Ergotron 48" Bench II Bedienungsanleitung

01– 48”Wide Bench Shelf...................... Qty. 1........................... (see below)

28” Deep (ABS4829zz-xx and ABS4835zz-xx)

36” Deep (ABD4829zz-xx and ABD4835zz-xx)

02– Bench Leg Assemblies ................... Qty. 2

25” Bench Legs (ABS4829zz-xx and ABD4829zz-xx)

31” Bench Legs (ABS4835zz-xx and ABD4835zz-xx)

03– Bench Arm Left................................. Qty. 1

04– Cross Ends .......................................... Qty. 2

05– 1” Button-hd PB Screw................... Qty. 12

06– M6x12mm insert screw ................. Qty. 4

07– 2.5” End Caps ..................................... Qty. 4

08– Caster Inserts..................................... Qty. 4

09– Caster, 5” locking.............................. Qty. 4

10– M8x101mm button head screw. Qty. 8

11– Curved Washers................................ Qty. 8

12– Bench Base Tubes ............................ Qty. 2

28” Deep (ABS4829zz-xx and ABS4835zz-xx)

36” Deep (ABD4829zz-xx and ABD4835zz-xx)

Enclosed Parts List

13– 15” Bench Buttress........................... Qty. 2

14– 41.5” Bench Cross Tubes................ Qty. 2

15– Keps Nuts M6 .................................... Qty. 8

16– M6x12mm Pan screws ................... Qty. 8

17– Bench Arm Right.............................. Qty. 1

18– Support Screws ................................ Qty. 20

19– 48” Bench Pans.................................. Qty. 2

All Screw quantities listed here are the minimum needed for your

Bench assembly. There may be a few extra Screws included, which

are not counted in the Parts List.

To make the assembly of your Bench even easier, we have included the

required tools.. The handy Hex Driver Bit can be used in your electric

drill in place of the Hex Driver.

20- Tool, Hex Driver M4 ........................... Qty. 1

21- Tool, Hex Driver Bit 5/32”.................... Qty. 1

22- Tool, Hex Key 1/4”................................. Qty. 1

Tool, 3-Way Wrench(not shown).......... Qty. 1

These Assembly Instructions

are for the 48”Bench models.

Before beginning assembly

of your Bench, please take a

moment to review the parts

listed below to verify that your

shipment is complete.

11 14

15 16

48” Bench II

Your Bench is heavy!

Don’t try to lift it yourself. Work

with a buddy.

RI

UHY(ವ

www.ergotron.com | USA: 1-800-888-8458 | Europe: +31 (0)33-45 45 600 | China: 400-120-3051 | Japan: [email protected]

)RUWKHODWHVW8VHU,QVWDOODWLRQ*XLGHSOHDVHYLVLWZZZHUJRWURQFRP

M6 x 12mm Insert Screw

(small pink patch on end)

Glide Inserts placed

into the large holes

Leave these two holes open

M8 x 101mm button head screw Curved Washer

Left Leg Assembly

Right Leg Assembly

Side holes

Cross Tubes

M8 x 101mm button head screw Curved Washer

Leave these two holes open

Lower holes

48” Bench

Assembly Instructions

Step 3

Position the Right Leg Assembly (from Step 2) with two

Cross Tubes as shown. Insert one Bench Cap Screw

with a Curved Washer through a side hole, carefully

threading the Screw into the Cross Tube.

Repeat entire procedure for the remaining three

side holes.

Step 2

Orient one Bench Leg Assembly with one Base Tube

Assembly (from Step 1). The Glide Inserts should be

facing down.

Insert one Screw through one Curved Washer, then

carefully insert through one of the lower holes on the

Base Tube, threading into the Right Leg Assembly.

Repeat this procedure for the remaining three lower

holes on the Right and Left Leg Assembly.

Install Bench Casters by threading one into each Caster

Insert.

Left Leg

Assembly

Right Leg

Assembly

Thread one Caster

into each Caster

Insert AFTER theBase

Tubes have been

installed to the Legs.

NOTE: Loosen these

Support Screws (if

needed) to allow the

Base Tube to install

easier.

Glide Inserts

Step 1

Use a mallet to install the two Bench Caster Inserts into

each Bench Base Tube and secure with one Insert Screw

per Insert.

Use a mallet to pop two End Caps into the ends of both

Base Tubes.

RI

UHY(ವ

Step 4

Determine the desired height of your Shelf. This instruction

will place the shelf at the top of the legs, either 34” or

40” from the oor (depending on which height Bench you

purchased).

The holes along the Leg Assemblies are spaced at 1”

increments. Adjusting either one hole up or down will

modify the nal Shelf height by 1” respectively. Rotating the

Glides will also provide additional height adjustment.

NOTE: Your Shelf height can be adjusted at a later time if needed

by following Steps 5-8 below.

Step 5

Position the Left Bench Arm onto the Left Leg Assembly.

Align the top two openings of the Arm with Hole 2 of the

Leg Assembly. Loosely install a Support Screw through

the top two holes of the Arm into the Leg.

Install the remaining six Support Screws into the Left

Arm, but do not fully tighten any of the Support Screws.

Repeat entire procedure for the Right Bench Arm on the

Right Leg Assembly.

Step 6 (requires a 3-Way Wrench)

Position a Bench Pan between the Arms, aligning the

two tabs on each Arm with the two holes in the lower

corners of a Pan. Insert a Pan Screw through the Pan

and Arm Tab- capturing it with a Keps Nut (but do not

fully tighten). Repeat this procedure for the remaining

end of the Pan and for the second Pan.

Tighten all Pan and Support Screws.

NOTE: the 3-Way Wrench can be used to assist in tighten-

ing the Keps Nuts.

M6 x 12mm Pan Screw

Support Screw

34” or 40”

Leave top two

Holes open Hole 2

Left Leg Assembly

Right Leg Assembly

M6 Keps Nut

Arms

Second Pan shown installed

REMINDER: You may want to measure

your equipment to make sure it ts into

the selected Shelf location.

Left Bench Arm

RI

UHY(ವ

Step 7

Place the Bench Shelf (laminate facing down) onto the oor.

With the help of another person, carefully rotate the Base

Assembly (from Step 6) over onto the Shelf.

Position the holes on the Pans and Arms to align with the twelve pre-

drilled holes on the Shelf. Insert two 1”Button-hd PB Screws through

each center opening of the Bench Pans (shown circled at right).

Install the remaining PB Screws into each of the Arms and Pans. A total

of twelve PB Screws will be installed.

If a drawer and/or keyboard caddy are a part of this conguration,

install them now using their instructions.

With the help of a buddy, carefully rotate your Bench right

side up.

Pans

Arms

Rounded Edge of Shelf

Predrilled holes

Lower Metal Mounts

Cable Grommet

Workstation Screw

(not counted in Parts List)

Removal of Leg Covers and Cable Grommets

Remove the Leg Cover by: 1. First removing the top two

Workstation Screws. 2. Slightly lift the Cover upward and

o the lower metal mounts.

Cable Grommets are snapped into and out of each of the

circular Leg openings.

Step 8 (requires a 3-Way Wrench)

FIRST- from the rear of your Bench, align one Buttress

with one hole on the Back Pan. Install a Pan Screw

through the Buttress and loosely capture using a Keps

Nut on the opposite side.

SECOND- position one Cross End on the remaining

Buttress end and install a Pan Screw and Keps Nut in the

same manner, but do not fully tighten.

THIRD- rotate the Buttress to align the Cross End with

two openings on the Leg. Secure the Cross End to the

Leg using two Support Screws.

Repeat this entire procedure for the remaining Buttress

and Cross End on the opposite end.

Tighten all Pan Screws, Support Screws and Keps Nuts.

Congratulations! Your 48” Bench assembly is complete.

M6 x 12mm Pan Screw

1” button Hd PB Screw

M6 Keps Nut

Buttress

Back Pan hole

Support Screw

FIRST Install this Pan Screw

SECOND Install this Pan Screw

THIRD Install the Cross End

NOTE: The purpose of the Buttress is not to

support your Bench Shelf. It is intended to make

your Bench absolutely rigid under extreme

weight conditions.

RI

UHY(ವ

RI

UHY(ವ

k(UJRWURQ,QF$OOULJKWVUHVHUYHG

www.ergotron.com |

USA: 1-800-888-8458

Europe: +31 (0)33-45 45 600

China: 400-120-3051

Japan: [email protected]

)RUORFDOFXVWRPHUFDUHSKRQHQXPEHUVYLVLWKWWSFRQWDFWHUJRWURQFRP

)RU6HUYLFHYLVLWZZZHUJRWURQFRP

)RU:DUUDQW\YLVLWZZZHUJRWURQFRPZDUUDQW\

Andere Ergotron Inneneinrichtung Handbücher

Ergotron

Ergotron LX Desk Mount LCD Arm Bedienungsanleitung

Ergotron

Ergotron TeachWell LCD Bedienungsanleitung

Ergotron

Ergotron WORKFIT Bedienungsanleitung

Ergotron

Ergotron Neo-Flex Bedienungsanleitung

Ergotron

Ergotron ZAH25CG/CG4 Bedienungsanleitung

Ergotron

Ergotron WORKFIT Standing Desk Converter Bedienungsanleitung

Ergotron

Ergotron WorkFit B Bedienungsanleitung

Ergotron

Ergotron Projector Shelf for TeachWell Bedienungsanleitung

Ergotron

Ergotron Zido 2-drawer Enclosure Bedienungsanleitung

Ergotron

Ergotron 72” AnthroBench II Bedienungsanleitung

Ergotron

Ergotron Neo-Flex Notebook PC Stand Bedienungsanleitung

Ergotron

Ergotron WorkFit-C Dual Bedienungsanleitung

Ergotron

Ergotron Styleview Vertical Lift LCD Monitor Abmessungen

Ergotron

Ergotron Elevate II Bedienungsanleitung

Ergotron

Ergotron WORKFIT-DL Bedienungsanleitung

Ergotron

Ergotron Zido ZAH25CG/CG4 Bedienungsanleitung

Ergotron

Ergotron 19610 Bedienungsanleitung

Ergotron

Ergotron WorkFit-D Bedienungsanleitung

Ergotron

Ergotron Zido ZGBCG Bedienungsanleitung

Ergotron

Ergotron LX Sit-Stand Bedienungsanleitung

Ergotron

Ergotron LearnFit SE Fehlerbehebungshandbuch

Ergotron

Ergotron LearnFit Bedienungsanleitung

Ergotron

Ergotron Yes 20 Bedienungsanleitung

Ergotron

Ergotron StyleView SV44 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung