Ergotron WorkFit-D Bedienungsanleitung

1 of 12

< 65 lbs. (29.5 kg)

888-24-205-G-01 rev. C • 09/12

WorkFit-D

2 of 12

888-24-205-G-01 rev. C • 09/12

These symbols alert users of a safety condition that

demands attention. All users should be able to

recognize and understand the signicance of the fol-

lowing Safety Hazards if encountered on the product

or within the documentation. Children who are not

able to recognize and respond appropriately to Safety

Alerts should not use this product without adult

supervision!

Hazard Symbols Review Symbol Signal Word Level of Hazard

NOTE A NOTE indicates important information that helps you

make better use of your Cart.

CAUTION

A CAUTION indicates either potential damage to

hardware or loss of data and tells you how to avoid the

problem.

WARNING AWARNING indicates either potential for property dam-

age, personal injury, or death.

ELECTRICAL

An Electrical indicates an impending electrical hazard

which, if not avoided, may result in personal injury, re

and/or death.

Safety

WARNING! TIPPING HAZARD!

When mounting accessories to the

WorkFit-D, they must stay within the foot

print. Do not mount accessories past the

front and rear worksurface! Failure to fol-

low this warning may result in equipment

damage and or personal injury.

826-463-00

WARNING

Moving Parts Can Crush And Cut

IMPACT HAZARD

1. Release hand brake and raise

worksurface to highest position.

2. Turn adjustment nuts at back of legs

counterclockwise until they stop (May

require 40-60 revolutions per leg).

To Minimize Lift Tension

Failure to heed this warning may

result in serious personal injury or

property damage!

For More information and instructions

visit www.ergotron.com or contact

Ergotron Customer Care at

1-800-888-8458.

- Removing Mounted Equipment

- Shipping Desk or Storing Desk

Minimize Lift Tension BEFORE:

✓

IMPORTANT! This product will need tension adjustments once installation is complete. Make sure all equipment

is properly installed on the product before attempting range of motion or tension adjustments. Any time

equipment is added or changed on this product resulting in a dierent mounted weight, you should repeat

the adjustment steps to ensure safe and optimum operation. This product should move smoothly and easily

through the full range of motion and stay where you set it. If movement is dicult or the product does not stay

where you set it, follow the adjustment instructions to loosen or tighten the tension to create a smooth, easy

motion. Depending on your product and the adjustment, it may take many turns to notice a dierence.

WARNING! After you complete your installation, never tip the desk to move or reposition

unless desk is raised to its highest position. Failure to follow these instructions may cause

lift engine to expand rapidly and may result in equipment damage and or personal injury.

3 of 12

888-24-205-G-01 rev. C • 09/12

WARNING! Stop screws are pre-installed in this product to secure it in the compressed

position during shipping and installation. DO NOT REMOVE THESE SCREWS UNTIL

INSTRUCTED TO DO SO IN THESE INSTRUCTIONS. Make sure these screws are in place

before starting installation. Failure to follow these instructions may cause lift engine to

expand rapidly and may result in equipment damage and or personal injury. If any of the 4

phillips head stop screws are not installed in these locations, contact customer care before

continuing with installation.

DO NOT REMOVE SCREWS!

IMPORTANT! Save these stop screws and instructions. Install stop screws when moving,

shipping or storing this product. Failure to follow these instructions may cause lift engine to

expand rapidly and may result in equipment damage and or personal injury.

777-24-038-G-00

WARNING

Keep Brake Cables Away from

Sync Rod and Crossbars

During Installation!

Failure to keep the brake cables away from

sync rod and crossbars may restrict lift

motion and may cause equipment damage

or personal injury! Refer to instruction

manual for more information.

4 of 12

# 12-14 Wood Screw

M5 x 6 mm

M2.9 x 8 mm

17x

3x 3x

16x

1/4”

14mm

888-24-205-G-01 rev. C • 09/12

Components

Tools Needed

5 of 12

Front =2 screws

Middle = 3 screws

Rear = 3 screws

Front Edge of Worksurface

Rear Edge of Worksurface

# 12-14 Wood Screw

Set the right leg (with hand brake) upright on the

worksurface.

Partially insert 3 of the provided #12-14 wood

screws at the rear of the leg, 3 near the middle of

the leg and 2 at the front of the leg.

888-24-205-G-01 rev. C • 09/12

Place the worksurface on a clean oor with

the top side facing down.

Carefully position the leg with the hand

brake on the right end of the worksurface.

Place the other leg on the left end.

Attach one end of the rod to the right

leg as illustrated.

Set-up Steps

NOTE: The brake cable is attached to both legs. Take care when removing the legs

from the packaging to avoid damaging or pulling the brake cable from the legs.

NOTE: Do not fully

insert the screws

into the worksurface

at this time. Leave

approximately 1/8”

space.

777-24-038-G-00

WARNING

Keep Brake Cables Away from

Sync Rod and Crossbars

During Installation!

Failure to keep the brake cables away from

sync rod and crossbars may restrict lift

motion and may cause equipment damage

or personal injury! Refer to instruction

manual for more information.

6 of 12

NOTE: Do not

fully insert

the screws

into the work-

surface at this

time. Leave

approximate-

ly 1/8” space.

# 12-14 Wood Screw

16x

M5 x 6 mm

888-24-205-G-01 rev. C • 09/12

Use a Phillips screwdriver to insert the

provided M5x6 mm screws into the two

crossbars connecting the left and right legs.

Tighten the screws slightly one at a time

and repeat to ensure that the tension on

every screw is equal.

Partially insert 9 of the provided #12-14 wood screws

in the left leg and worksurface.

Set the left leg (without

hand brake) upright on

the worksurface.

Attach the left end of

the rod to the left leg.

Use a Phillips screwdriver to tighten

down the screws attaching the legs to

the worksurface.

Set-up Steps

Rear = 3 screws

Front =3 screws

Middle = 3 screws

NOTE: Do not overtighten screws.

overtightening screws may result in

stripping the holes and may cause the

installation to be unsafe.

NOTE: Do not overtighten screws. overtightening

screws may result in stripping the holes and may

cause the installation to be unsafe.

777-24-038-G-00

WARNING

Keep Brake Cables Away from

Sync Rod and Crossbars

During Installation!

Failure to keep the brake cables away from

sync rod and crossbars may restrict lift

motion and may cause equipment damage

or personal injury! Refer to instruction

manual for more information.

777-24-038-G-00

WARNING

Keep Brake Cables Away from

Sync Rod and Crossbars

During Installation!

Failure to keep the brake cables away from

sync rod and crossbars may restrict lift

motion and may cause equipment damage

or personal injury! Refer to instruction

manual for more information.

7 of 12

3x 3x

M2.9 x 8 mm

888-24-205-G-01 rev. C • 09/12

Capture the brake cable in the cable clip as

illustrated, then use a Phillips screwdriver to attach

the cable clips to bottom of work surface with the

provided M2.9 x 8 mm screws.

Using the 2 provided cable ties, attach brake cable

to the legs leaving as much slack in cable as possible

between the cable tie and the leg to allow desk top to

raise up unrestricted.

Set-up Steps

NOTE: Leave as much slack

in cable as possible between

the cable tie and the leg to

allow desk top to raise up

unrestricted. Failure to follow

this may result in equipment

damage.

777-24-038-G-00

WARNING

Keep Brake Cables Away from

Sync Rod and Crossbars

During Installation!

Failure to keep the brake cables away from

sync rod and crossbars may restrict lift

motion and may cause equipment damage

or personal injury! Refer to instruction

manual for more information.

8 of 12

888-24-205-G-01 rev. C • 09/12

10 Set the desk upright onto its legs.

CAUTION!

LIFT HAZARD! Two persons

are required for this step.

Failure to follow this

warning may result in

equipment damage and or

personal injury.

Set-up Steps

11 Adjust the riser on each leg and check with a level to

make sure the work surface is even.

Spin Right to Lower.

Spin Left to Raise.

9 of 12

888-24-205-G-01 rev. C • 09/12

Set-up Steps

Install all equipment before removing the 4

brake stop screws.

CAUTION! Make sure you leave 20” (508mm) of slack

in all cables to allow the worksurface to raise up it’s

full 20” (508mm). Failure to allow enough slack in

cables may cause cables to get pulled, equipment to

fall o desk and may result in product damage and or

personal injury.

After installing all equipment, remove

the 2 stop screws from the legs then the

2 stop screws from the brake to allow the

worksurface to raise and lower.

IMPORTANT! Save these stop screws and

instructions. Install stop screws when moving,

shipping or storing this product. Failure to

follow these instructions may cause lift engine

to expand rapidly and may result in equipment

damage and or personal injury.

10 of 12

888-24-205-G-01 rev. C • 09/12

Adjustment Step

826-463-00

WARNING

Moving Parts Can Crush And Cut

IMPACT HAZARD

1. Release hand brake and raise

worksurface to highest position.

2. Turn adjustment nuts at back of legs

counterclockwise until they stop (May

require 40-60 revolutions per leg).

To Minimize Lift Tension

Failure to heed this warning may

result in serious personal injury or

property damage!

For More information and instructions

visit www.ergotron.com or contact

Ergotron Customer Care at

1-800-888-8458.

- Removing Mounted Equipment

- Shipping Desk or Storing Desk

Minimize Lift Tension BEFORE:

IMPORTANT! This product will need tension

adjustments once installation is complete. Make

sure all equipment is properly installed on the

product before attempting range of motion or

tension adjustments. Any time equipment is

added or changed on this product resulting in a

dierent mounted weight, you should repeat the

adjustment steps to ensure safe and optimum

operation. This product should move smoothly

and easily through the full range of motion and

stay where you set it. If movement is dicult or

the product does not stay where you set it, follow

the adjustment instructions to loosen or tighten

the tension to create a smooth, easy motion.

Depending on your product and the adjustment, it

may take many turns to notice a dierence.

Inhaltsverzeichnis

Andere Ergotron Inneneinrichtung Handbücher

Ergotron

Ergotron LX Desk Mount LCD Arm Bedienungsanleitung

Ergotron

Ergotron LearnFit 24-481-003 Bedienungsanleitung

Ergotron

Ergotron 97-540-053 Bedienungsanleitung

Ergotron

Ergotron StyleView SV44 Bedienungsanleitung

Ergotron

Ergotron WorkFit-A, Single LCD Mount, LD Bedienungsanleitung

Ergotron

Ergotron JUV Bedienungsanleitung

Ergotron

Ergotron WORKFIT Standing Desk Converter Bedienungsanleitung

Ergotron

Ergotron Zido 2-drawer Enclosure Bedienungsanleitung

Ergotron

Ergotron WorkFit-TLE Bedienungsanleitung

Ergotron

Ergotron LearnFit SE Fehlerbehebungshandbuch

Ergotron

Ergotron Neo-Flex Notebook Lift Stand Bedienungsanleitung

Ergotron

Ergotron Zido ZGBCG Bedienungsanleitung

Ergotron

Ergotron Bench II Bedienungsanleitung

Ergotron

Ergotron Modesty Panel Bedienungsanleitung

Ergotron

Ergotron LearnFit Bedienungsanleitung

Ergotron

Ergotron ZAH25CG/CG4 Bedienungsanleitung

Ergotron

Ergotron StyleView Bedienungsanleitung

Ergotron

Ergotron 19610 Bedienungsanleitung

Ergotron

Ergotron Neo-Flex Notebook PC Stand Bedienungsanleitung

Ergotron

Ergotron WorkFit-A, Single LCD Mount, LD Bedienungsanleitung

Ergotron

Ergotron SV10 Bedienungsanleitung

Ergotron

Ergotron WORKFIT-DL Bedienungsanleitung

Ergotron

Ergotron Carl's Table CT15 Bedienungsanleitung

Ergotron

Ergotron Yes 20 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung