Bedienungsanleitung

Equinox Systems

Equinox Systems PRO DJ Booth Quad-colour Starcloth Bedienungsanleitung

Equinox Systems

Equinox Systems TAURUS Bedienungsanleitung

Equinox Systems

Equinox Systems FEVER Bedienungsanleitung

Equinox Systems

Equinox Systems Waterwave 50W Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED368 Bedienungsanleitung

Equinox Systems

Equinox Systems Power Par 54 MKII Bedienungsanleitung

Equinox Systems

Equinox Systems HYPE Bedienungsanleitung

Equinox Systems

Equinox Systems Six Shooter MKII Bedienungsanleitung

Equinox Systems

Equinox Systems Waterwave XP Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED162 Installations- und Betriebshandbuch

Equinox Systems

Equinox Systems Micro Batt EQLED160 Bedienungsanleitung

Equinox Systems

Equinox Systems SpectraPix Batten Bedienungsanleitung

Equinox Systems

Equinox Systems Midas Spot Bedienungsanleitung

Equinox Systems

Equinox Systems FUSION SPOT XP MKIII Bedienungsanleitung

Equinox Systems

Equinox Systems Truss Booth LED Starcloth System CW MKII Bedienungsanleitung

Equinox Systems

Equinox Systems CARBON Bedienungsanleitung

Equinox Systems

Equinox Systems MaxiPar Quad Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED064 Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED53 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung