Ergotron WorkFit B Bedienungsanleitung

1 of 19

888-24-227-G-01 rev. E • 12/19

www.ergotron.com | USA: 1-800-888-8458 | Europe: +31 (0)33-45 45 600 | China: 400-120-3051 | Japan: [email protected]

English, Español, Français, Deutsch, Nederlands, Italiano, Svenska, 日本語, 汉语

WorkFit

B, HD

™

User's Guide

English

For the latest User Installation Guide please visit: www.ergotron.com

2 of 19

888-24-227-G-01 rev. E • 12/19

826-901-00

WARNING

Moving Parts Can Crush And Cut

IMPACT HAZARD

Failure to heed this warning may result in

serious personal injury or property damage!

For More information and instructions visit www.ergotron.com

or contact Ergotron Customer Care at 1-800-888-8458.

Minimize Lift Strength BEFORE:

- Removing Mounted Equipment

and

Insert 4 Stop Screws BEFORE:

- Shipping or Storing (i.e. when Desk is not upright).

To Minimize Lift Strength

Refer to installation manual for instructions on

how to minimize lift strength.

To Insert 4 Stop Screws

Refer to installation manual for instructions on

installing stop screws.

Refer to Appendix Aat the end of this manual

Refer to Appendix Bat the end of this manual

These symbolsalert users of asafety condition that

demands attention. All users shouldbeableto

recognize and understand the signi cance of the fol-

lowing Safety Hazards if encountered on the product

or within the documentation. Children who are not

ableto recognize and respond appropriately to Safety

Alerts shouldnot use this product without adult

supervision!

Hazard SymbolsReview SymbolSignal Word Level of Hazard

NOTE A NOTE indicates important information that helps you

make better use of this product.

CAUTION

A CAUTION indicates either potential damage to

hardware or loss of data and tellsyou how to avoid the

problem.

WARNING A WARNING indicates either potential for property dam-

age, personal injury, or death.

ELECTRICAL AnElectrical indicates an impending electrical hazard

which, if not avoided, may resultin personal injury, re

and/or death.

Safety

3 of 19

888-24-227-G-01 rev. E • 12/19

Safety

DO NOT REMOVESCREWS!

WARNING! Stop screws are pre-installed in this product to secure it in the compressed position

during shipping and installation. DO NOT REMOVE THESE SCREWS UNTIL INSTRUCTED TO DO SO

IN THESE INSTRUCTIONS. Make sure these screws are in place before starting installation. Failure

to follow these instructions may cause lift engine to expand rapidly and may result in equipment

damage and or personal injury. If any of the 4 stop screws are not installed in these locations,

contact customer care before continuing with installation.

IMPORTANT!

Save these stop screws and instructions. Install stop screws

when shipping or storing this product. Failure to follow

these instructions may cause lift engine to expand rapidly

and may result in equipment damage and or personal

injury.

4 of 19

888-24-227-G-01 rev. E • 12/19

WARNING! TIPPING HAZARD!

When mounting accessories to the

WorkFit-D, they must stay within the foot

print. Do not mount accessories past the

front and rear worksurface! Failure to fol-

low this warning may resultin equipment

damage and or personal injury.

WARNING

Keep Brake Cables Awayfrom

Sync Rod and Crossbars

During Installation!

Failure to keep the brake cables away from

sync rod and crossbars may restrict lift

motion and may cause equipment damage

or personal injury! Refer to instruction

manual for more information.

Safety

Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly

installed on the product before attempting adjustments. This product should move smoothly and easily through

the full range of motion and stay where you set it. If movements are too easy or dicult or if product does not stay

in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your

product and the adjustment, it may take many turns to notice a dierence. Any time equipment is added or removed

from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps

to ensure safe and optimum operation.

5 of 19

888-24-227-G-01 rev. E • 12/19

0.80”-1.75”*

(20-44 mm)

23.5”-30.5”*

(597-775 mm)

41"-72" *

(1041-1829 mm)

22.5-88 lbs(10.2-40 kg)*

Features & Speciﬁ cations

Important! You will need to adjust this product after installation is

complete. Make sure all your equipment is properly installed on the

product before attempting adjustments. This product should move

smoothly and easily through the full range of motion and stay where

you set it. If movements are too easy or dicult or if product does

not stay in desired positions, follow the adjustment instructions to

create smooth and easy movements. Depending on your product

and the adjustment, it may take many turns to notice a dierence.

Any time equipment is added or removed from this product,

resulting in a change in the weight of the mounted load, you

should repeat these adjustment steps to ensure safe and optimum

operation.

*Total weight of worksurface and mounted equipment must

be< 88 lbs(40 kg).

Worksurface must meet ALL dimensional and weight range

specication requirements.

WARNING! The addition of accessories can negatively impact the

tip performance.

Wood Worksurface Weight Estimator

Worksurface

Thickness

Estimated Weight

per square foot

0.80” (20 mm) 2.9 lbs(1.32 kg)

1.25” (32 mm)4.5 lbs(2.04kg)

1.75” (44 mm) 6.3 lbs(2.86 kg)

6 of 19

888-24-227-G-01 rev. E • 12/19

AB C

1/4”

14mm

#12, Ø 0.19” (4.8mm)

#46, Ø 0.081” (2mm)

2.1262.126

12.992

5.118

3.900

35.197

DIMENSIONS ARE IN INCHES

WORKSURFACE TEMPLATE FOR WORKFIT-B,HD

Laythis template on the bottom of your worksurface

to drill the holes to attach theWorkFit-D,Base.

Back of Base Bracket

Brake Release

Use Drill Bit #21,

Ø 0.19” (4.8 mm)

to drill these 9 holes

0.375” (9.5 mm) deep.

Use Drill Bit #21,

Ø 0.19” (4.8 mm)

to drill these 8 holes

0.375” (9.5 mm) deep.

Use Drill Bit #46,

Ø 0.081” (2mm)

to drill these 3 holes

0.24” (6 mm) deep.

Center Point of Base Brackets

Depth of

Worksurface

TIPPING HAZARD!

Center Worksurface from Side-to-Side Across Base Brackets.

Failure to follow these instructions maymake this product unstable

and mayresult in equipment damage and/or personal injury.

823-558-00 rev.A 05/13

23.50 - 24.25”----0.25”

24.25 - 25.00”----0.75”

25.00 - 25.75”----1.25”

25.75 - 26.50”----1.75”

26.50 - 27.25”----2.25”

27.25 - 28.00”----2.75”

28.00 - 28.75”----3.25”

28.75 - 29.50”----3.75”

29.50 - 30.25”----4.25”

Depth of

Worksurface

597 - 616 mm ---6 mm

616 - 635 mm ---19 mm

635 - 654 mm ---32 mm

654 - 673 mm ---44 mm

673 - 692 mm ---57 mm

692 - 711 mm ---70 mm

711 - 730 mm ---83 mm

730 - 749 mm ---95 mm

749 - 768 mm ---108 mm

4.25”(108 mm)

3.75”(95 mm)

3.25”(83 mm)

2.75”(70 mm)

2.25”(57 mm)

1.75”(44 mm)

1.25”(32 mm)

0.75”(19 mm)

0.25”(6 mm)

Align

REAR

Edge of Worksurface

distance

from the back of the Base Brackets.

See table for value of

based on the depth of

your worksurface.

4.25”(108 mm)

3.75”(95 mm)

3.25”(83 mm)

2.75”(70 mm)

2.25”(57 mm)

1.75”(44 mm)

1.25”(32 mm)

0.75”(19 mm)

0.25”(6 mm)

M2.9 x 8mm ST3.9 x 16mm

M5 x 6mm

17x

16x

3x 4x

#12-14 x 5/8”

Components

ToolsNeeded

7 of 19

888-24-227-G-01 rev. E • 12/19

Brake Release

Use Drill Bit #21,

Ø 0.19” (4.8 mm)

to drill these 9 holes

3/8” (9.5 mm) deep.

Use Drill Bit #21,

Ø 0.19” (4.8 mm)

to drill these 8 holes

3/8” (9.5 mm) deep.

Use Drill Bit #46,

Ø 0.081” (2mm)

to drill these 3 holes

0.24” (6 mm) deep.

Center Point of Base Brackets

TIPPING HAZARD!

Center Worksurface from Side-to-Side Across Base Brackets.

Failure to follow these instructions maymake this product unstable

and mayresult in equipment damage and/or personal injury.

Brake Release

Use Drill Bit #21,

Ø 0.19” (4.8 mm)

to drill these 9 holes

3/8” (9.5 mm) deep.

Use Drill Bit #21,

Ø 0.19” (4.8 mm)

to drill these 8 holes

3/8” (9.5 mm) deep.

Use Drill Bit #46,

Ø 0.081” (2mm)

to drill these 3 holes

0.24” (6 mm) deep.

Center Point of Base Brackets

TIPPING HAZARD!

Center Worksurface from Side-to-Side Across Base Brackets.

Failure to follow these instructions maymake this product unstable

and mayresult in equipment damage and/or personal injury.

Brake Release

Use Drill Bit #21,

Ø 0.19” (4.8 mm)

to drill these 9 holes

3/8” (9.5 mm) deep.

Use Drill Bit #21,

Ø 0.19” (4.8 mm)

to drill these 8 holes

3/8” (9.5 mm) deep.

Use Drill Bit #46,

Ø 0.081” (2mm)

to drill these 3 holes

0.24” (6 mm) deep.

Center Point of Base Brackets

TIPPING HAZARD!

Center Worksurface from Side-to-Side Across Base Brackets.

Failure to follow these instructions maymake this product unstable

and mayresult in equipment damage and/or personal injury.

Depth of

Worksurface

23.50 - 24.25”----0.25”

24.25 - 25.00”----0.75”

25.00 - 25.75”----1.25”

25.75 - 26.50”----1.75”

26.50 - 27.25”----2.25”

27.25 - 28.00”----2.75”

28.00 - 28.75”----3.25”

28.75 - 29.50”----3.75”

29.50 - 30.25”----4.25”

Depth of

Worksurface

597 - 616 mm ---6 mm

616 - 635 mm ---19 mm

635 - 654 mm ---32 mm

654 - 673 mm ---44 mm

673 - 692 mm ---57 mm

692 - 711 mm ---70 mm

711 - 730 mm ---83 mm

730 - 749 mm ---95 mm

749 - 768 mm ---108 mm

2.1262.126

Back of Base Bracket

4.25” (108 mm)

3.75” (95 mm)

3.25” (83 mm)

2.75” (70 mm)

2.25” (57 mm)

1.75” (44 mm)

1.25” (32 mm)

0.75” (19 mm)

0.25” (6 mm)

Align

REAR

Edge of Worksurface

distance

from the back of the Base Brackets.

See table for value of

based on the depth of

your worksurface.

Place the worksurface on aclean oor with the top side facing down.

Center Template

Side-to-Side on

worksurface.

Align REAR Edge of Worksurface Xdistance from the back of the Base Brackets.

See tablefor value of Xbased on the depth of your worksurface.

Depth of

Your Worksurface

Tape Template in place.

Set-up Steps

8 of 19

888-24-227-G-01 rev. E • 12/19

#12, Ø 0.19” (4.8mm)

#46, Ø 0.081” (2mm)

Brake Release

Use Drill Bit #21,

Ø 0.19” (4.8 mm)

to drill these 9 holes

3/8” (9.5 mm) deep.

Use Drill Bit #21,

Ø 0.19” (4.8 mm)

to drill these 8 holes

3/8” (9.5 mm) deep.

Use Drill Bit #46,

Ø 0.081” (2mm)

to drill these 3 holes

0.24” (6 mm) deep.

Center Point of Base Brackets

TIPPING HAZARD!

Center Worksurface from Side-to-Side Across Base Brackets.

Failure to follow these instructions maymake this product unstable

and mayresult in equipment damage and/or personal injury.

Brake Release

Use Drill Bit #21,

Ø 0.19” (4.8 mm)

to drill these 9 holes

3/8” (9.5 mm) deep.

Use Drill Bit #21,

Ø 0.19” (4.8 mm)

to drill these 8 holes

3/8” (9.5 mm) deep.

Use Drill Bit #46,

Ø 0.081” (2mm)

to drill these 3 holes

0.24” (6 mm) deep.

Center Point of Base Brackets

TIPPING HAZARD!

Center Worksurface from Side-to-Side Across Base Brackets.

Failure to follow these instructions maymake this product unstable

and mayresult in equipment damage and/or personal injury.

DIMENSIONS ARE IN INCHES

WORKSURFACETEMPLATE FOR WORKFIT-D,BASEONLY

0.375"

(9.5 mm)

0.24"

(6 mm)

Using the specied drill bit, drill the 17 holes for base.

Using the specied drill bit, drill the 3 holes for cableclips.

Remove Template.

Set-up Steps

Drill holes 0.375" (9.5 mm) deep.

TIP: To ensure proper depth, place a

piece of tape on the drill bit 0.375”(9.5

mm) from the tip.

Drill holes 0.24" (6 mm) deep.

TIP: To ensure proper depth, place a piece of tape on the drill bit

0.24" (6 mm) from the tip.

9 of 19

888-24-227-G-01 rev. E • 12/19

8x #12-14 x 5/8”

Place the worksurface on aclean oor with

the top side facing down.

Carefully position the leg with the hand

brake on the right end of the worksurface.

Place the other leg on the left end.

Attach one end of the sync rod to the

right leg as illustrated. Make sure the

brake cables don’tloop around the sync

rod. See Warning, right.

Set-up Steps

NOTE: The brake cable is attached to both legs.Take care when re-

moving the legs from the packaging to avoid damaging or pulling the

brake cable from the legs.

NOTE: Do not fully

insert the screws

into the worksurface

at this time. Leave

approximately 1/8”

space.

Front =2 screws

Middle = 3 screws

Rear = 3 screws

Front Edge of Worksurface

Rear Edge of Worksurface

Set the right leg (with hand brake) upright on the

worksurface.

Partially insert 3 of the provided #12-14wood

screws at the rear of the leg, 3 near the middleof

the leg and 2 at the front of the leg.

WARNING

Keep Brake Cables Awayfrom

Sync Rod and Crossbars

During Installation!

Failure to keep the brake cables away from

sync rod and crossbars may restrict lift

motion and may cause equipment damage

or personal injury! Refer to instruction

manual for more information.

10 of 19

888-24-227-G-01 rev. E • 12/19

M5 x 6mm

16x

#12-14 x 5/8”

WARNING

Keep Brake Cables Awayfrom

Sync Rod and Crossbars

During Installation!

Failure to keep the brake cables away from

sync rod and crossbars may restrict lift

motion and may cause equipment damage

or personal injury! Refer to instruction

manual for more information.

Use aPhillips screwdriver to insert the provided M5x6

mm screws into the two crossbars connecting the left

and right legs. Make sure the brake cables don’t

loop around the crossbars.

Tighten the screws slightly one at atime

and repeat to ensure that the tension

on every screw is equal.

Partially insert 9 of the provided #12-14wood screws

in the left leg and worksurface.

Set the left leg (without

hand brake) upright on the

worksurface.

Attach the left end of the

sync rod to the left leg.

Make sure the brake cables

don’tloop around the sync

rod. See Warning, right.

Use aPhillips screwdriver to tighten

down the screws attaching the legs to

the worksurface.

NOTE: Do not overtighten screws.

overtightening screws may result in stripping

the holes and may cause the installation to be

unsafe.

NOTE: Do not overtighten screws. overtightening

screws may result in stripping the holes and may

cause the installation to be unsafe.

NOTE: Do not

fully insert

the screws

into the work-

surface at this

time. Leave

approximate-

ly 1/8” space.

Set-up Steps

Front =2 screws

Middle = 3 screws

Rear = 3 screws

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ergotron Inneneinrichtung Handbücher

Ergotron

Ergotron Styleview Vertical Lift LCD Monitor Abmessungen

Ergotron

Ergotron WorkFit-A, Single LCD Mount, LD Bedienungsanleitung

Ergotron

Ergotron Neo-Flex Notebook Lift Stand Bedienungsanleitung

Ergotron

Ergotron Modesty Panel Bedienungsanleitung

Ergotron

Ergotron Zido Handle Bedienungsanleitung

Ergotron

Ergotron 97-540-053 Bedienungsanleitung

Ergotron

Ergotron WORKFIT Bedienungsanleitung

Ergotron

Ergotron 48" Bench II Bedienungsanleitung

Ergotron

Ergotron Glide Upgrade Bedienungsanleitung

Ergotron

Ergotron WorkFit-A, Single LCD Mount, LD Bedienungsanleitung

Ergotron

Ergotron StyleView Bedienungsanleitung

Ergotron

Ergotron Zido 2-drawer Enclosure Bedienungsanleitung

Ergotron

Ergotron LearnFit 24-481-003 Bedienungsanleitung

Ergotron

Ergotron LearnFit SE Fehlerbehebungshandbuch

Ergotron

Ergotron LearnFit 24-756-003 Bedienungsanleitung

Ergotron

Ergotron Elevate II Bedienungsanleitung

Ergotron

Ergotron WORKFIT-DL Bedienungsanleitung

Ergotron

Ergotron Carl's Table CT15 Bedienungsanleitung

Ergotron

Ergotron WorkFit-C Dual Bedienungsanleitung

Ergotron

Ergotron WorkFit-T Bedienungsanleitung

Ergotron

Ergotron Zido ZGBCG Bedienungsanleitung

Ergotron

Ergotron LX Sit-Stand Bedienungsanleitung

Ergotron

Ergotron Neo-Flex Bedienungsanleitung

Ergotron

Ergotron Projector Shelf for TeachWell Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung