ESAB Eye-Tech 11 Mono Bedienungsanleitung

INSTRUCTIONS for

Eye-Tech 11 Mono

Welding Helmet

P/N 15F22

ARC RAYS can burn eyes and skin. Wear safety

glasses and set proper filter shade. See ANSI/AWS

Z49.1 for guide. Available from American Welding

Society, Miami, FL 33135.

The Eye-Tech 11 Mono welding helmet is delivered fully

assembled and ready for use. You only need to adjust

the headband. The shade cartridge automatically dark-

ens to a shade 11 with arc ignition. The normal shade

before an arc is struck is 4 DIN.

Safety Precautions

zPitted or scratched plates reduce vision and protec-

tion. Replace worn or damaged parts immediately.

zAlways keep the external and internal protective plates

in place. Failure to do so will allow welding spatter to

pit the front surface of the shade cartridge. This can

reduce the built-in UV and IR protection. (Also, the weld

spatter will void the warranty on the shade cartridge.)

zDo not attempt to open the shade cartridge.

zDo not use in cold weather (below 14° F).

zKeep solar cells clean. Clean with a damp not wet, cloth

dipped in soapy water. Dry with a soft, clean cloth.

zDo not drop, strike, or bend helmet.

zDo not use abrasive cleaning agents.

zFumes and gases can be hazardous to your health.

Keep your head out of the fumes. Ventilate area or use

breathing devices, if necessary.

zKeep helmet dry (especially the shade cartridge) and

do not place on hot surfaces.

Operation

zCheck to see if the front cover lens is inserted and front

lens frame is in place.

zAdjust the headband tension. The helmet is ready to use.

The cartridge will darken with arc ignition.

Troubleshooting

zUneven darkening

- Protective helmet is not on straight, causing the dis-

tance between your eyes and the shade cartridge to

vary. If necessary, decrease distance to shade car-

tridge.

zThe shade cartridge does not darken or it flickers

- Sensors are dirty; clean

- Front cover lens is dirty or damaged; clean or replace

- Welding current is too low

zSlow switching times

- Temperature is too low (should not be below 14° F)

- Lighting is insufficient

zPoor visibility

- Shade levels are set incorrectly

- Front or rear cover lens is dirty

- Room lighting is insufficient

zWelding helmet slips

- Headband is not properly adjusted (set too low)

If these faults cannot be corrected, do not use

helmet. Contact your distributor for assistance.

F15-495

October, 2002

Be sure this information reaches the operator.

You can get extra copies through your supplier.

Specifications

Viewing Area: 3.86 x 1.50 (98 x 38mm)

Light transmittance: Shade level - 11

Automatic shade level function

Ultra-violet protection 15

Infra-red protection 14

Shade level 4 in non-active state

Switch Time: From light to dark 0.4 milliseconds at room

temperature; from dark to light 0.2-0.3 sec-

onds

Operating Temp.: 14° F to 158° F (-10°C to +70°C)

Power Supply: Solar cells

Helmet Construction: High impact, synthetic material

Weight: 16.6 oz (470 grams)

Technical details are subject to change.

To replace rear cover

lens, place a small

screwdriver in groove

and pull out lens.

To adjust angle of

helmet, turn

Eccentric knob.

Loosen locking-nuts and

adjust distance from eyes.

Adjust both sides at the same

time. Make sure helmet

remains straight.

To remove front lens frame

grasp bottom and pull upward; to

replace, reverse process.

F15-495 10/02 Printed in U.S.A.

SPARE PARTS LIST

Item P/N

1 - Front Lens Frame ..................................... 15F05

2 - Front Cover Lens (10 pcs) ......................... 15F09

3 - Shade Cartridge ........................................ 15F23

4 - Rear Cover Lens ........................................ 15F10

5 - Head Band ................................................ 15F03

6 - Sweat Band .............................................. 15F04

7 - Helmet (without shade cartridge) ............... 15F01

8 - Helmet Complete ...................................... 15F22

ACCESSORIES

Magnifying Lens P/N

- Diopter +0 ........................................................ 15F11

- Diopter +1.5 ..................................................... 15F12

- Diopter +2.0 ..................................................... 15F13

- Diopter +2.5 ..................................................... 15F14

After removing frames, insert front

cover lens into frame.

Use only P/N 15F09 front cover

lens. Replace front lens frame.

To replace shade cartridge, push

shade cartridge outwards from

the upper inside rim. To put back,

reverse process.

To adjust headband, set

upper adjusting strap as

low as possible.

The sweatband for the

forehead is removable

and washable.

Push in knob (at back of

headband) and turn. It

will then click into

position.

Warranty

A two-year warranty from the date of manufacture is given against

defects arising from faulty workmanship or materials. No war-

ranty is given against defects arising from misuse, unauthorized

interference with parts or use of the appliance which was not

intended by the manufacturer.

Andere ESAB Schweißzubehör Handbücher

ESAB

ESAB MXH 315 PP Bedienungsanleitung

ESAB

ESAB CIGWELD Arcmaster 649 Payday Bedienungsanleitung

ESAB

ESAB Warrior YardFeed 200 Bedienungsanleitung

ESAB

ESAB PREST-O-LITE PZ-503 Bedienungsanleitung

ESAB

ESAB SDF-50 Bedienungsanleitung

ESAB

ESAB PEI Bedienungsanleitung

ESAB

ESAB SAVAGE A40 Bedienungsanleitung

ESAB

ESAB Sentinel A50 Bedienungsanleitung

ESAB

ESAB SAVAGE A40 Bedienungsanleitung

ESAB

ESAB Aristo U6 Bedienungsanleitung

ESAB

ESAB Origo Feed 304 P4 Leitfaden

ESAB

ESAB EFU 30 Bedienungsanleitung

ESAB

ESAB Aristo U6 Bedienungsanleitung

ESAB

ESAB ET 17 Bedienungsanleitung

ESAB

ESAB 1500 ahma Bedienungsanleitung

ESAB

ESAB WeldCloud Mobile Bedienungsanleitung

ESAB

ESAB Eye-Tech 10-12 Select Bedienungsanleitung

ESAB

ESAB LHI 825 Bedienungsanleitung

ESAB

ESAB Eye-Tech 10-12 Select Bedienungsanleitung

ESAB

ESAB Arc Master ICE A6 S Bedienungsanleitung

ESAB

ESAB Versotrac EWT 1000 Bedienungsanleitung

ESAB

ESAB SDF-250 Bedienungsanleitung

ESAB

ESAB A6 S Arc Master Bedienungsanleitung

ESAB

ESAB PSE-10 Bedienungsanleitung

Beliebte Schweißzubehör Handbücher anderer Marken

Lincoln Electric

Lincoln Electric LT-7 Tractor Bedienungsanleitung

Cornwell Tools

Cornwell Tools MMWC1 Bedienungsanleitung

Dohle

Dohle ExOn2A Bedienungsanleitung

Nederman

Nederman Fume Eliminator FE 840/2500/P150 Bedienungsanleitung

3M Speedglas 9100 Series Bedienungsanleitung

Miller Electric

Miller Electric OM-842 Bedienungsanleitung

Miller

Miller A-200 Series Bedienungsanleitung

Abicor Binzel

Abicor Binzel ABIMIG WT Series Bedienungsanleitung

Miller

Miller MIGmatic M-25 Bedienungsanleitung

Tregaskiss

Tregaskiss TOUGH GUN TT3 Reamer Bedienungsanleitung

Abicor Binzel

Abicor Binzel xFUME PRO Bedienungsanleitung

Sealey

Sealey SR20.V2 Bedienungsanleitung

iWeld

iWeld NORED EYE Bedienungsanleitung

Sthor

Sthor 74483 Bedienungsanleitung

Leister

Leister TWINNY T7 Bedienungsanleitung

Miller

Miller I-22 CE Bedienungsanleitung

LAHTI PRO

LAHTI PRO L1540400 Bedienungsanleitung

Lincoln Electric

Lincoln Electric K3091-1 Bedienungsanleitung