ESAB Eye-Tech 10-12 Select Bedienungsanleitung

INSTRUCTIONS for

Eye-Tech 10-12 Select

Welding Helmet

P/N 15F20

ARC RAYS can burn eyes and skin. Wear safety

glasses and set proper filter shade. See ANSI/AWS

Z 9.1 for guide. Available from American Welding

Society, Miami, FL 33135.

The Eye-Tech 10-12 Select welding helmet is deliv-

ered fully assembled and ready for use. You only need

to adjust the headband and set the shade level. The

shade cartridge automatically darkens with arc igni-

tion.

Safety Precautions

lPitted or scratched plates reduce vision and protec-

tion. Replace worn or damaged parts immediately.

lAlways keep the external and internal protective plates

in place. Failure to do so will allow welding spatter to

pit the front surface of the shade cartridge. This can

reduce the built-in V and IR protection. (Also, the

weld spatter will void the warranty on the shade car-

tridge.)

lDo not attempt to open the shade cartridge.

lDo not use in cold weather (below 14° F).

lKeep solar cells clean. Clean with a damp not wet,

cloth dipped in soapy water. Dry with a soft, clean

cloth.

lDo not drop, strike, or bend helmet.

lDo not use abrasive cleaning agents.

lFumes and gases can be hazardous to your health.

Keep your head out of the fumes. Ventilate area or

use breathing devices, if necessary.

Keep helmet dry (especially the shade cartridge) and

do not place on hot surfaces.

Operation

lSet the slideswitch until it clicks to the shade level recom-

mended for your arc welding process. If you have doubts,

start with slideswitch in the 11-12 position. If you find that

the arc zone is too dark, then set slideswitch to the 1 -11

position.

lCheck to see if the front cover lens is inserted and front

lens frame is in place.

Troubleshooting

lUneven darkening

- Protective helmet is not on straight, causing the dis-

tance between your eyes and the shade cartridge to

vary. If necessary, decrease distance to shade cartridge.

lThe shade cartridge does not darken or it flickers

- Sensors are dirty; clean

- Front cover lens is dirty or damaged; clean or replace

- Welding current is too low

- Slideswitch not set properly (is in non-active center

position).

lSlow switching times

- Temperature is too low (should not be below 14° F)

- Lighting is insufficient

lPoor visibility

- Shade levels are set incorrectly

- Front or rear cover lens is dirty

- Room lighting is insufficient

lWelding helmet slips

- Headband is not properly adjusted (set too low)

If these faults cannot be corrected, do not use

helmet. Contact your distributor for assistance.

F-15-432

December, 1997

Be sure this information reaches the operator.

You can get extra copies through your supplier.

Specifications

Viewing Area: 3.86 x 1.50 (98 x 38mm)

Light transmittance: Ranges of sha e levels 10-11 & 11-12

Automatic sha e level function with selec-

tion of switch

Ultra-violet protection 15

Infra-re protection 14

Sha e level 4 in non-active state

Switch Time: From light to ark 0.1 millisecon s at room

temperature; from ark to light 0.2-0.3 sec-

on s

Operating Temp.: 14° F to 158° F (-10°C to +70°C)

Power Supply: Solar cells

Helmet Construction: High impact, synthetic material

Weight: 16.6 oz (470 grams)

Technical details are subject to change.

To replace rear cover

lens, place a small

screwdriver in groove

and pull out lens.

To adjust angle of

helmet, turn

Eccentric knob.

Loosen locking-nuts and

adjust distance from eyes.

Adjust both sides at the same

time. Make sure helmet

remains straight.

To remove front lens frame

grasp bottom and pull upward; to

replace, reverse process.

F-15-432 12/97 Printed in U.S.A.

Part

Spare Parts List Number

1 - Front Lens Frame ..................................... 15F 5

2 - Front Cover Lens (1 pcs) ........................ 15F 9

3 - Shade Cartridge ....................................... 15F21

4 - Rear Cover Lens (2 pcs) ........................ 15F1

5 - Eccentric Knob ......................................... 15F 8

6 - Head Band ............................................... 15F 3

7 - Sweat Band .............................................. 14F 4

8 - Helmet (without shade cartridge) .............. 15F 1

9 - Helmet Complete...................................... 15F2

ACCESSORIES

Part

Magnifying Lens Number

- Diopter + ........................................................15F11

- Diopter +1.5 .................................................... 15F12

- Diopter +2. .................................................... 15F13

- Diopter +2.5 .................................................... 15F14

After removing frames, insert front

cover lens into frame.

Use only P/N 15F0 front cover

lens. Replace front lens frame.

To replace shade cartridge, push

shade cartridge outwards from

the upper inside rim. To put back,

reverse process.

To adjust headband, set

upper adjusting strap as

low as possible.

The sweatband for the

forehead is removable

and washable.

Push in knob at back of

headband) and turn. It

will then click into

position.

Warranty

A two-year warranty from the date of manufacture is given against

defects arising from faulty workmanship or materials. No war-

ranty is given against defects arising from misuse, unauthorized

interference with parts or use of the appliance which was not

intended by the manufacturer.

Andere Handbücher für Eye-Tech 10-12 Select

Andere ESAB Schweißzubehör Handbücher

ESAB

ESAB WeldCloud Mobile Bedienungsanleitung

ESAB

ESAB CIGWELD Arcmaster 649 Payday Bedienungsanleitung

ESAB

ESAB SCT-4200 Series Bedienungsanleitung

ESAB

ESAB PC-900 Bedienungsanleitung

ESAB

ESAB A6 GMD Bedienungsanleitung

ESAB

ESAB PSF 260 Bedienungsanleitung

ESAB

ESAB PREST-O-LITE 02X93 Bedienungsanleitung

ESAB

ESAB SDF-250 Bedienungsanleitung

ESAB

ESAB 1500 ahma Bedienungsanleitung

ESAB

ESAB Arc Master ICE A6 S Bedienungsanleitung

ESAB

ESAB TWECO SPRAY MASTER V250 Wartungs- und Serviceanleitung

ESAB

ESAB MXH 315 PP Bedienungsanleitung

ESAB

ESAB SAVAGE A40 Bedienungsanleitung

ESAB

ESAB A6 S Arc Master Bedienungsanleitung

ESAB

ESAB PSE-10 Bedienungsanleitung

ESAB

ESAB Aristo U8 Bedienungsanleitung

ESAB

ESAB PSF 260C Bedienungsanleitung

ESAB

ESAB CIGWELD 454342 Bedienungsanleitung

ESAB

ESAB Warrior Feed 304 Bedienungsanleitung

ESAB

ESAB PSF 250 Bedienungsanleitung

ESAB

ESAB SDF-50 Bedienungsanleitung

ESAB

ESAB Aristo MA4 Bedienungsanleitung

ESAB

ESAB Aristo U6 Bedienungsanleitung

ESAB

ESAB PSF 250 Bedienungsanleitung

Beliebte Schweißzubehör Handbücher anderer Marken

Lincoln Electric

Lincoln Electric LT-7 Tractor Bedienungsanleitung

Weco

Weco Trolley R Bedienungsanleitung

Cornwell Tools

Cornwell Tools MMWC1 Bedienungsanleitung

Dohle

Dohle ExOn2A Bedienungsanleitung

Nederman

Nederman Fume Eliminator FE 840/2500/P150 Bedienungsanleitung

3M Speedglas 9100 Series Bedienungsanleitung

Miller Electric

Miller Electric OM-842 Bedienungsanleitung

Miller

Miller A-200 Series Bedienungsanleitung

Abicor Binzel

Abicor Binzel ABIMIG WT Series Bedienungsanleitung

optrel

optrel lifeflip autopilot Bedienungsanleitung

Miller

Miller MIGmatic M-25 Bedienungsanleitung

Tregaskiss

Tregaskiss TOUGH GUN TT3 Reamer Bedienungsanleitung

Abicor Binzel

Abicor Binzel xFUME PRO Bedienungsanleitung

Sealey

Sealey SR20.V2 Bedienungsanleitung

iWeld

iWeld NORED EYE Bedienungsanleitung

Sthor

Sthor 74483 Bedienungsanleitung

Leister

Leister TWINNY T7 Bedienungsanleitung

Miller

Miller I-22 CE Bedienungsanleitung