Erreka VULCAN D Betriebsanleitung

VULCAN D

Quick installation and programming guide English

WARNING

This quick guide is a summary of the complete installation manual. The manual contains safety warnings and

other explanations which must be taken into account. The installation manual can be downloaded by going

to the "Downloads" section of Erreka website:

http://www.erreka.com/Automatismos/descargaDocumentos.aspx

E237A

Elements of the complete installation

Electrical wiring

A: Main power supply

B: LUMI Flashing light

C: Photocells (Rx/Tx)

D: Pushbutton / key switch

E: Operator

F: LUMI Built-in antenna

G: Electrolock

VERY IMPORTANT:

The TC closing stopper and the TA

opening stoppers must be installed

in all cases.

The electrolock is compulsory for non-locking

operators. For locking operators, the electrolock must

be used for gate leaf lengths of over 1.8m.

MSH-024/01

E237D

Unlocking

Unlocking for manual operation:

•Open the cover (1).

•Turn the unlocking key (2) 90º until

it is perpendicular to the operator

spindle.

Motorised operation locking:

•Turn the unlocking key (2) 90º until

it is parallel to the operator spindle.

•Close the cover (1).

Locked Unlocked

M237D

700mm

80mm

960mm

M237C

M237F

Assembly levels

Inward opening

M237H

Level B

Level A

Opening angle

130

155

80º

130

140

85º

120

140

90º

145

115

90º

125

95º

120

100º

120

105

110º

Level B

Level A

Opening angle

135

150

80º

125

150

85º

155

100

90º

130

90º

130

120

95º

135

100

100º

125

110º

Outward opening

M237I

Levelling

The operator must work

horizontally: to do this, the supports

must be positioned at the same height.

Check horizontality with a spirit level.

P237H

P237C

P237U

P237D

P237E

P237F

P237V

Assembly

Mount the gland and introduce the

cables

4 cables are required.

8 Complete the electrical

connections as shown in the

section below. Then position the

cover (T) and tighten the gland.

Adjust the opening and closing

pressure, as described on the

next page. Lift the cover (1),

adjust the screws (1) and (2),

and, finally, close the cover (1).

1 Mount the fork in the operator.

Use the supplied horizontal pin as

the axis.

Mount the supports. Carry out

the welding with the operator

withdrawn to a distance, in order

to prevent the spindle from being

damaged by splashing.

3 Mount the operator on the rear

support.

Use the supplied narrow-head pin

as the axis.

P237A

P237K

Mount the operator on the front

support, using the supplied screw

as the axis.

Before doing this, apply grease to

the spindle and the orifices.

5 Mount the cover and top.

Secure using the screws supplied.

6 Loosen the discharge screw (P).

If the operator has to be

dismounted, retighten the

screw in order to prevent the

oil from leaking out.

ST1

FT1

P1 P2 P3

ST2

FT2

P4 P5 P6

STOP

P7 P8 P11

P12

LOCK

FCA1

FCC1

P15 P14 P16

P22 P23

Cour esy

Ligh Lamp.

G7 G8 G9 G10

24Vac

G4 G5 G6 G1 G2 G3

FCA2 COM FCC2

SCA

POWER

MOTOR2 (G2-G1-COM) MOTOR1 (G2-G1-COM)

P237WA

VIVO- M201:

230Vac/ 50Hz

VIVO- M201M:

125Vac/ 60Hz

A2 A1

Electrical connections

VIVO-M201(M)

The VIVO-M101(M) or VIVO-M201(M) control

board can be used for the VULCAN D operator.

Since this is a stationary unit for permanent

connection, an external cut-off must be

installed.

When using a single operator, connect it to

cable connectors G1, G2 and G3 (operator A1).

P237I

Adjusting the opening and closing pressures

The opening and closing pressures must be adjusted in line with the size and weight of the gate.

ODo not tighten the regulation screws (2) and (3) to the maximum, as this will result in damage.

Clockwork turning increases the pressure for both

screws. Anti-clockwork turning reduces the pressure.

The adjustment screws can be accessed by opening the

cover (1).

Pressure during the retraction of the spindle, screw (2):

In inward opening facilities, it corresponds to the opening

operation. In outward opening facilities, it corresponds to

the closing operation.

Pressure during the extension of the spindle, screw (3):

In inward opening facilities, it corresponds to the closing

operation. In outward opening facilities, it corresponds to

the opening operation.

After adjusting the pressures, close the cover (1).

Andere Handbücher für VULCAN D

Andere Erreka Toröffner Handbücher

Erreka

Erreka LINCE Betriebsanleitung

Erreka

Erreka CICLON Series Betriebsanleitung

Erreka

Erreka SIRIUS Betriebsanleitung

Erreka

Erreka TOPO Benutzerhandbuch

Erreka

Erreka Puma Benutzerhandbuch

Erreka

Erreka VIVO-M101 Betriebsanleitung

Erreka

Erreka CAT Betriebsanleitung

Erreka

Erreka PUMA-I Betriebsanleitung

Erreka

Erreka PUMA-I Betriebsanleitung

Erreka

Erreka NAOS Betriebsanleitung

Erreka

Erreka CICLON Benutzerhandbuch

Erreka

Erreka CICLON Betriebsanleitung

Erreka

Erreka DINGO Bedienungsanleitung

Erreka

Erreka VIVO-M201 Betriebsanleitung

Erreka

Erreka ARES Series Benutzerhandbuch

Erreka

Erreka MAGIC Betriebsanleitung

Erreka

Erreka CA53 Betriebsanleitung

Erreka

Erreka AMO02 Bedienungsanleitung

Erreka

Erreka AXIL Series Bedienungsanleitung

Erreka

Erreka IZAR Benutzerhandbuch

Erreka

Erreka Puma Betriebsanleitung

Erreka

Erreka Fenix Benutzerhandbuch

Erreka

Erreka CALYPSO Series Bedienungsanleitung

Erreka

Erreka HERA Technisches Dokument

Beliebte Toröffner Handbücher anderer Marken

Elite

Elite CSW200UL Bedienungsanleitung

CAME

CAME FROG-PM4 Bedienungsanleitung

SOMFY

SOMFY FX230 Bedienungsanleitung

Aprimatic

Aprimatic ONDA 500 Bedienungsanleitung

Turnstiles

Turnstiles FSW 900 Bedienungsanleitung

Beninca

Beninca R1-2 WBV Bedienungsanleitung

Motorline professional

Motorline professional FORT Bedienungsanleitung

Beninca

Beninca BOB5024 Bedienungsanleitung

AGA

AGA GATEMASTER 900 HD Bedienungsanleitung

Chamberlain

Chamberlain MotorLift HC280ML Bedienungsanleitung

SOMFY

SOMFY Dexxo RTS Pro Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Westfalia

Westfalia 85 27 06 Bedienungsanleitung

CAME

CAME F500 Bedienungsanleitung

Extel

Extel VERA Bedienungsanleitung

Comunello Automation

Comunello Automation ABACUS 220 Bedienungsanleitung

CAME

CAME FA40230CB Bedienungsanleitung

Mighty Mule

Mighty Mule 200 E-Z GATE OPENER UL325 SERIES Bedienungsanleitung