Erreka VIVO-D102 Betriebsanleitung

VIVO-D102(M)

Quick installation and programming guide English

IMPORTANT

NOTE

This quick guide is a summary of the complete installation manual. The manual contains safety warnings

and other explanations which must be taken into account. The installation manual can be downloaded by

going to the "Downloads" section at the Erreka website:

http://www.erreka.com/Automatismos/descargaDocumentos.aspx

E114A

ELECTRICAL CABLING:

Element Nº threads x section Maximum length

A: Main power supply 3x1.5mm230m

B: Flashing light / Traffic light 2x0.5mm2/ 3x0.5mm220m

C: Photocells (Tx / Rx) 2x0.5mm2/ 4x0.5mm230m

D: Pushbutton/wall key 2x0.5mm250m

E: Operator (motor + encoder) Duct (2x1mm2 + interior screened duct

2x0.5mm2)

8m (maximum 25m with

cable 2x2.5mm2)

F: Operator release 2x0.5mm225m

G: Antenna Coaxial cable 50k(RG-58/U) 5m

Elements of the complete installation

D102: 230Vac/ 50Hz

D102M: 125Vac/ 60Hz

MOTOR

ENCODER

STOP

MOTOR

ENCODER

P14

P15

P13

GND

SNG1

V+

CHG

BAT: (2x12V/1,2 Ah)

BATTERY

IN/OUT

ADO01

General connections

STOP CABLE CONNECTOR:

connect to the release switch

(in the models with encoder

and release). In the models

without release, make an

electrical bridge.

G1 Blue (motor)

G2 Red (motor)

P14 (GND) Mesh (encoder mesh) (–)

P15 (SNG1) Green (encoder signal) (S)

P13 (V+) Brown (encoder power supply) (+)

M114C

D1 and D2:

CL (static) Door closed

CL (flashing) Door closing

OP (static) Door open

OP (flashing) Door opening

XX (countdown) Door on standby

StOP Operator unlocked

PA (static) Pause (operation not complete)

rS (static)

Door searching for close position

D3 and D4:

C5 Closing safety device activated

E1 Encoder motor shudown

F1 Thrust limit exceeded

bA Battery working

Ftço Photocells defective (pre-testing)

Display indications

Turning direction change and check (C1)

This operation is only necessary if the operator opens the gate instead of closing it when making a reset (rS).

Radio code programming, P1 (only with RSD receiver)

If a receiver other

than RSD is used, see

the corresponding

instructions.

Open/close programming (P3)

The lower closing stopper must be installed before programming the run (see the

operator manual).

OWait whilst the door carries

out the open/close.

If you want the door to stop

before reaching the upper

stopper, press the transmitter

button at the required point.

Complete programming chart

D1 D2 Parameter D3 D4

Pre-

determined

option

Options or values

C1Motor turning direction 01x

4Disabled

5Closing safety device (photocell or strip) 00xDevice not installed

10 Device without testing

11 Device with testing

P1Total opening radio code programming oç

2Disabled

3Door open/close programming oç

F1Functioning mode 01 Automatic

02xStep-by-step

2Standby in automatic mode 0...5. 0...9 15 59 = 59 sec; 2.5 = 2 min. 50 sec., etc

3Disabled

A0Flashing light 01xNo pre-warning

02 With pre-warning

1Garage light time 0...5. 0...9 03 59 = 59 sec; 2.5 = 2 min. 50 sec., etc

2Door speed 0 1...5 03 01: minimum speed;

05: maximum speed

3Slowdown speed 0 1...5 03 01: minimum speed;

05: maximum speed

4Slowdown distance 0 0...5 00 00: minimum distance;

05: maximum distance

5Disabled

6Maximum thrust

maximum thrust in opening 1...9 X 6X 1X: minimum thrust (in opening);

9X: maximum thrust (in opening)

maximum thrust in closing X 1...9 X6 X1: minimum thrust (in closing);

X9: maximum thrust (in closing)

7Closing photocell used during standby (in

automatic mode only)

01 Immediate close

02xRestart standby time

03 Has no effect

8Pushbutton operation during standby (in

automatic mode only)

01 Immediate close

02xRestart standby time

03 Has no effect

9Opening mode 01xOpening in accordance with the mode

selected in the main functions (F)

02 Collective opening (the control board

does not obey the key commands during

opening)

03 Step-by-step opening (the door halts if a

key device is activated during opening.

The door closes when operated again)

ç1Operations carried out XX Indicates the cycles completed,

multiplying the indicated figure by an

amount, for example:

68 indicates 6,800 cycles completed

6.8 indicates 68,000 cycles completed

Andere Handbücher für VIVO-D102

Dieses Handbuch passt für folgende Modelle

Andere Erreka Toröffner Handbücher

Erreka

Erreka DINGO Betriebsanleitung

Erreka

Erreka Fenix Benutzerhandbuch

Erreka

Erreka VULCAN Benutzerhandbuch

Erreka

Erreka AMO02 Bedienungsanleitung

Erreka

Erreka CICLON Series Betriebsanleitung

Erreka

Erreka PUMA-I Betriebsanleitung

Erreka

Erreka KAIROS MSB-027/01 Bedienungsanleitung

Erreka

Erreka V2 CICLON Bedienungsanleitung

Erreka

Erreka VIVO-M201M Betriebsanleitung

Erreka

Erreka MAGIC Betriebsanleitung

Erreka

Erreka SIRIUS Betriebsanleitung

Erreka

Erreka ARES Benutzerhandbuch

Erreka

Erreka ARC Series Benutzerhandbuch

Erreka

Erreka VULCAN D Betriebsanleitung

Erreka

Erreka CICLON Betriebsanleitung

Erreka

Erreka CALYPSO Series Bedienungsanleitung

Erreka

Erreka Dolfin Betriebsanleitung

Erreka

Erreka TORO KM1800 Betriebsanleitung

Erreka

Erreka DINGO Bedienungsanleitung

Erreka

Erreka ARES Series Benutzerhandbuch

Erreka

Erreka CAT Betriebsanleitung

Erreka

Erreka VULCAN S Bedienungsanleitung

Erreka

Erreka Puma Betriebsanleitung

Erreka

Erreka TOPO Benutzerhandbuch

Beliebte Toröffner Handbücher anderer Marken

CAME

CAME FROG-PM4 Bedienungsanleitung

SOMFY

SOMFY FX230 Bedienungsanleitung

Aprimatic

Aprimatic ONDA 500 Bedienungsanleitung

Turnstiles

Turnstiles FSW 900 Bedienungsanleitung

Beninca

Beninca R1-2 WBV Bedienungsanleitung

Motorline professional

Motorline professional FORT Bedienungsanleitung

Beninca

Beninca BOB5024 Bedienungsanleitung

AGA

AGA GATEMASTER 900 HD Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Westfalia

Westfalia 85 27 06 Bedienungsanleitung

CAME

CAME F500 Bedienungsanleitung

Extel

Extel VERA Bedienungsanleitung

Comunello Automation

Comunello Automation ABACUS 220 Bedienungsanleitung

CAME

CAME FA40230CB Bedienungsanleitung

Mighty Mule

Mighty Mule 200 E-Z GATE OPENER UL325 SERIES Bedienungsanleitung

Riello Elettronica

Riello Elettronica CARDIN ACE FAST Handbuch

Telcoma

Telcoma ARM Handbuch

Telcoma

Telcoma ACE Handbuch