Equinox Systems Microbor EQLED60 Bedienungsanleitung

Order code: EQLED60

USER MANUAL

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

Keep this equipment away from rain,

moisture and liquids.

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the

equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modications to this equipment are not

subject to warranty.

Equinox Microbar Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modication to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 220v/240v.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualied engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic temperature uctuation (e.g. after

transportation), do not switch it on immediately. The arising condensation might damage

the equipment. Leave the equipment switched off until it has reached room temperature.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualied

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

Equinox Microbar Technical specications

You should nd inside the carton the following items:

1, Equinox Microbar 2, Power cable 3, User manual

Technical Specications:

DMX channels: 6, 9 and 15 selectable

Operating modes: 1, Sound Activated

2, Built-in programmes

3, Auto Run

4, DMX

5, Slave

192 Ultra Bright 10mm LEDs (R: 36, G: 72, B: 84)

14 built-in programmes

4 Push button LCD digital display

Beam angle: 25˚

Mains IEC Power In/Out sockets

3-Pin XLR In/Out sockets for DMX

5-Pin socket for foot controller

Optional foot controller: MB-1 Foot Switch (EQLED61)

Power consumption: 35W

Power supply: 240V - 50Hz

Dimensions: 800 x 54 x 280mm

Weight: 5Kgs

Fuse: 0.5A

Overview

Identication:

1, Power output

2, Power input

3, On/Off switch

4, Remote input

5, DMX In

6, DMX out

O N

7, LCD digital display

8, Mode button

9, Setup button

10, Up button

11, Down button

Operation modes:

The Equinox Microbar has ve modes of operation as follows:

1, Sound active mode

To select the sound active mode, press the “MODE” button to show “SOUND MODE” in the LCD

display window. Now press the “SETUP” button and use the “UP” and “DOWN” buttons to

adjust the sound sensitivity level (SENS00-31) and press the “SET UP” button again to adjust the

frequency level (FQN01-99). Finally press the “SETUP” button to conrm your setting.

2, Built-in programmes mode

To access the built-in programme mode, press the “MODE” button to show “01.STATIC” in the

LCD display window. Now press the “SETUP” button and use the “UP” and “DOWN” buttons to

choose one of the 14 built-in programmes (01-14) (see table overleaf).

To choose one of the seven colours in the “STATIC” mode, press the set “SETUP” button and

use the “UP” and “DOWN” buttons to choose one of the following 7 colours:

(1) RGB = all on, (2) BR = purple, (3) B = blue, (4)GB = cyan,

(5) G = green, (6) RG = yellow, (7) R = red, BLA = blackout.

To adjust the speed level in the remaining 13 built-in programmes, press the SETUP” button and

use the “UP” and “DOWN” buttons to set the desired speed level (00-99).

To adjust the ash speed press the “SETUP” button and use the “UP” and “DOWN” buttons to

set the desired ash speed level (00-99). Finally press the “SETUP” button to conrm

your setting.

3, Auto Run mode

To select the Auto run mode, press the “MODE” button to show “AUTO RUN” in the LCD display

window. Now press the “SET UP” button to adjust the frequency level (FQN01-99). Finally press

the “SETUP” button to conrm your setting. The unit will now run all 13 built-in programmes one

after another.

4, DMX mode

To select the DMX mode, press the “MODE” button to show “DMX MODE” in the LCD display

window. Press the “SETUP” button and use the “UP” and “DOWN” buttons to set a DMX

address from 001-512. Now press the “SETUP” button again and use the “UP” and “DOWN”

buttons to choose one of the 3 DMX channel settings (6CH, 9CH or 15CH) Finally press the

“SETUP” button to conrm your setting. (see DMX chart). The starting address for this xture is

001.

5, Slave mode

To select Slave mode, rst link the units together via 3-Pin XLR cable(s), press the “MODE”

button to show “SLAVE MODE” on all of the slave units. Now the slave units will follow in

conjunction with the master unit.

NOTE: If the Micro Bar is being used in conjunction with the optional MB-1 foot controller

any number of Micro bars can be controlled via the foot controller by setting all Micro Bars

to 6 channel DMX mode.

NOTE: The frequency level (FQN01-99) adjusts how many times the programme repeats

before moving to the next programme.

Equinox Microbar Operation modes

Built-in programme chart

Equinox Microbar Operation modes

Static Colour

BLAC-RGB Flash00-99

Dream

Speed00-99 Flash00-99

Meteor

Speed00-99 Flash00-99

Fade

Speed00-99 Flash00-99

Change

Speed00-99 Flash00-99

Flow 1

Speed00-99 Flash00-99

Flow 2

Speed00-99 Flash00-99

Flow 3

Speed00-99 Flash00-99

Flow 4

Speed00-99 Flash00-99

Flow 5

Speed00-99 Flash00-99

Flow 6

Speed00-99 Flash00-99

Flow 7

Speed00-99 Flash00-99

Flow 8

Speed00-99 Flash00-99

1. BLAC-RGB 2. BLAC-RGB

Flow 9

Speed00-99 Flash00-99

1. BLAC-RGB 2. BLAC-RGB

Red-Yellow-Green-Cyan-Blue-Purple-White-Blackout

Flash speed adjustable

7 colour dreaming

Speed & Flash adjustable

7 colour ow

Speed & Flash adjustable

7 colour fade

Speed & Flash adjustable

7 colour change

Speed & Flash adjustable

7 colour chase in 1 direction

Speed & Flash adjustable

7 colour chase in 2 directions

Speed & Flash adjustable

7 colour relay chase in 1 direction

Speed & Flash adjustable

7 colour relay chase in 2 directions

Speed & Flash adjustable

7 colour chase from sides to centre

Speed & Flash adjustable

7 colour chase from centre to side

Speed & Flash adjustable

7 colour chase

Speed & Flash adjustable

2 colour chase in 1 direction

Speed & Flash adjustable

Red-Yellow-Green-Cyan-Blue-Purple-White-Blackout

2 colour chase in 2 directions

Speed & Flash adjustable

Red-Yellow-Green-Cyan-Blue-Purple-White-Blackout

6 channel DMX chart (All four LED pods adjusted at the same time)

9 channel mode (Adjusts the LED pods in pairs)

15 channel mode (Adjusts each LED pod individually)

Equinox Microbar DMX Charts

CH 4

Red

pods

3+4

CH 5

Green

pods

3+4

CH 6

Blue

pods

3+4

CH 7

Red

pods

1+2

CH 8

Green

pods

1+2

CH 9

Blue

pods

1+2

CH 4

Red

pod

CH 5

Green

pod

CH 6

Blue

pod

CH 7

Red

pod

CH 8

Green

pod

CH 9

Blue

pod

CH 10

Red

pod

CH 11

Green

pod

CH 12

Blue

pod

CH 13

Red

pod

CH 14

Green

pod

CH 15

Blue

pod

Further DMX cables can be purchased from all

good sound and lighting suppliers or Prolight

dealers.

Please quote:

CABL10 – 2M

CABL11 – 5M

CABL12 – 10M

DMX Control Mode

Operating in a DMX control mode environment gives the user the greatest exibility when it comes

to customising or creating a show. In this mode you will be able to control each individual trait of

the xture and each xture independently.

Setting the DMX address

The DMX mode enables the use of a universal DMX controller. Each xture requires a

“start address” from 1- 511. A xture requiring one or more channels for control begins to read the

data on the channel indicated by the start address. For example, a xture that occupies or uses 7

channels of DMX and was addressed to start on DMX channel 100, would read data from

channels: 100,101,102,103,104,105 and 106. Choose a start address so that the channels used

do not overlap. E.g. the next unit in the chain starts at 107.

DMX-512:

• DMX (Digital Multiplex) is a universal protocol used as a form of communication between

intelligent xtures and controllers. A DMX controller sends DMX data instructions form the

controller to the xture. DMX data is sent as serial data that travels from xture to xture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only have

a data “out” terminal).

DMX Linking:

• DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all xtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX xtures try to use the

shortest cable path possible. The order in which xtures are connected in a DMX line does not

inuence the DMX addressing. For example; a xture assigned to a DMX address of 1 may be

placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a

xture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to

address 1 to that unit, no matter where it is located in the DMX chain.

DATA Cable (DMX cable) requirements (for DMX operation):

• The Equinox Microbar can be controlled via DMX-512 protocol. The DMX address is set on the

back of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for

data input/output (gure 1).

Figure 1

Also remember that DMX cable must be daisy chained and cannot be split.

Equinox Microbar DMX set up

Notice:

• Be sure to follow gures 2 & 3 when making your own cables. Do not connect the cable’s shield

conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer

casing. Grounding the shield could cause a short circuit and erratic behaviour.

Special Note: Line termination:

• When longer runs of cable are used, you may need to use a terminator on the last unit to

avoid erratic behaviour.

Using a cable terminator (part number CABL90) will decrease the possibilities of erratic

behaviour.

5-Pin XLR DMX Connectors:

• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin

XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin

XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the

correct cable conversion.

Termination reduces signal transmission problems

and interferance. it is always advisable to connect a

DMX terminal, (resistance 120 Ohm 1/4 W) between

pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.

Equinox Microbar DMX Set Up

Notes:

Equinox Microbar Notes

Inhaltsverzeichnis

Andere Equinox Systems DJ-Equipment Handbücher

Equinox Systems

Equinox Systems EQLED136 Bedienungsanleitung

Equinox Systems

Equinox Systems Graphix Bedienungsanleitung

Equinox Systems

Equinox Systems Hot Rod EQLED089 Bedienungsanleitung

Equinox Systems

Equinox Systems Twin Shot MKII Electric Confetti Launcher Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED368 Bedienungsanleitung

Equinox Systems

Equinox Systems PRO DJ Booth LED Starcloth System Bedienungsanleitung

Equinox Systems

Equinox Systems Domin8R II Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED135 Bedienungsanleitung

Equinox Systems

Equinox Systems Truss Booth LED Starcloth System CW MKII Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED039A Bedienungsanleitung

Equinox Systems

Equinox Systems Waterwave XP Bedienungsanleitung

Equinox Systems

Equinox Systems Blitzer Strobe Bedienungsanleitung

Equinox Systems

Equinox Systems Beamtastic Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED019 Bedienungsanleitung

Equinox Systems

Equinox Systems Power Par 54 MKII Bedienungsanleitung

Equinox Systems

Equinox Systems C-Shot Bedienungsanleitung

Equinox Systems

Equinox Systems Crossfire XP Bedienungsanleitung

Equinox Systems

Equinox Systems FEVER Bedienungsanleitung

Equinox Systems

Equinox Systems Stratos Wash RGBA Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED162 Installations- und Betriebshandbuch

Equinox Systems

Equinox Systems 2M Flight CasedDMX LED Flame Machine Bedienungsanleitung

Equinox Systems

Equinox Systems Stratos Duo RGB Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED12N Bedienungsanleitung

Equinox Systems

Equinox Systems SpectraPix Batten EQLED055 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung