Equinox Systems Krypton EQLED21 Bedienungsanleitung
KRYPTON
order code: EQLED21
user manual
user manual
www.prolight.co.uk
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOUR INITIAL START-UP!
CAUTION!
Keep this equipment away from rain,
moisture and liquids.
SAFETY INSTRUCTIONS
Every person involved with the installation, operation & maintenance of this
equipment should:
- Be competent
- Follow the instructions of this manual
CAUTION! TAKE CARE USING THIS EQUIPMENT!
HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!
Before your initial start-up, please make sure that there is no damage caused during
transportation. Should there be any, consult your dealer and do not use the
equipment.
To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
Please note that damages caused by user modications to this equipment are not
subject to warranty.
Equinox Krypton Safety
Equinox Krypton Safety
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused
by the non-observance of this manual or any unauthorised modication to the
equipment.
• Never let the power-cable come into contact with other cables. Handle the power-cable
and all mains voltage connections with particular caution!
• Never remove warning or informative labels from the equipment.
• Do not open the equipment and do not modify the equipment.
• Do not connect this equipment to a dimmer-pack.
• Do not switch the equipment on and off in short intervals, as this will reduce the
system’s life.
• Only use the equipment indoors.
• Do not expose to ammable sources, liquids or gases.
• Always disconnect the power from the mains when equipment is not in use or before
cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the
power-cable.
• Make sure that the available voltage is between 220v/240v.
• Make sure that the power-cable is never crimped or damaged. Check the equipment and
the power-cable periodically.
• If the equipment is dropped or damaged, disconnect the mains power supply immediately.
Have a qualied engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic temperature uctuation (e.g. after
transportation), do not switch it on immediately. The arising condensation might damage
the equipment. Leave the equipment switched off until it has reached room temperature.
• If your product fails to function correctly, discontinue use immediately. Pack the unit
securely (preferably in the original packing material), and return it to your Prolight dealer
for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be carried out by a qualied
technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.
• WARRANTY; One year from date of purchase.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual,
the product may suffer damage and the warranty becomes void.
Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,
lamp failure etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and property.
You should nd inside the Equinox carton the following items:
1, Kryton Unit 2, Power cable 3, Instruction manual
Technical Specications:
Voltage: AC 230 ~ 50Hz
27 Ultra bright 10mm LED’s (R: 9, G: 9, B:9)
Dimensions: 370 x 175 x 155mm
Weight: 3.6Kg
Operating modes: 1, Stand Alone
2, Programme Selection
3, Sound Active
4, Master/Slave
5, DMX-512: 6 channels
Function Settings:
1, Stand Alone, set all dipswitches to off. Then use
dipswitches 5 - 8 to control the speed.(5=slow, 8=fast)
2, Programme Selection, set dipswitches 1,2,3 or 4 to on and all others to off. Then use
dipswitches 5 - 8 to control the speed.(5=slow, 8=fast)
3, Sound Activated 1, set dipswitch 9 to on and all others to off. (colour change)
4, Sound Activated 2, set dipswitch 1 + 9 to on and all others to off. (colour change with dimming)
5, Sound Activated 3, set dipswitch 2 + 9 to on and all others to off. (colour change and colour change with dimming)
6, Master/Slave mode. To set the unit as Master use the Sound or Auto mode as above.
For Slave mode operation, set dipswitch 10 to on and all others to off
7, For DMX operation set dipswitch 10 to on, then set the desired address using dip
switches 1 - 9
When used in DMX mode please follow the channel function chart on the next page:
Equinox Kryton Technical specications
Overview:
1, DMX input
2, DMX output
3, Power input
4, Power output
5, Dipswitches
6, Fuse (0.5A)
000-027
028-055
056-083
084-111
112-139
140-167
168-195
196-223
224-255
000-255
000-015
016-255
000-255
000-255
000-255
DMX table:
Equinox Kryton DMX Tables
Channel DMX Number Function
Channel 1
Channel 2
Dimming
3 colour change
7 colour change
Colour fade
Colour dream
Auto run
7 colour change via Sound active
7colour change dimmimg via
Sound active
7 colour change and 7 colour
dimming via Sound active
Speed
Off
Strobe
Red
Green
Blue
Channel 3
Channel 4
Channel 5
Channel 6
DMX Control Mode
Operating in a DMX control mode environment gives the user the greatest exibility when it comes
to customising or creating a show. In this mode you will be able to control each individual trait of
the xture and each xture independently.
Setting the DMX address
The DMX mode enables the use of a universal DMX controller. Each xture requires a
“start address” from 1- 511. A xture requiring one or more channels for control begins to read the
data on the channel indicated by the start address. For example, a xture that occupies or uses 7
channels of DMX and was addressed to start on DMX channel 100, would read data from
channels: 100,101,102,103,104,105 and 106. Choose a start address so that the channels used
do not overlap. E.g. the next unit in the chain starts at 107.
Set the start address using the group of dip switches located usually on the back of the xture.
Each dipswitch has an associated value. Adding the value of each switch in the ON position will
provide the start address. Determining which switches to toggle ON given a specic start address
can be accomplished in the following manner. By subtracting the largest switch value possible
from the selected start address until zero is achieved.
on
on
EXAMPLE STARTING ADDRESS
Address 10
Pin NO: 4 = 8
Pin NO: 2 = 2
Total = 10
Address 24
Pin NO: 5 = 16
Pin NO: 4 = 8
Total = 24
DMX address using
simple maths
233 - (128 = 105,Turn on dip No: 8
105 - (64) = 41,Turn on dip No:7
41 - (32) = 9,Turn on dip No: 6
9 - (8) = 1,Turn on dip No: 4
1 - (1) = 0,Turn on dip No:1
You will most likely use the first available
number which maybe Number 1.This
number was selected for
example purposes
DIP SWITCH (DMX VALUE)
1
2
3
4
5
6
7
8
9
10
1
2
4
8
16
32
64
128
256
Equinox Kryton DMX control mode
DMX-512:
• DMX (Digital Multiplex) is a universal protocol used as a form of communication between
intelligent xtures and controllers. A DMX controller sends DMX data instructions form the
controller to the xture. DMX data is sent as serial data that travels from xture to xture via the
DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only have
a data “out” terminal).
DMX Linking:
• DMX is a language allowing all makes and models of different manufactures to be linked together
and operate from a single controller, as long as all xtures and the controller are DMX compliant.
To ensure proper DMX data transmission, when using several DMX xtures try to use the
shortest cable path possible. The order in which xtures are connected in a DMX line does not
inuence the DMX addressing. For example; a xture assigned to a DMX address of 1 may be
placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a
xture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to
address 1 to that unit, no matter where it is located in the DMX chain.
DATA Cable (DMX cable) requirements (for DMX operation):
• The Equinox Kryton can be controlled via DMX-512 protocol. The DMX address is set on the
back of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for
data input/output (gure 1).
Figure 1
Also remember that DMX cable must be daisy chained and cannot be split.
Equinox Kryton DMX Set up
Further DMX cables can be purchased from all
good sound and lighting suppliers or Prolight
dealers.
Please quote:
CABL10 – 2M
CABL11 – 5M
CABL12 – 10M
Notice:
• Be sure to follow gures 2 & 3 when making your own cables. Do not connect the cable’s shield
conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer
casing. Grounding the shield could cause a short circuit and erratic behaviour.
Special Note: Line termination:
• When longer runs of cable are used, you may need to use a terminator on the last unit to
avoid erratic behaviour.
Using a cable terminator (part number CABL90) will decrease the possibilities of erratic
behaviour.
5-Pin XLR DMX Connectors:
• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin
XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin
XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the
correct cable conversion.
Termination reduces signal transmission problems
and interferance. it is always advisable to connect a
DMX terminal, (resistance 120 Ohm 1/4 W) between
pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.
Equinox Kryton DMX Set up
Equinox Kryton Dip Switch Reference Chart
DMX Dip Switch Quick Reference Chart
Dip Switch Position
Dip Switch position DMX Address
Inhaltsverzeichnis
Andere Equinox Systems Beleuchtungsausrüstung Handbücher
Equinox Systems
Equinox Systems EQLED008 Bedienungsanleitung
Equinox Systems
Equinox Systems Fusion Saber Bedienungsanleitung
Equinox Systems
Equinox Systems Terminator 2 Bedienungsanleitung
Equinox Systems
Equinox Systems Domin8r IIEQLED53 Bedienungsanleitung
Equinox Systems
Equinox Systems MaxiPar Tri Bedienungsanleitung
Equinox Systems
Equinox Systems 400W UV Cannon Bedienungsanleitung
Equinox Systems
Equinox Systems Kaleido EQLED85 Bedienungsanleitung
Equinox Systems
Equinox Systems SIGMA EQLA09 Bedienungsanleitung
Equinox Systems
Equinox Systems Spectra Strobe Batten Bedienungsanleitung
Equinox Systems
Equinox Systems LED Par 64 Bedienungsanleitung
Equinox Systems
Equinox Systems Fusion 150 Bedienungsanleitung
Equinox Systems
Equinox Systems SF-300 Bedienungsanleitung
Equinox Systems
Equinox Systems Swing Batten Bedienungsanleitung
Equinox Systems
Equinox Systems CAPRICORN EQLA22 Bedienungsanleitung
Equinox Systems
Equinox Systems CARINA Bedienungsanleitung
Equinox Systems
Equinox Systems EQLED65 Giga Bar System Bedienungsanleitung
Equinox Systems
Equinox Systems CONSTELLA Bedienungsanleitung
Equinox Systems
Equinox Systems PIXELpoint Batten Bedienungsanleitung
Equinox Systems
Equinox Systems EQLED013 Bedienungsanleitung
Equinox Systems
Equinox Systems FLAM11 Bedienungsanleitung
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
