Equinox Systems CARINA Bedienungsanleitung
CARINA
order code: EQLA03
user manual
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOUR INITIAL START-UP!
CAUTION!
Keep this equipment away from rain,
moisture and liquids.
SAFETY INSTRUCTIONS
Every person involved with the installation, operation & maintenance of this
equipment should:
- Be competent
- Follow the instructions of this manual
CAUTION! TAKE CARE USING THIS EQUIPMENT!
HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!
Before your initial start-up, please make sure that there is no damage caused during
transportation. Should there be any, consult your dealer and do not use the
equipment.
To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
Please note that damages caused by user modications to this equipment are not
subject to warranty.
Equinox Carina Laser Safety
Equinox Carina Laser Safety
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused
by the non-observance of this manual or any unauthorised modication to the
equipment.
• Never let the power-cable come into contact with other cables. Handle the power-cable
and all mains voltage connections with particular caution!
• Never remove warning or informative labels from the equipment.
• Do not open the equipment and do not modify the equipment.
• Do not connect this equipment to a dimmer-pack.
• Do not switch the equipment on and off in short intervals, as this will reduce the
system’s life.
• Only use the equipment indoors.
• Do not expose to ammable sources, liquids or gases.
• Always disconnect the power from the mains when equipment is not in use or before
cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the
power-cable.
• Make sure that the available voltage is between 220v/240v.
• Make sure that the power-cable is never crimped or damaged. Check the equipment and
the power-cable periodically.
• If the equipment is dropped or damaged, disconnect the mains power supply immediately.
Have a qualied engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic temperature uctuation (e.g. after
transportation), do not switch it on immediately. The arising condensation might damage
the equipment. Leave the equipment switched off until it has reached room temperature.
• If your product fails to function correctly, discontinue use immediately. Pack the unit
securely (preferably in the original packing material), and return it to your Prolight dealer
for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be carried out by a qualied
technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.
• WARRANTY; One year from date of purchase.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual,
the product may suffer damage and the warranty becomes void.
Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,
lamp failure etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and property.
You should nd inside the Laser carton the following items:
1, Pegasus Laser 2, Power cable
3, DMX cable 4, Instruction manual
Technical Specications:
Voltage: 240V AC 50Hz
Laser diode: 50mW Green (532nm) DPSS laser
Operating modes: 1, Stand Alone Sound Activated
2, Stand Alone Auto programme
3, Master/Slave
4, DMX-512 8 channels
Features:
Over 50 laser patterns, with adjustable scan rate, position and size giving a total of over 200
effects.
Function Settings:
1, Stand Alone Sound Activated, set all dip switches to off. Then use the
sensitivity control to set the desired activation level.
2, Stand Alone Auto Programme change, set dip switch 10 to on and all others to off.
Turn the sensitivity control to full on, the unit will then scroll through it’s internal patterns.
3, Master/Slave mode. To set the unit as Master use the Sound or Auto mode as above.
For Slave mode operation, set dip switch 1 to on and all others to off
4, For DMX operation set dip switch 10 to off, then set the desired address using dip
switches 1 - 9
When used in DMX mode please note:
Set Channel 1 to DMX No: 0to 50 for sound active mode.
Set Channel 1 to DMX No: 51 to 101 then using Channel 2 you can scroll through the 58 patterns
as listed below.
Set Channel 1 to DMX No: 102 to 152 then using Channel 3 you can obtain the single shapes
listed. With the single shapes selected you can then use
- Channel 4 to zoom
- Channel 5 for rotation
- Channel 6 for X movement
- Channel 7 for Y movement
- Channel 8 for scan speed
Set Channel 1 to DMX No: 153 to 203, the laser will then go into Auto run mode
Set Channel 1 to DMX No: 204 to 255, the laser will then go into blackout mode.
Note: The maximum number of units that can be linked in Master/Slave mode is 32. The patterns
are not perfect (squares, circles, triangles etc) as the unit uses stepper motors and not Galvo’s but
are ideal for use with smoke machines and to make lines and tunnels etc.
When using long DMX runs or multiple heads. A DMX terminator plug should be used on the last
head in the chain.
Equinox Carina Laser Technical specications
0-50
51-101
102-152
153-203
204-255
0-03
04-07
08-11
12-15
16-19
20-23
24-27
28-31
32-35
36-39
40-43
44-47
48-51
52-55
56-59
60-63
64-67
68-71
72-75
76-79
80-83
84-87
88-91
92-95
96-99
100-103
104-107
108-111
112-115
116-119
DMX table:
Equinox Carina Laser DMX Tables
Channel DMX Number Function
Channel 1
Channel 2
(Pattern mode 1)
Sound Activated mode
Pattern mode 1
Pattern mode 2
Auto running
Blackout
Circle zoom in/out
Short line rotation
Circle rotates around “X” axis
Circle rotates around “Y” axis
Circle
Circle rotates around “Y” axis
Circle moves left and right
Half circle
Half circle rotates around X” axis
Half circle rotates around “Y” axis
Half circle moves right and left
“W” rotation around “X” axis
“W” rotation around “Y” axis
Wave rotation around “X” axis
Line ows like waves
Waves move left and right
Square zoom in
Square moves around “X” axis
Square moves around “Y” axis
Square zoom out and rotation
Triangle zoom in/out
Triangle zoom out and rotation
Moving triangle
Moving line
Moving pentangle
Pentangle moves right and left
Line moves up and down
Line rotation
Line rotates around “Y” axis
Vertical line moves right to left
120-123
124-127
128-131
132-135
136-139
140-143
144-147
148-151
152-155
156-159
160-163
164-167
168-171
172-175
176-179
180-183
184-187
188-191
192-195
196-199
200-203
204-207
208-211
212-215
216-219
220-223
224-227
228-255
0-50
51-101
102-152
153-203
204-255
0-255
DMX table Cont:
Equinox Carina Laser DMX Tables
Channel DMX Number Function
Channel 2
vertical line rotates around “X” axis
Rotating leaf
Leaf zoom in/out
Hexagon zoom in/out
Hexagon Rotation
Small circle moves left and right
Small circle moves around
Small circle moves around
Dot move around
Short line ows like wave
Cloud moves left and right
Cloud rotation around Y axis
Cloud zoom out around X axis
Moving “V” shape
“V” rotation around “X” axis
“V” rotation around “Y” axis
“V” zoom in/out
“V” rotation around “Z” axis
Single wave rotation
Short line ows around single wave
Short line ows around double wave
Double wave zoom in
Rotating “+” shape
Zooming “+” sign
Line rotation around centre
Short line ows around “8” shape
“8” rotation
Rectangle rotation
Single shape 1 (line)
Single shape 2 (circle)
Single shape 3 (square)
Single shape 4 (dot)
Single shape 5 (triangle)
Single shape zoom in/out
Channel 3
Channel 4
0-49
50-149
150-255
0-255
0-255
0-255
DMX table Cont:
Back view:
Identication:
1, Power input
2, Power switch
3, Dip switches
4, Cooling fan
5, Hanging bracket
6, DMX in
7, DMX out
8, Volume Control
9, Microphone
10, LED power indicator
Equinox Carina Laser DMX Tables
Channel DMX Number Function
Channel 6
Single shape stops rotation
Single shape rotate anti-clockwise
Single shape rotate clockwise
Single shape moves around X axis
Single shape moves around Y axis
Controls the speed of single shape scanning
Channel 7
Channel 8
Channel 5
10
DMX Control Mode
Operating in a DMX control mode environment gives the user the greatest exibility when it comes
to customising or creating a show. In this mode you will be able to control each individual trait of
the xture and each xture independently.
Setting the DMX address
The DMX mode enables the use of a universal DMX controller. Each xture requires a
“start address” from 1- 511. A xture requiring one or more channels for control begins to read the
data on the channel indicated by the start address. For example, a xture that occupies or uses 7
channels of DMX and was addressed to start on DMX channel 100, would read data from
channels: 100,101,102,103,104,105 and 106. Choose a start address so that the channels used
do not overlap. E.g. the next unit in the chain starts at 107.
Set the start address using the group of dip switches located usually on the back of the xture.
Each dipswitch has an associated value. Adding the value of each switch in the ON position will
provide the start address. Determining which switches to toggle ON given a specic start address
can be accomplished in the following manner. By subtracting the largest switch value possible
from the selected start address until zero is achieved.
on
on
EXAMPLE STARTING ADDRESS
Address 10
Pin NO: 4 = 8
Pin NO: 2 = 2
Total = 10
Address 24
Pin NO: 5 = 16
Pin NO: 4 = 8
Total = 24
DMX address using
simple maths
233 - (128 = 105,Turn on dip No: 8
105 - (64) = 41,Turn on dip No:7
41 - (32) = 9,Turn on dip No: 6
9 - (8) = 1,Turn on dip No: 4
1 - (1) = 0,Turn on dip No:1
You will most likely use the first available
number which maybe Number 1.This
number was selected for
example purposes
DIP SWITCH (DMX VALUE)
1
2
3
4
5
6
7
8
9
10
1
2
4
8
16
32
64
128
256
Equinox Carina Laser DMX control mode
DMX-512:
• DMX (Digital Multiplex) is a universal protocol used as a form of communication between
intelligent xtures and controllers. A DMX controller sends DMX data instructions form the
controller to the xture. DMX data is sent as serial data that travels from xture to xture via the
DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only have
a data “out” terminal).
DMX Linking:
• DMX is a language allowing all makes and models of different manufactures to be linked together
and operate from a single controller, as long as all xtures and the controller are DMX compliant.
To ensure proper DMX data transmission, when using several DMX xtures try to use the
shortest cable path possible. The order in which xtures are connected in a DMX line does not
inuence the DMX addressing. For example; a xture assigned to a DMX address of 1 may be
placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a
xture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to
address 1 to that unit, no matter where it is located in the DMX chain.
DATA Cable (DMX cable) requirements (for DMX operation):
• The Equinox laser can be controlled via DMX-512 protocol. The DMX address is set on the back
of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for data
input/output (gure 1).
Figure 1
Also remember that DMX cable must be daisy chained and cannot be split.
Equinox Carina Laser DMX set up
Further DMX cables can be purchased from all
good sound and lighting suppliers or Prolight
dealers.
Please quote:
CABL10 – 2M
CABL11 – 5M
CABL12 – 10M
Notice:
• Be sure to follow gures 2 & 3 when making your own cables. Do not connect the cable’s shield
conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer
casing. Grounding the shield could cause a short circuit and erratic behaviour.
Special Note: Line termination:
• When longer runs of cable are used, you may need to use a terminator on the last unit to
avoid erratic behaviour.
Using a cable terminator (part number CABL90) will decrease the possibilities of erratic
behaviour.
5-Pin XLR DMX Connectors:
• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin
XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin
XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the
correct cable conversion.
Termination reduces signal transmission problems
and interferance. it is always advisable to connect a
DMX terminal, (resistance 120 Ohm 1/4 W) between
pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.
Equinox Carina Laser DMX Set Up
Inhaltsverzeichnis
Andere Equinox Systems Beleuchtungsausrüstung Handbücher
Equinox Systems
Equinox Systems PEGASUS II Bedienungsanleitung
Equinox Systems
Equinox Systems Axis 50W Gobo Flower Bedienungsanleitung
Equinox Systems
Equinox Systems LED Par 64 Bedienungsanleitung
Equinox Systems
Equinox Systems Fusion 150 Bedienungsanleitung
Equinox Systems
Equinox Systems UV Mini Batten 9 Bedienungsanleitung
Equinox Systems
Equinox Systems Cirrus Bedienungsanleitung
Equinox Systems
Equinox Systems Nova Par 64 Bedienungsanleitung
Equinox Systems
Equinox Systems NEBULA Bedienungsanleitung
Equinox Systems
Equinox Systems CAPRICORN EQLA22 Bedienungsanleitung
Equinox Systems
Equinox Systems PREDATOR Bedienungsanleitung
Equinox Systems
Equinox Systems EQLED040 Bedienungsanleitung
Equinox Systems
Equinox Systems Tri Power Batten MKII Bedienungsanleitung
Equinox Systems
Equinox Systems EQLED203 Bedienungsanleitung
Equinox Systems
Equinox Systems Gigabar MKII COB Bedienungsanleitung
Equinox Systems
Equinox Systems POLARIS Bedienungsanleitung
Equinox Systems
Equinox Systems Spectra Strobe Batten Bedienungsanleitung
Equinox Systems
Equinox Systems ARIES EQLA20 Bedienungsanleitung
Equinox Systems
Equinox Systems ATRIA Bedienungsanleitung
Equinox Systems
Equinox Systems Fusion Saber Bedienungsanleitung
Equinox Systems
Equinox Systems TRINITY BEAM Bedienungsanleitung
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
