ESAB A6 OPC Bedienungsanleitung

Instruction manual

0333 125 001 GB 20190219

A6 OPC Flux recovery unit

TABLE OF CONTENTS

0333 125 001 © ESAB AB 2019

1SAFETY ....................................................................................................... 3

2TECHNICAL DESCRIPTION ....................................................................... 5

3OPERATION ................................................................................................ 7

4MAINTENANCE........................................................................................... 8

DIMENSION DRAWING....................................................................................... 9

SPARE PARTS .................................................................................................... 10

Rights reserved to alter specifications without notice.

1 SAFETY

0333 125 001 -3- © ESAB AB 2019

1 SAFETY

WARNING!

Arc welding and cutting can be injurious to yourself and others. Take precautions

when welding and cutting. Ask for your employer's safety practices which should be

based on manufacturers' hazard data.

ELECTRIC SHOCK - Can kill

• Install and earth the unit in accordance with applicable standards

• Do not touch live electrical parts or electrodes with bare skin, wet gloves or

wet clothing

• Insulate yourself from earth and the workpiece

• Ensure your working stance is safe

FUMES AND GASES - Can be dangerous to health

• Keep your head out of the fumes

• Use ventilation, extraction at the arc, or both, to take fumes and gases away

from your breathing zone and the general area

ARC RAYS - Can injure eyes and burn skin

• Protect your eyes and body. Use the correct welding screen and filter lens and

wear protective clothing

• Protect bystanders with suitable screens or curtains

FIRE HAZARD

• Sparks (spatter) can cause fire. Make sure therefore that there are no

inflammable materials nearby

NOISE - Excessive noise can damage hearing

• Protect your ears. Use earmuffs or other hearing protection.

• Warn bystanders of the risk

MALFUNCTION - Call for expert assistance in the event of malfunction.

Read and understand the instruction manual before installing or operating.

PROTECT YOURSELF AND OTHERS!

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety

precautions must meet the requirements that apply to this type of equipment. The following

recommendations should be observed in addition to the standard regulations that apply to

the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the

equipment. Incorrect operation of the equipment may lead to hazardous situations which can

result in injury to the operator and damage to the equipment.

1 SAFETY

0333 125 001 -4- © ESAB AB 2019

1. Anyone who uses the equipment must be familiar with:

○ its operation

○ location of emergency stops

○ its function

○ relevant safety precautions

○ welding and cutting or other applicable operation of the equipment

2. The operator must ensure that:

○ no unauthorised person is stationed within the working area of the equipment

when it is started up

○ no-one is unprotected when the arc is struck or work is started with the

equipment

3. The workplace must:

○ be suitable for the purpose

○ be free from drafts

4. Personal safety equipment:

○ Always wear recommended personal safety equipment, such as safety glasses,

flame-proof clothing, safety gloves

○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which

could become trapped or cause burns

5. General precautions:

○ Make sure the return cable is connected securely

○ Work on high voltage equipment may only be carried out by a qualified

electrician

○ Appropriate fire extinguishing equipment must be clearly marked and close at

hand

○ Lubrication and maintenance must not be carried out on the equipment during

operation

2 TECHNICAL DESCRIPTION

0333 125 001 -5- © ESAB AB 2019

2 TECHNICAL DESCRIPTION

The OPC flux recovery unit is intended for use on stationary and transportable welding units,

where a small, compact flux recovery unit is needed,

Maximum permissible air pressure: 6 kp/cm2

Air consumption at various pressures:

kp/cm² 4 5 6

liter/min 175 225 250

Rubber parts in the flux recovery unit can withstand temperatures encountered when using

preheated flux at up to 220 °C and with workpiece temperatures not exceeding 350 °C.

NOTE!

A metal flux hopper must be used.

Suction capacity data can be found in chapter "MAINTENANCE" of this manual.

The OPC flux recovery unit consists of:

1. Ejector, powered by compressed

air.

The side of the ejector intended

for connection to the cyclone is

fitted with a flange.

Connections are provided on the

other side of the ejector for the

suction hose and compressed air

hose 1/4 ".

2. Suction hose, connects the

recovery unit to the suction nozzle.

3. Suction nozzle, available in four

versions:

○ for normal butt welds

○ for larger butt welds

○ for fillet welds, left

○ for fillet welds, right

4. Nozzle bracket, holds the flux

recovery nozzle in position above

the weld.

5. Flux hopper, optional accessories.

6. Cyclone, for separating the

recovered flux from the air and

returning it to the flux hopper.

Fitted above the flux hopper.

7. Securing strap

8. Filter bag

2 TECHNICAL DESCRIPTION

0333 125 001 -6- © ESAB AB 2019

The flux hopper consists of:

1. Flux strainer, separates slag from flux

2. Flux hopper (10 l)

3. Flux hose, 1"×500 mm

4. Inspection window, for checking flux level

5. Manual flux valve

6. Adjustable flux outlet nozzle, for fitting to the welding head

3 OPERATION

0333 125 001 -7- © ESAB AB 2019

3 OPERATION

1. Check that the equipment is properly installed and that all hoses are secured.

2. Check that the flux valve is closed.

3. Fill the flux hopper with flux.

4. Open the flux valve, allowing the flux to run down on to the weld joint through the

supply nozzle.

5. Start welding and the suction unit at the same time. Unused flux will be sucked up

through the suction nozzle and hose into the cyclone, where the flux will be separated

from the slag. The flux falls through the strainer into the flux hopper, while the

dust-laden air is cleaned by the filter bag before being discharged.

6. Dimension drawing can be found in chapter "DIMENSION DRAWING" of this manual.

4 MAINTENANCE

0333 125 001 -8- © ESAB AB 2019

4 MAINTENANCE

1. Check that the rubber lining of the cyclone is undamaged, and replace it if necessary.

2. Check that all gaskets and joints are sealing properly.

3. Replace the filter bag when indicated by suction effect falling off after about 3-5

working hours. Performance can be improved by shaking the filter bag clean between

replacements.

*1 Air pressure (bar)

*2 Welding speed (m/min)

*3 Flux area (mm)

*4 H=Height of lift in m

At a suction height of 0.8 m, welding speed is not affected by the type of flux used.

Air pressure (kp/cm2)Suction height (m) Max welding speed (m/h)

6 0.8 70

5 0.8 60

4 0.8 45

DIMENSION DRAWING

0333 125 001 -9- © ESAB AB 2019

DIMENSION DRAWING

Flux recovery unit

1. Hose length 1000 mm

2. Nozzle length 210 mm

Flux hopper

SPARE PARTS

0333 125 001 - 10 - © ESAB AB 2019

SPARE PARTS

Spare parts may be ordered through your nearest ESAB dealer, see esab.com. When

ordering, please state product type, serial number, denominations and ordering numbers

according to the spare parts list. This facilitates dispatch and ensures correct delivery.

Maintenance and repair work should be performed by an experienced person, and electrical

work only by a trained electrician. Use only recommended spare parts.

C = Component designation in the circuit diagram

Inhaltsverzeichnis

Andere ESAB Schweißzubehör Handbücher

ESAB

ESAB SDF-50 Bedienungsanleitung

ESAB

ESAB CIGWELD Arcmaster 649 Payday Bedienungsanleitung

ESAB

ESAB Warrior YardFeed 200 Bedienungsanleitung

ESAB

ESAB ET 17 Bedienungsanleitung

ESAB

ESAB PREST-O-LITE PZ-503 Bedienungsanleitung

ESAB

ESAB EFU 30 Bedienungsanleitung

ESAB

ESAB CIGWELD 454342 Bedienungsanleitung

ESAB

ESAB PSE-10 Bedienungsanleitung

ESAB

ESAB MXH 315 PP Bedienungsanleitung

ESAB

ESAB A6 VEC Bedienungsanleitung

ESAB

ESAB LHI 825 Bedienungsanleitung

ESAB

ESAB SAVAGE A40 Bedienungsanleitung

ESAB

ESAB Sentinel A60 Bedienungsanleitung

ESAB

ESAB Eye-Tech 9-13 Bedienungsanleitung

ESAB

ESAB Arc Master ICE A6 S Bedienungsanleitung

ESAB

ESAB A6 GMD Bedienungsanleitung

ESAB

ESAB MT-400EHD Bedienungsanleitung

ESAB

ESAB Versotrac EWT 1000 Bedienungsanleitung

ESAB

ESAB PEI Bedienungsanleitung

ESAB

ESAB TWECO SPRAY MASTER V250 Wartungs- und Serviceanleitung

ESAB

ESAB A6 Mastertrac Bedienungsanleitung

ESAB

ESAB Cigweld ProGuard Bedienungsanleitung

ESAB

ESAB Eye-Tech 10-12 Select Bedienungsanleitung

ESAB

ESAB WeldCloud Mobile Bedienungsanleitung

Beliebte Schweißzubehör Handbücher anderer Marken

Lincoln Electric

Lincoln Electric LT-7 Tractor Bedienungsanleitung

Weco

Weco Trolley R Bedienungsanleitung

Cornwell Tools

Cornwell Tools MMWC1 Bedienungsanleitung

Dohle

Dohle ExOn2A Bedienungsanleitung

Nederman

Nederman Fume Eliminator FE 840/2500/P150 Bedienungsanleitung

3M Speedglas 9100 Series Bedienungsanleitung

Miller Electric

Miller Electric OM-842 Bedienungsanleitung

Miller

Miller A-200 Series Bedienungsanleitung

Abicor Binzel

Abicor Binzel ABIMIG WT Series Bedienungsanleitung

optrel

optrel lifeflip autopilot Bedienungsanleitung

Miller

Miller MIGmatic M-25 Bedienungsanleitung

Tregaskiss

Tregaskiss TOUGH GUN TT3 Reamer Bedienungsanleitung

Abicor Binzel

Abicor Binzel xFUME PRO Bedienungsanleitung

Sealey

Sealey SR20.V2 Bedienungsanleitung

iWeld

iWeld NORED EYE Bedienungsanleitung

Sthor

Sthor 74483 Bedienungsanleitung

Leister

Leister TWINNY T7 Bedienungsanleitung

Miller

Miller I-22 CE Bedienungsanleitung