ETC Halcyon Gold Bedienungsanleitung

High End Systems

Halcyon Gold

Automated Luminaire User Manual

Version 1.4.1

Part Number: 2562M1200-1.4.1 Rev: A

Released: 2023-01

To view a list of ETCtrademarks and patents, go to etcconnect.com/ip. All other trademarks, both marked

and not marked, are the property of their respective owners.

You can find complete High End Systems terms and conditions and warranty information at

etcconnect.com/Support/Warranty.aspx.

ETC intends this document, whether printed or electronic, to be provided in its entirety.

Table of Contents

Table of Contents i

Introduction 1

Document Conventions 1

Help from Technical Services 2

Safety Considerations 3

General Operation and Use Guidelines 5

Overview 6

Fixture 6

User Interface 7

Touchscreen Display 7

Navigation Controls 8

Specifications 8

Environment 8

Power 9

Electrical 9

Input and Power Factor 9

Fixtures per Circuit 9

Connector Specifications 9

Install the Fixture 10

DMX Control 13

DMX Connector Pinout 13

Connect DMXCables to Fixture 13

Terminate DMX 14

Set the DMX Start Address 14

DMX Channels 14

Ethernet Control 15

Connect EthernetCables to a Fixture 15

Ethernet Control and DMX Thru 16

Terminate DMX 16

Set the DMX Start Address 16

Set the Control Source and Network 16

Configure the Fixture 17

DMX Address 17

Settings Menu 17

Set Control Options 17

Set Network Options 18

Set Pan and Tilt Options 19

Set Dimming Options 19

Set Fan Options 20

Set Gobo Color Correction 20

Set Units for Temperature Display 20

Set Display Options 20

Update Software 21

Set Calibration 22

Access Service Settings 22

Configure the Encoder 23

Reset Fixture to Factory Default Settings 23

Test/Home Menu 23

Reset the Mechanical Positions on the Fixture 23

Test the Fixture 23

Test an Individual Channel 23

Manually Set an Individual Channel 23

Calibrate Pan and Tilt Encoders 24

Diagnostics Menu 24

View Usage Information 24

View Fixture Errors 24

View Fan Speeds 24

View Sensor Status 25

View Temperatures 25

ii Halcyon Gold User Manual

View DMX Values for Channels 25

View Encoder Information 25

View Software Version 25

View RDM and IP Address Information 25

Configure the Fixture Wirelessly 25

Replace a Gobo 26

Error Codes 26

Maintenance 30

Clean the Fixture 30

Replace the Fuse 30

Replace the Battery 31

Compliance 32

FCC Compliance 32

Table of Contents iii

1 Halcyon Gold User Manual

Introduction

Congratulations on your purchase of the High End Systems Halcyon Gold automated framing

fixture.

This manual provides important information for the safe installation, configuration, and

maintenance of your Halcyon Gold fixture. For your safety, read this entire manual prior to

installing, operating, or servicing the fixture.

Document Conventions

This document uses the following conventions to draw your attention to important

information.

Note:

Notes are helpful hints and information that is supplemental to the main text.

CAUTION: A Caution statement indicates situations where there may be

undefined or unwanted consequences of an action, potential for data loss or

an equipment problem.

CAUTION: Hot Surfaces. This statement indicates that while operating,

equipment surfaces may reach very high temperatures. Allow the

fixture to cool before handling or servicing.

WARNING: A Warning statement indicates situations where damage may

occur, people may be harmed, or there are serious or dangerous

consequences of an action.

WARNING: RISK OF ELECTRIC SHOCK! This warning statement indicates

situations where there is a risk of electric shock.

All ETC High End Systems documents are available for free download from our website:

etcconnect.com/Products/Automated-Fixtures.

Please email comments about this manual to: TechComm@etcconnect.com.

Introduction 2

Help from Technical Services

If you have questions that are not answered by this document, try the ETC support website at

support.etcconnect.com or the High End Systems product website at

etcconnect.com/Products/Automated-Fixtures. If none of these resources are sufficient,

contact ETC Technical Services directly at one of the offices identified below. Emergency

service is available from all offices outside of normal business hours.

When calling for help, take these steps first:

• Prepare a detailed description of the problem

• Go near the equipment for troubleshooting

• Find your notification number if you have called in previously

ETC, Inc.

Americas

Technical Services Department

3031 Pleasant View Road

Middleton, WI 53562

800-775-4382 (USA, toll-free)

+1-608 831-4116

service@etcconnect.com

ETC GmbH

Germany, Austria, Switzerland,

Eastern Europe, and Russia

Technical Services Department

Ohmstrasse 3

83607 Holzkirchen, Germany

+49 (80 24) 47 00-0

techserv-germany@etcconnect.com

ETC Austin

High End Systems Products

Technical Services Department

2105 Gracy Farms Lane

Austin, TX 78758 USA

800-890-8989 (USA, toll-free)

+1-512 836-2242

hesservice@etcconnect.com

ETC France

France

Zone Urbaparc -

Bâtiment E

6 Boulevard de la Libération

Saint-Denis, 93200

+33 1 4243 3535

techservfrance@etcconnect.com

ETC Ltd

Europe, Middle East, and Africa

Technical Services Department

26-28 Victoria Industrial Estate

Victoria Road,

London W3 6UU England

+44 (0)20 8896 1000

techservltd@etcconnect.com

ETCAsia

Asia

Technical Services Department

Room 1801, 18/F

Tower 1, Phase 1 Enterprise Square

9 Sheung Yuet Road

Kowloon Bay, Kowloon, Hong Kong

+852 2799 1220

techserv-asia@etcconnect.com

3 Halcyon Gold User Manual

Safety Considerations

To ensure safe operation, follow the safety instructions and warning notes in the user manual.

• This fixture is intended for professional use only. Not for residential use. Read the entire

manual before using this equipment.

• Contact your authorized ETC dealer or Technical Services before performing any service

in order to maintain warranty coverage.

WARNING: Note the following safety warnings before use:

• This equipment is designed for operation by qualified personnel only.

• Do not stare at the operating lamp. May be harmful to the eyes.

• Replace fuses with the specified type and rating only. See

page 30

• Ensure that the available voltage is within the stated range. See

page 9

• Do not use this fixture with a damaged power lead (cord set). If the lead

is damaged, it must be replaced by a qualified technician with an

equivalent type before use. Contact your local authorized dealer for

replacement power leads.

• Do not use this fixture if the lens is damaged. Damaged lenses must be

replaced before use. Contact your local authorized dealer for a

replacement.

• Do not mount the fixture on or near flammable surfaces.

• The fixture should be positioned so that prolonged staring into the

fixture at a distance closer than 6.4 m (21 ft) is not expected.

• Minimum distance from fixture head to combustible materials:

0.1 m (4 in).

• Minimum distance to lighted objects:3.0 m (9 ft 10 in).

AVERTISSEMENT : Pour votre sécurité, lisez les mises en garde et les avis

suivants avant toute utilisation :

• Cet équipement est conçu pour être utilisé par un personnel qualifié

uniquement.

• Ne regardez pas la lampe en fonctionnement. Peut être nocif pour les

yeux.

• Remplacez les fusibles uniquement par le type et le calibre indiqués.

Voir

page 30

• Veillez à ce que la tension disponible soit dans la plage indiquée. Voir

page 9

• N'utilisez pas ce projecteur avec un cordon d'alimentation endommagé

(fils électriques). Si le cordon est endommagé, un technicien qualifié doit

le remplacer par un cordon de type équivalent avant que l'appareil ne

puisse être utilisé. Contactez votre distributeur agréé local pour obtenir

des cordons d'alimentation de rechange.

• N'utilisez pas cet appareil si la lentille est endommagée. Les lentilles

endommagées doivent être remplacées avant l'utilisation. Contactez

votre revendeur agréé local pour un remplacement.

• Ne pas installer le projecteur sur ou à côté d’une surface inflammable.

• L'appareil doit être positionné de manière à ce qu'un regard prolongé

dans l'appareil à une distance inférieure à 6,4 m (21 pi) soit peu

probable.

• Distance minimum entre la tête du luminaire et les matériaux

combustibles : 0.1 m (4 in).

• Distance minimum avec les objets éclairés :3.0 m (9 ft 10 in).

Safety Considerations 4

WARNING: RISK OF ELECTRIC SHOCK!

• Do not operate this device with the cover open.

• Disconnect the fixture from power and DMX and allow it to cool before

performing any cleaning and maintenance.

AVERTISSEMENT : RISQUE DE CHOC ÉLÉCTRIQUE!

• N'utilisez pas cet appareil avec le couvercle ouvert.

• Débrancher la lampe de son alimentation et du DMX et la laisser

refroidir avant d’effectuer un nettoyage ou un entretien.

RISK GROUP 2: CAUTION. Possibly hazardous optical radiation emitted

from this product. Do not stare at operating lamp. May be harmful to the

eyes.

GROUPE DE RISQUE 2 (RISQUE MODÉRÉ) : ATTENTION. Rayonnement

optique potentiellement dangereux émis par ce produit. Ne regardez pas la

lampe en fonctionnement. Peut être nocif pour les yeux.

CAUTION: Hot Surfaces. Allow the device to cool completely before

handling and servicing.

ATTENTION : Surfaces chaudes. Laissez le luminaire refroidir complètement

avant de le manipuler et de procéder à son entretien.

Note:

The light source in this luminaire is not user-replaceable, and must be

replaced only by a qualified technician. Contact ETC Customer Support for assistance.

Symbols used on the product label are defined below:

3.0 m

The luminaire must be installed at least 3.0m (9ft

10in) away from all lighted objects.

Le luminaire doit être installé à au moins 3,0m

(9pi. 10po.) de tout objet éclairé.

General warning Avertissement général

Do not stare at the operating light source. Ne pas regarder la source de lumière lorsqu’elle

fonctionne.

This product should not be discarded as unsorted

waste but must be sent to separate collection

facilities for recovery and recycling.

Ce produit ne doit pas être jeté avec les déchets

ménagers mais doit être déposé dans une collecte

de déchets électroniques ou dans un point de

collecte.

taor TaRated maximum ambient temperature Température ambiante maximale recommandée

Operate indoors only, not where this product

would be exposed to the weather.

Ne fonctionne qu'à l'intérieur, pas là où ce produit

serait exposé aux intempéries.

5 Halcyon Gold User Manual

General Operation and Use Guidelines

• This fixture is only allowed to be operated with the maximum alternating current that is

stated in the technical specifications label provided on the fixture.

• Lighting effects are not designed for permanent operation. Consistent operation breaks

may extend the life of the fixture.

• When choosing the installation location, make sure the fixture will not be exposed to

extreme heat, moisture, or dust.

• Operate the fixture only after having familiarized yourself with its functions. Do not

permit persons who are not qualified and familiar with its functions to operate the

fixture.

• Do not modify the fixture. Any modifications will void the warranty.

• This manual describes the proper installation and operation of this fixture. Using this

fixture in any way other than the intended use may cause damage and void the warranty.

• When the fixture has been stored or transported in cold temperatures, allow it to warm

to room temperature for a minimum of one hour before applying power. Applying power

to a cold fixture may cause damage to the fixture and void the manufacturer warranty.

• Please use the original packaging if the fixture is to be transported. ETC will not be

responsible for the fixture if packaging other than manufacturer provided packaging is

used.

Inhaltsverzeichnis

Andere ETC Beleuchtungsausrüstung Handbücher

ETC

ETC Selador CE Series Bedienungsanleitung

ETC

ETC HIGH END SYSTEMS SolaPix 37 Bedienungsanleitung

ETC

ETC Cyberlight LED Bedienungsanleitung

ETC

ETC fos/4 Series Bedienungsanleitung

ETC

ETC Source Four Zoom Bedienungsanleitung

ETC

ETC Source Four LED Series Bedienungsanleitung

ETC

ETC Source Four Mini LED Bedienungsanleitung

ETC

ETC Irideon WLZ Bedienungsanleitung

ETC

ETC Source Four HID jr Bedienungsanleitung

ETC

ETC Acclaim 100 series Bedienungsanleitung

ETC

ETC F-Drive W1 Series Bedienungsanleitung

ETC

ETC Source Four LED series Bedienungsanleitung

ETC

ETC fos/4 Series Bedienungsanleitung

ETC

ETC fos/4 Panel Yoke Bedienungsanleitung

ETC

ETC Irideon WLZ Bedienungsanleitung

ETC

ETC CE Source Four Bedienungsanleitung

ETC

ETC Source Four jr Bedienungsanleitung

ETC

ETC ColorSource PAR Bedienungsanleitung

ETC

ETC source four fresnel Bedienungsanleitung

ETC

ETC Source Four LED Series Bedienungsanleitung

ETC

ETC High End Systems SolaFrame 3000 Bedienungsanleitung

ETC

ETC Desire D40XTI Bedienungsanleitung

ETC

ETC Sensor3 Bedienungsanleitung

ETC

ETC Express 24/48 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung