Erreka KAIROS Bedienungsanleitung
1
KAIROS
Elementos de la instalación completa
170
180
120 130 140 150 160
AB170 180110
160
150
140
130
120
110
110°~120°
100°~110°
90°~100°
>120°
AD
C
B
Quick Installation Guide MSB-029/02
WARNING
This quick guide is a summary of the complete installation manual. The manual contains safety warnings and
other explanations which must be taken into account. The installation manual can be downloaded by going
to the "Downloads" section of Erreka website:
http://www.erreka-automation.com
Elements of the complete installation
Electrical Wiring
A.B: 24v DC Motor(2x1mm²)
C: Photocell 2x0.5mm² (max 20m)
D: Control Box (3x1.5mm²)
E: Push Botton 2x0.5mm²(max 25m)
G
TATA
E F
A
B
Assembly levels, inward opening
KAIROS It is not applicable to an insecure or lacking rigidity door nor solves the defects due to incorrect installation or
Check the following points before starting the installation:
1). Hinges are properly positioned and greased.
2). No obstacles in the moving area and no frictions between two gate leafs or with the ground while moving.
3). “C” value is 139mm.
4). “D” can be measured from the gate easily.
5). “A” = “C” + “D”
6). The value of “B” can be calculated from the value of “A” and the leaves opening angle.
Ex. If “A”=160mm with the leaves opening angle of 100 degrees, then the value of “B” is approximate 190mm.
Please make sure B and A are similar or the same in value that the leaves can be
operated smoothly, also to reduce the burden of the motor.
Open Interior
F: Key Selector(2x0.5 mm²)
G: Flash Light (2x0.5mm²)
H.I: Electric Lock (2x1mm²)
TA: Open Stopper
TC: Close Stopper
D
C
TC H
I
0
2
Unlocking
Push the lid of release chamber
Turn counterclockwise the knob.
Insert the key and turn counterclockwise
to the unlock position
Unlocking for manual operation:
Motorised operation locking:
Then turn clockwise the knob to
release the motor.
12 3
Insert the key and turn clockwise. Close the lid of release chamber.
1 2 3
Please make sure B and A are similar or the same invaluethat the leaves can be operated smoothly,
also to reduce the burden of the motor.
Assembly levels, outward opening
Open Exterior
B
A
3
Assembly
e
Check the door manually which can be moved easily in
entire route.
Fix the front bracket. Check the motor is completely leveled.
and mounting position.
no.1
AD
C
B
1 2 3
4
7 8
5 6
Block the motor and make the electrical wiring. To connect the cables M1 and M2 correctly. If you only
install one gate, connect the wires to the terminal M1.
Horizontal 180O
no.2
A
B
B
A
Technical Features
4
Dimensions
917mm
877mm
124mm123mm
350 5mm
+
-
Max gate length
Max gate weight
Power supply
Motor power supply
Gear Type
Peak Thrust
Normal Thrust
Operation Stroke
Piston extention
Opening Time
Duty Cycle
Protection Grade (IP)
Operation temperature
Absorbed current (A)
Absorbed Power (W)
Manual Release
Dimensions
3m
300kg
110V/230VAC (50-60Hz) SMART-D201M / SMART-D201
24VDC
Worm and worm gear
3000N
2500N
350mm
25.5mm/sec
<14 sec
20%
IP44
-20oC~50oC
5,5 A for a 10 sec. max.
144W
key
917mm * 123mm * 124mm
5
(+)
(-)
A1 B2
(+)
(-)
M2-M1-
Lat-
Lit- Lmt4Lmt3
Lmt2
Lit+ SKey
S1
M2+
M1+Lat+ Ph2Ph1 PhVcc PhVcc
S25V
ANT
GND
DKey GND
GND GND GND
Lmt1 GND
J5
K5
K3
K2K1
J4 J3
J7
J8
NC NO
CO
+-
NC NO
CO
+-- +
CO
NONC
- +
CO
NONCNC NO
CO
+-
1 2 3 4 5 6 7 8
910 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
LED3
LED4
LED2
LED Azul-Memorización Radio
LED2 Pulsador o Selector de llave
LED3 Fotocélula 1
LED4 Fotocélula 2
Electrical connections SMART-D201 (M)
Electrical connections VIVO-D203 (M)
A1 Operator 1
A2 Operator 2
G1/G4 Red cable (motor)
G2/G5 Blue cable (motor)
SW1 Main switch
● Select the number of operators using C0 (C001: one operator, C002: two operators).
● Select the directions using C1 (A1) and C2 (A2).
● Programme C7 for operation without encoder or limit switches (C700).
● Adjust the trapping force in accordance with the weight of the gate (parameter A6).
Turning direction check: after connecting the power and activating any of the key devices, the
gate makes a reset (the display shows rS): the gate closes until it reaches the stopper, assigning this
stopper with the position "gate closed" If it opens instead of closes during the reset, change turning
direction using C1 (A1) or C2 (A2).
A1 Operator 1
A2 Operator 2
5/7 M1+ Operator 1/ M2+ Operator 2
6/8 M1- Operator 1/ M2- Operator 2
● Select the number of operators using F2 (F22: one operator, F21: two operators).
● Confirm gate opening direction of A1 and A2 during system programing (first operation is close),
if does not correspond, change the cable connection M+ and M- of corresponding.
● Programme F1 for operation without encoder or limit switches (F11).
● Adjust the trapping force in accordance with the weight of the gate (parameter F3).
Maximum trapping force during system learning process: please make sure the parameter F3“
Maximum trapping force” is in F3-1 during the open/close programming.
A1
A2
VIVO-D203:
VIVO-D203M:
Inhaltsverzeichnis
Andere Erreka Toröffner Handbücher
Erreka
Erreka ARES Benutzerhandbuch
Erreka
Erreka BUL BL33 Betriebsanleitung
Erreka
Erreka MAGIC Benutzerhandbuch
Erreka
Erreka VIVO-M101 Betriebsanleitung
Erreka
Erreka LINCE Betriebsanleitung
Erreka
Erreka IZAR Benutzerhandbuch
Erreka
Erreka DINGO Betriebsanleitung
Erreka
Erreka CICLON Series Bedienungsanleitung
Erreka
Erreka CICLON Benutzerhandbuch
Erreka
Erreka VULCAN Benutzerhandbuch
Erreka
Erreka SIRIUS Betriebsanleitung
Erreka
Erreka PUMA-I Betriebsanleitung
Erreka
Erreka MAGIC Betriebsanleitung
Erreka
Erreka Puma Betriebsanleitung
Erreka
Erreka TOPO Benutzerhandbuch
Erreka
Erreka VIVO-D102 Betriebsanleitung
Erreka
Erreka DINGO Betriebsanleitung
Erreka
Erreka ARC Series Benutzerhandbuch
Erreka
Erreka Puma Benutzerhandbuch
Erreka
Erreka HERA Technisches Dokument
Beliebte Toröffner Handbücher anderer Marken
Motorline professional
Motorline professional FORT Bedienungsanleitung
Beninca
Beninca BOB5024 Bedienungsanleitung
AGA
AGA GATEMASTER 900 HD Bedienungsanleitung
Chamberlain
Chamberlain MotorLift HC280ML Bedienungsanleitung
SOMFY
SOMFY Dexxo RTS Pro Bedienungsanleitung
Cardin
Cardin BL Series Bedienungsanleitung
