Equinox Systems Truss Booth LED Starcloth System CW MKII Bedienungsanleitung

Order code: EQLED150B

Truss Booth LED

Starcloth System, CW

MKII

User Manual

www.prolight.co.uk Truss Booth LED Starcloth System, CW MKII

User Manual 2

Safety advice

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL

CAREFULLY BEFORE YOUR INITIAL START-UP!

• Before your initial start-up, please make sure that there is no damage caused during transportation.

• Should there be any damage, consult your dealer and do not use the equipment.

• To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

• Please note that damages caused by user modications to this equipment are not subject to warranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance

of this manual or any unauthorised modication to the equipment.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and

the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and/or property.

CAUTION!

KEEP THIS EQUIPMENT

AWAY FROM RAIN,

MOISTURE AND LIQUIDS

CAUTION!

TAKE CARE USING

THIS EQUIPMENT!

HIGH VOLTAGE-RISK

OF ELECTRIC SHOCK!!

• Never let the power cable come into contact with other

cables. Handle the power cable and all mains voltage

connections with particular caution!

• Never remove warning or informative labels from the unit.

• Do not open the equipment and do not modify the unit.

• Do not connect this equipment to a dimmer pack.

• Do not switch the equipment on and off in short intervals,

as this will reduce the system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when

equipment is not in use or before cleaning! Only handle

the power-cable by the plug. Never pull out the plug by

pulling the power-cable.

• Make sure that the available mains supply voltage is

between 100~250V AC, 50/60Hz.

• Make sure that the power cable is never crimped or

damaged. Check the equipment and the power cable

periodically.

• If the equipment is dropped or damaged, disconnect the

mains power supply immediately and have a qualied

engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic

temperature uctuation (e.g. after transportation),

do not connect power or switch it on immediately.

The arising condensation might damage the equipment.

Leave the equipment switched off until it has reached

room temperature.

• If your product fails to function correctly, stop use

immediately. Pack the unit securely (preferably in the

original packing material), and return it to your Pro Light

dealer for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be

carried out by a qualied technician. THIS UNIT CONTAINS

NO USER SERVICEABLE PARTS.

• This lighting xture is for professional use only - it is

not designed for or suitable for household use. The

product must be installed by a qualied technician in

accordance with local territory regulations. The safety of

the installation is the responsibility of the installer. The

xture presents risks of severe injury or death due to re

hazards, electric shock and falls.

• Warning! Risk Group 2 LED product according to

EN 62471. Do not view the light output with optical

instruments or any device that may concentrate the beam.

• WARRANTY: One year from date of purchase.

www.prolight.co.uk Truss Booth LED Starcloth System, CW MKII

User Manual 3

Product overview & technical specications

Featuring 48 5mm white LEDs, this Truss Booth starcloth

comes supplied with an advanced DMX controller.

The controller features sound active, auto run and auto

fade modes. Supplied with heavy duty carry bag.

Truss Booth LED Starcloth System, CW MKII

Specications Controller

Power supply 100~250V, 50/60Hz

Fuse T1A 250V

Dimensions 55 x 205 x 145mm

ESC ENTER UP DOWN

WHITE STARCLOTH

CONTROLLER

www.prolight.co.uk

OUTPUT TO

STARCLOTHDMX INPUTDMX OUTPUTMICFUNCTION

OFF

POWER SUPPLY: 100-250V~50/60Hz

FUSE: T1A 250V

Software version

Static mode

u---

S000-S015

Ver

Stat

Slave mode

DMX Address selection

d.001-d.512

SLAv

Addr

LED string 4

Flash speed

LED string 2

LED string 1

LED string 3

A000-A255

b000-b255

C000-C255

d000-d255

CF00-CF99

PAtt

Auto mode Speed

Fade mode

Sound active mode

Pattern

mode

Auto Au00-Au08

so00-So08

FAde

Soud

AS00-AS99

Speed

FS00-F599

Sound sensitivity

SE00-SE31

205mm

145mm

ESC ENTER UP DOWN

WHITE STARCLOTH

CONTROLLER

www.prolight.co.uk

OUTPUT TO

STARCLOTHDMX INPUTDMX OUTPUTMICFUNCTION

OFF

POWER SUPPLY: 100-250V~50/60Hz

FUSE: T1A 250V

Software version

Static mode

u---

S000-S015

Ver

Stat

Slave mode

DMX Address selection

d.001-d.512

SLAv

Addr

LED string 4

Flash speed

LED string 2

LED string 1

LED string 3

A000-A255

b000-b255

C000-C255

d000-d255

CF00-CF99

PAtt

Auto mode Speed

Fade mode

Sound active mode

Pattern

mode

Auto Au00-Au08

so00-So08

FAde

Soud

AS00-AS99

Speed

FS00-F599

Sound sensitivity

SE00-SE31

ESC ENTER UP DOWN

WHITE STARCLOTH

CONTROLLER

www.prolight.co.uk

OUTPUT TO

STARCLOTHDMX INPUTDMX OUTPUTMICFUNCTION

OFF

POWER SUPPLY: 100-250V~50/60Hz

FUSE: T1A 250V

Software version

Static mode

u---

S000-S015

Ver

Stat

Slave mode

DMX Address selection

d.001-d.512

SLAv

Addr

LED string 4

Flash speed

LED string 2

LED string 1

LED string 3

A000-A255

b000-b255

C000-C255

d000-d255

CF00-CF99

PAtt

Auto mode Speed

Fade mode

Sound active mode

Pattern

mode

Auto Au00-Au08

so00-So08

FAde

Soud

AS00-AS99

Speed

FS00-F599

Sound sensitivity

SE00-SE31

145mm

55mm

Cloth:

• 48 x 5mm white LEDs

• Fast xx™ velcro tabs

• Low reection, re retardant material

• Includes an advanced DMX controller

• Carry bag included

Controller:

• DMX channels: 5

• Sound active, auto run and auto fade modes

• IEC power input

• 3-Pin XLR input/output

• 6-Pin XLR output to starcloth

www.prolight.co.uk Truss Booth LED Starcloth System, CW MKII

User Manual 4

Technical specications

ESC ENTER UP DOWN

WHITE STARCLOTH

CONTROLLER

www.prolight.co.uk

OUTPUT TO

STARCLOTHDMX INPUTDMX OUTPUTMICFUNCTION

OFF

POWER SUPPLY: 100-250V~50/60Hz

FUSE: T1A 250V

Software version

Static mode

u---

S000-S015

Ver

Stat

Slave mode

DMX Address selection

d.001-d.512

SLAv

Addr

LED string 4

Flash speed

LED string 2

LED string 1

LED string 3

A000-A255

b000-b255

C000-C255

d000-d255

CF00-CF99

PAtt

Auto mode Speed

Fade mode

Sound active mode

Pattern

mode

Auto Au00-Au08

so00-So08

FAde

Soud

AS00-AS99

Speed

FS00-F599

Sound sensitivity

SE00-SE31

01 - LED display

02 - Esc button

03 - Enter button

04 - Up button

05 - Down button

06 - Signal indicator

07 - Power indicator

08 - IEC power input

09 - Fuse T1A 250V

10 - Earth point

11 - On/off switch

12 - Function knob*

13 - Microphone

14 - 3-Pin DMX output

15 - 3-Pin DMX input

16 - 6-Pin XLR

output to starcloth

In the box:

1 x starcloth,

1 x power cable,

1 x controller &

1 x user manual

ESC ENTER UP DOWN

WHITE STARCLOTH

CONTROLLER

www.prolight.co.uk

OUTPUT TO

STARCLOTHDMX INPUTDMX OUTPUTMICFUNCTION

OFF

POWER SUPPLY: 100-250V~50/60Hz

FUSE: T1A 250V

Software version

Static mode

u---

S000-S015

Ver

Stat

Slave mode

DMX Address selection

d.001-d.512

SLAv

Addr

LED string 4

Flash speed

LED string 2

LED string 1

LED string 3

A000-A255

b000-b255

C000-C255

d000-d255

CF00-CF99

PAtt

Auto mode Speed

Fade mode

Sound active mode

Pattern

mode

Auto Au00-Au08

so00-So08

FAde

Soud

AS00-AS99

Speed

FS00-F599

Sound sensitivity

SE00-SE31

ESC ENTER UP DOWN

WHITE STARCLOTH

CONTROLLER

www.prolight.co.uk

OUTPUT TO

STARCLOTHDMX INPUTDMX OUTPUTMICFUNCTION

OFF

POWER SUPPLY: 100-250V~50/60Hz

FUSE: T1A 250V

Software version

Static mode

u---

S000-S015

Ver

Stat

Slave mode

DMX Address selection

d.001-d.512

SLAv

Addr

LED string 4

Flash speed

LED string 2

LED string 1

LED string 3

A000-A255

b000-b255

C000-C255

d000-d255

CF00-CF99

PAtt

Auto mode Speed

Fade mode

Sound active mode

Pattern

mode

Auto Au00-Au08

so00-So08

FAde

Soud

AS00-AS99

Speed

FS00-F599

Sound sensitivity

SE00-SE31

08 10 11 12 13 14 15 1609

0403

• * Rotate to scroll through menu. Press to enter or press and hold to exit.

Fitting instructions:

This cloth is designed to be tted to the inside of the Equinox Truss Booth.

Fit the cloth from the top of the booth rst by hanging the three sewn in top pockets onto the booth.

Carefully insert the crossbars through the square holes in either side of the cloth and secure on the

Truss Booth via the thumbscrews.

Once the crossbars have been tted, the cloth must be tensioned along the bottom and sides by the

integral velcro straps.

www.prolight.co.uk Truss Booth LED Starcloth System, CW MKII

User Manual 5

Operating instructions

Auto mode

To access the auto mode, press the “UP/DOWN” buttons on the front of the unit to show

“Auto”on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons

to set the auto mode you require. Press the “ENTER” button to conrm the setting. Now use the “UP” and

“DOWN” buttons to set the the speed required. Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “ESC” button.

Fade mode

To access the fade mode, press the “UP/DOWN” buttons on the front of the unit to show

“FAde”on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons

to set the the speed required. Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “ESC” button.

Sound active mode

To access the sound active mode, press the “UP/DOWN” buttons on the front of the unit to show

“Soud”on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons

to set the sound program you require. Press the “ENTER” button to conrm the setting. Now use the

“UP” and “DOWN” buttons to set the the sound sensitivity (00: lowest, 31: highest).

Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “ESC” button.

Pattern mode:

To access pattern mode, press the “UP/DOWN” buttons on the front of the unit to show

“PAtt”on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons

to set the brightness of LED string 1. Press the “ENTER” button to conrm the setting. Repeat this step for

LED string 2 - 4. Press the “ENTER” button to conrm the setting. Now use the “UP” and “DOWN” buttons

to set the the ash speed required. Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “ESC” button.

Slave mode:

To access the slave mode, press the “UP/DOWN” buttons on the front of the unit to show

“SLav”on the LED display. The unit is now in slave mode. Press the “ENTER” button to

conrm the setting.

To exit out of any of the above options, press the “ESC” button.

DMX address:

To change the DMX address, press the “UP/DOWN” buttons on the front of the unit to show

“Addr”on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons

to set the address you require. Press the “ENTER” button to conrm the setting. This is also the

mode that needs to be used when controlling the starcloth via DMX.

To exit out of any of the above options, press the “ESC” button.

www.prolight.co.uk Truss Booth LED Starcloth System, CW MKII

User Manual 6

Operating instructions

Software version:

To view the software version of the controller use the “UP/DOWN” buttons on the front of the unit to

show “VEr ”on the LED display. Now press the “ENTER” button and the version will be displayed in

the format “V---”.

To exit out of any of the above options, press the “ESC” button.

Static mode:

To access the static mode, press the “UP/DOWN” buttons on the front of the unit to show

“StAt”on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons

to set the static mode you require between “S000 - S015”.

Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “ESC” button.

Channel Value Function

1 0-20 LED group 1 blackout

21-230 LED group 1 ash speed

231-255 LED group 1 full on

2 0-20 LED group 2 blackout

21-230 LED group 2 ash speed

231-255 LED group 2 full on

3 0-20 LED group 3 blackout

21-230 LED group 3 ash speed

231-255 LED group 3 full on

4 0-20 LED group 4 blackout

21-230 LED group 4 ash speed

231-255 LED group 4 full on

5 0-100 All channels ash at speed set above

101-255 All channels full on

S000 Blackout

S001 LED group 1 on

S002 LED group 2 on

S003 LED group 3 on

S004 LED group 4 on

S005 LED group 1 & 2 on

S006 LED group 1 & 3 on

S007 LED group 1 & 4 on

5 channel mode:

S008 LED group 2 & 3 on

S009 LED group 2 & 4 on

S010 LED group 3 & 4 on

S011 LED group 1, 2 & 3 on

S012 LED group 1, 2 & 4 on

S013 LED group 1, 3 & 4 on

S014 LED group 2, 3 & 4 on

S015 All LEDs on

www.prolight.co.uk Truss Booth LED Starcloth System, CW MKII

User Manual 7

Setting the DMX address:

The DMX mode enables the use of a universal DMX controller. Each xture requires a “start address”

from 1- 511. A xture requiring one or more channels for control begins to read the data on the channel

indicated by the start address. For example, a xture that occupies or uses 7 channels of DMX and was

addressed to start on DMX channel 100, would read data from channels: 100,101,102,103,104,105

and 106. Choose a start address so that the channels used do not overlap. E.g. the next unit in the

chain starts at 107.

DMX 512:

DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent

xtures and controllers. A DMX controller sends DMX data instructions form the controller to the xture.

DMX data is sent as serial data that travels from xture to xture via the DATA “IN” and DATA “OUT”

XLR terminals located on all DMX xtures (most controllers only have a data “out” terminal).

DMX linking:

DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all xtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX xtures try to use the shortest

cable path possible. The order in which xtures are connected in a DMX line does not inuence the

DMX addressing. For example; a xture assigned to a DMX address of 1 may be placed anywhere in

a DMX line, at the beginning, at the end, or anywhere in the middle. When a xture is assigned a

DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit,

no matter where it is located in the DMX chain.

DATA cable (DMX cable) requirements (for DMX operation):

This xture can be controlled via DMX-512 protocol. The DMX address is set on the back of the unit.

Your unit and your DMX controller require a standard 3-pin XLR connector for data input/output,

see image below.

Note: DMX cable must be daisy chained and cannot be split.

DMX setup

Further DMX cables can be

purchased from all good sound

and lighting suppliers or

Pro Light Concepts dealers.

Please quote:

CABL10 – 2m

CABL11 – 5m

CABL12 – 10m

www.prolight.co.uk Truss Booth LED Starcloth System, CW MKII

User Manual 8

Notice:

Be sure to follow the diagrams below when making your own cables. Do not connect the cables

shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs

outer casing. Grounding the shield could cause a short circuit and erratic behaviour.

Special note:

Line termination:

When longer runs of cable are used,

you may need to use a terminator on

the last unit to avoid erratic behaviour.

Using a cable terminator will decrease

the possibilities of erratic behaviour.

(3-pin - Order code: CABL90, 5-pin - Order code: CABL89)

5-pin XLR DMX connectors:

Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-pin XLR xtures

may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a

3-pin line a cable adaptor must be used. The diagram below details the correct cable conversion.

Termination reduces signal transmission

problems and interference. It is always

advisable to connect a DMX terminal,

(resistance 120 Ohm 1/4 W) between pin 2

(DMX-) and pin 3 (DMX+) of the last xture.

5-pin XLR (female)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

3-pin XLR (female)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

3-pin XLR (male)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

5-pin XLR (male)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

DMX setup

www.prolight.co.uk Truss Booth LED Starcloth System, CW MKII

User Manual 9

Truss Booth Quad LED

Starcloth System

Order code: EQLED150N

Please contact your local retailer to purchase these accessories.

Optional accessories

Truss Booth Shelf Kit (Pair)

Order code: EQLED150H

www.prolight.co.uk Truss Booth LED Starcloth System, CW MKII

User Manual 10

Correct Disposal of this Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries

with separate collection systems)

This marking shown on the product or its literature, indicates that it should not be disposed of

with other household wastes at the end of its working life. To prevent possible harm to the

environment or human health from uncontrolled waste disposal, please separate this from other

types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their

local government ofce, for details of where and how they can take this item for environmentally

safe recycling.

Business users should contact their supplier and check the terms and conditions of the

purchase contract. This product should not be mixed with other commercial wastes for disposal.

WEEE notice

Inhaltsverzeichnis

Andere Equinox Systems DJ-Equipment Handbücher

Equinox Systems

Equinox Systems EQLED138 Bedienungsanleitung

Equinox Systems

Equinox Systems Spark Stream Bedienungsanleitung

Equinox Systems

Equinox Systems Scantastic 4 Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED12B Bedienungsanleitung

Equinox Systems

Equinox Systems MicroPar UV EQLED028 Bedienungsanleitung

Equinox Systems

Equinox Systems Ultra LED Scan EQLED75 Bedienungsanleitung

Equinox Systems

Equinox Systems Power Par 54 MKII Bedienungsanleitung

Equinox Systems

Equinox Systems Flame Machine 1.5M Bedienungsanleitung

Equinox Systems

Equinox Systems MIRR22 Bedienungsanleitung

Equinox Systems

Equinox Systems FXbar18 Bedienungsanleitung

Equinox Systems

Equinox Systems Helix 100W Gobo Flower Bedienungsanleitung

Equinox Systems

Equinox Systems Quad Pix Batten Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED019 Bedienungsanleitung

Equinox Systems

Equinox Systems Pulse Tube Lithium Bedienungsanleitung

Equinox Systems

Equinox Systems Domin8R II Bedienungsanleitung

Equinox Systems

Equinox Systems Fusion Orbit Bedienungsanleitung

Equinox Systems

Equinox Systems Blitzer Strobe Bedienungsanleitung

Equinox Systems

Equinox Systems Micro Batt EQLED160 Bedienungsanleitung

Equinox Systems

Equinox Systems Hot Rod EQLED089 Bedienungsanleitung

Equinox Systems

Equinox Systems Stratos Duo RGB Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED054 Bedienungsanleitung

Equinox Systems

Equinox Systems Beamtastic Bedienungsanleitung

Equinox Systems

Equinox Systems HYPE Bedienungsanleitung

Equinox Systems

Equinox Systems C-Shot Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung