ESAB PC-900 Bedienungsanleitung
Mechanized Conversion Kit Installation Instructions
for PC-900
0558008549 04/2009
2
This equipment will perform in conformity with the description thereof contained in this manual and accompa-
nying labels and/or inserts when installed, operated, maintained and repaired in accordance with the instruc-
tions provided. This equipment must be checked periodically. Malfunctioning or poorly maintained equipment
should not be used. Parts that are broken, missing, worn, distorted or contaminated should be replaced imme-
diately. Should such repair or replacement become necessary, the manufacturer recommends that a telephone
or written request for service advice be made to the Authorized Distributor from whom it was purchased.
This equipment or any of its parts should not be altered without the prior written approval of the manufacturer.
The user of this equipment shall have the sole responsibility for any malfunction which results from improper
use, faulty maintenance, damage, improper repair or alteration by anyone other than the manufacturer or a ser-
vice facility designated by the manufacturer.
BE SURE THIS INFORMATION REACHES THE OPERATOR.
YOU CAN GET EXTRA COPIES THROUGH YOUR SUPPLIER.
These INSTRUCTIONS are for experienced operators. If you are not fully familiar with the
principles of operation and safe practices for arc welding and cutting equipment, we urge
you to read our booklet, “Precautions and Safe Practices for Arc Welding, Cutting, and
Gouging,” Form 52-529. Do NOT permit untrained persons to install, operate, or maintain
this equipment. Do NOT attempt to install or operate this equipment until you have read
and fully understand these instructions. If you do not fully understand these instructions,
contact your supplier for further information. Be sure to read the Safety Precautions be-
fore installing or operating this equipment.
CAUTION
USER RESPONSIBILITY
READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.
PROTECT YOURSELF AND OTHERS!
3
Users of ESAB welding and plasma cutting equipment have the ultimate responsibility for ensuring that
anyone who works on or near the equipment observes all the relevant safety precautions. Safety precautions
must meet the requirements that apply to this type of welding or plasma cutting equipment. The following
recommendations should be observed in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well acquainted with the operation of the welding or plasma
cutting equipment. Incorrect operation of the equipment may lead to hazardous situations which can result in
injury to the operator and damage to the equipment.
1. Anyone who uses welding or plasma cutting equipment must be familiar with:
- its operation
- location of emergency stops
- its function
- relevant safety precautions
- welding and / or plasma cutting
2. The operator must ensure that:
- no unauthorized person stationed within the working area of the equipment when it is started up.
- no one is unprotected when the arc is struck.
3. The workplace must:
- be suitable for the purpose
- be free from drafts
4. Personal safety equipment:
- Always wear recommended personal safety equipment, such as safety glasses, ame proof
clothing, safety gloves.
- Do not wear loose tting items, such as scarves, bracelets, rings, etc., which could become
trapped or cause burns.
5. General precautions:
- Make sure the return cable is connected securely.
- Work on high voltage equipment may only be carried out by a qualied electrician.
- Appropriate re extinquishing equipment must be clearly marked and close at hand.
- Lubrication and maintenance must not be carried out on the equipment during operation.
SAFETY PRECAUTIONS
4
SAFETY PRECAUTIONS
WELDING AND PLASMA CUTTING CAN BE INJURIOUS TO YOURSELF AND
OTHERS. TAKE PRECAUTIONS WHEN WELDING OR CUTTING. ASK FOR
YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE BASED ON
MANUFACTURERS’ HAZARD DATA.
ELECTRIC SHOCK - Can kill.
- Install and earth (ground) the welding or plasma cutting unit in accordance with applicable standards.
- Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
- Insulate yourself from earth and the workpiece.
- Ensure your working stance is safe.
FUMES AND GASES - Can be dangerous to health.
- Keep your head out of the fumes.
- Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS - Can injure eyes and burn skin.
- Protect your eyes and body. Use the correct welding / plasma cutting screen and lter lens and wear
protective clothing.
- Protect bystanders with suitable screens or curtains.
FIRE HAZARD
- Sparks (spatter) can cause re. Make sure therefore that there are no inammable materials nearby.
NOISE - Excessive noise can damage hearing.
- Protect your ears. Use earmus or other hearing protection.
- Warn bystanders of the risk.
MALFUNCTION - Call for expert assistance in the event of malfunction.
READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.
PROTECT YOURSELF AND OTHERS!
WARNING
5
Powercut-900
Mechanized Conversion Kit contents
p/n 0558008284
MECHANIZED CONVERSION KIT INSTALLATION INSTRUCTIONS
Item No. Part No. Qty Description
1 0558038337 1 PC BOARD - REMOTE
2 0558008457 1 RECEPTACLE / CABLE ASSY 14 PIN
3 952002 1 TOROIDAL CORE
4 951016 1 CONNECTOR COMBICON 10 PIN
5 951005 1 CONNECTOR COMBICON 3 PIN
6 526652 1 STRAIN RELIEF SEALED 1/2" ZINC
7 2062151 1 LOCKNUT CONDUIT 1/2"
8 * 0.75" HEATSHRINK 1" BLACK
9 * 1 CLAMP CABLE STEEL .375 DIA
10 * 2 SCREW HEX WSH TAP #8 x .438 RIBBED
11 * 5 TYWRAP SM 4"
12 0558008111 1 KIT JUMPER - MECHANIZED LOGIC
1
2
4
5
6, 7
9
10
11
2
2 wire connector cable
12
38
6
1. Access the inside of the PC-900 by unscrewing the
screws and removing the cover.
2. Assemble the strain relief onto the 14 pin cable as shown and partially tighten.
3. Remove the hole plug on the top right side of the back of the unit.
MECHANIZED CONVERSION KIT INSTALLATION INSTRUCTIONS
7
MECHANIZED CONVERSION KIT INSTALLATION INSTRUCTIONS
4. Cut the tie wrap, unplug control transformer
wires to allow for easier cable routing.
5. Thread the cable through the hole as shown
and allow cable to hang loose. Add locknut
and partially tighten. Add heatshrink to ca-
ble and leave loose, before applying clamp.
6. Assemble the cable clamp onto the exposed shield area and attach to the frame with the screw pro-
vided. Orient clamp downward as shown.
Cable clamp
Cable clamp in postion
Cut the tie wrap here
Heatshrink (leave loose)
8
7. Tighten the strain relief nut from the inside
rst and then tighten the outside strain re-
lief nut. Position heatshrink over threads to
prevent power leads from contacting sharp
edges. Electrical or other suitable tape may be
used if heatshrink gun is not available.
MECHANIZED CONVERSION KIT INSTALLATION INSTRUCTIONS
8. Addtoroidalcoretocableandleaveloose,before
installing connector. Align the 10-pin connec-
tor with the pc board header to identify which
end of the connector is pin 1 and therefore en-
sure proper connections of the 10 cables wires.
9. Install each wire and tighten. Cable wires are numbered 1 through 10 and must be connected in nu-
merical sequence starting with number 1. The pc board has been stamped with numbers 1 and 10 to
show the direction of sequence for the wires.
8
9
10
1
2
3
4
5
6
7
each wire is numbered
Heatshrink or suitable tape
9
Fast-on connectors
MECHANIZED CONVERSION KIT INSTALLATION INSTRUCTIONS
10. Connect the pc board to the main power control board as shown below. Connect the ring terminal
from the 14 pin cable and secure the pc board to the frame with the screw provided.
Install tie wrap as shown by arrow
11. Connect the fast-on connectors of the
"2-wire cable" to the 14 pin cable. Posi-
tion and tie wrap toroidal core.
12. Route the "2-wire cable" under the pc
board and tie wrap to the frame using
the provided holes in the areas shown.
13. Re-install the plug and tie wrap on the
previously unplugged wire.
Toroidal Core
Tie wrap
Tie wrap
10
MECHANIZED CONVERSION KIT INSTALLATION INSTRUCTIONS
red wire "+"
black wire "-"
14. Route the "2-wire cable" downward behind the shelf brace.
15. Locate the 3-pin connector on the existing main power control board.
16. Align the 3-pin connector with the pc board header to identify which end of the connector aligns with
the "+" and "-" on the pc board. On the connector, insert the red wire to the "+" and black wire to the "-"
from the "2-wire cable" as shown and tighten.
17. Plug in the 3-pin connector on the pc board.
3-pin connector
Inhaltsverzeichnis
Andere ESAB Schweißzubehör Handbücher
ESAB
ESAB Eye-Tech 9-13 Bedienungsanleitung
ESAB
ESAB A2 S GMAW Mini Master Bedienungsanleitung
ESAB
ESAB SAVAGE A40 Bedienungsanleitung
ESAB
ESAB A6 GMD Bedienungsanleitung
ESAB
ESAB SDF-250 Bedienungsanleitung
ESAB
ESAB Warrior YardFeed 200 Bedienungsanleitung
ESAB
ESAB PSF 260 Bedienungsanleitung
ESAB
ESAB TIGAID315 AC/DC Bedienungsanleitung
ESAB
ESAB PSE-10 Bedienungsanleitung
ESAB
ESAB Aristo U6 Bedienungsanleitung
ESAB
ESAB SABRE V J28 Bedienungsanleitung
ESAB
ESAB PSF 250 Bedienungsanleitung
ESAB
ESAB Sentinel A50 Bedienungsanleitung
ESAB
ESAB MT-400EHD Bedienungsanleitung
ESAB
ESAB PT-31XL Bedienungsanleitung
ESAB
ESAB CIGWELD 454342 Bedienungsanleitung
ESAB
ESAB Sentinel A60 Bedienungsanleitung
ESAB
ESAB EFU 30 Bedienungsanleitung
ESAB
ESAB Eye-Tech 10-12 Select Bedienungsanleitung
ESAB
ESAB CIGWELD Arcmaster 649 Payday Bedienungsanleitung
Beliebte Schweißzubehör Handbücher anderer Marken
Lincoln Electric
Lincoln Electric LT-7 Tractor Bedienungsanleitung
Weco
Weco Trolley R Bedienungsanleitung
Cornwell Tools
Cornwell Tools MMWC1 Bedienungsanleitung
Dohle
Dohle ExOn2A Bedienungsanleitung
Nederman
Nederman Fume Eliminator FE 840/2500/P150 Bedienungsanleitung
3M
3M Speedglas 9100 Series Bedienungsanleitung
Miller Electric
Miller Electric OM-842 Bedienungsanleitung
Miller
Miller A-200 Series Bedienungsanleitung
Abicor Binzel
Abicor Binzel ABIMIG WT Series Bedienungsanleitung
optrel
optrel lifeflip autopilot Bedienungsanleitung
Miller
Miller MIGmatic M-25 Bedienungsanleitung
Tregaskiss
Tregaskiss TOUGH GUN TT3 Reamer Bedienungsanleitung
