Extech Instruments 407412 Bedienungsanleitung

User's Manual

Hygro Thermo-Anemometer

Model 407412

Model 407412 Version 2.1 July 2006

Warranty

EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in

parts and workmanship for one year from date of shipment (a six month limited warranty

applies to sensors and cables). If it should become necessary to return the instrument for

service during or beyond the warranty period, contact the Customer Service Department at

(781) 890-7440 ext. 210 for authorization or visit our website www.extech.com for contact

information. A Return Authorization (RA) number must be issued before any product is

returned to Extech. The sender is responsible for shipping charges, freight, insurance and

proper packaging to prevent damage in transit. This warranty does not apply to defects

resulting from action of the user such as misuse, improper wiring, operation outside of

specification, improper maintenance or repair, or unauthorized modification. Extech

specifically disclaims any implied warranties or merchantability or fitness for a specific

purpose and will not be liable for any direct, indirect, incidental or consequential damages.

Extech's total liability is limited to repair or replacement of the product. The warranty set

forth above is inclusive and no other warranty, whether written or oral, is expressed or

implied.

Introduction

Congratulations on your purchase of Extech's Hygro Thermo-Anemometer. This Heavy

Duty meter measures and displays Air Velocity + Temperature and Relative Humidity +

Temperature. Air flow can be displayed in the following units of measure: feet per minute,

meters per second, miles per hour, kilometers per hour, and knots. Temperature and RH

units are displayed in oC/oF and % units respectively. This meter is shipped fully tested and

calibrated and, with proper use, will provide years of reliable service.

Specifications

General Specifications

Display Dual function, 4-digit (9999 count) LCD display

Units of measure m/s (meters per second), km/hr (kilometers per hour), ft/min (feet per

minute), knots (nautical miles per hour), mile/hr (miles per hour);

Temperature: °C/°F; Humidity: %RH

Data hold Holds reading on the LCD display when button is pressed

Sensors Air velocity sensor: Twisted vane arm with low friction ball bearing;

Temperature: Precision thermistor; Humidity: Thin film capacitor

Max/Min Record Records highest and lowest readings for later recall

Data Output RS-232 serial PC interface

Operating Temp. 32°F to 122°F (0°C to 50°C)

Operating Humidity Max. 80% RH

Power Supply 9V battery

Power Consumption Approx. 8.3 mA DC

Weight 0.77 lbs. (350g)

Dimensions Meter: 7.1x2.8x1.3" (180 x 72 x 32mm);

Anemometer Probe: 0.7" (17mm) Diameter x 6.7" (170mm)

Accessories Anemometer/temperature and RH Probes, 9V battery, & case

Model 407412 Version 2.1 July 2006

Range Specifications

Air velocity

Measurement Range Resolution Accuracy (% of reading)

ft/min (feet/min) 80 - 4921 ft/min 1 ft/min ± (2% + 20 ft/min)

m/s (meters/sec) 0.4 - 25.00 m/s 0.01 m/s ± (2% + 0.2 m/sec)

km/h (kilometers/hour) 1.4 - 90.0 km/h 0.1 km/h ± (2% + 0.2 km/hr)

mph (miles/hour) 0.9 - 55.9 mph 0.1 mph ± (2% + 0.2 mph)

knots (nautical miles/hour ) 0.8 to 48.6 knots 0.1 knots ± (2% + 0.2 knots)

Temperature

Range Resolution Accuracy

32oF to 122oF (0oC to 50oC) 0.1oF/oC±1.5oF (±0.8oC)

Relative Humidity

Range Resolution Accuracy

10 to 70% RH 0.1% ±3% RH

70 to 95% RH 0.1% ±4% RH

Model 407412 Version 2.1 July 2006

Meter Description

1. Sensor input plug – The Anemometer sensor and the Humidity sensor use the same

jack at the top of the meter.

2. RS-232 PC Interface jack

3. LCD Display

4. Keypad (see below)

POWER Press to turn the meter ON or OFF

HOLD Press to freeze the currently displayed reading

C/F Press to select the temperature unit of measure

RECORD Press to track the MAX and MIN readings

RECALL Press to retrieve the current MAX and MIN memory

FUNCTION Select Humidity (left position) or Air Velocity (right position)

UNIT Select the unit of measure for Air Velocity

5. Battery compartment and tilt sand are located on the back of the meter

6. Rubber protective jacket

7. Vane Anemometer sensor

8. Humidity sensor

Model 407412 Version 2.1 July 2006

airflow

Yellow

Dot

Anemometer and Temperature Operation

1. Insert the Vane sensor into the meter's input jack at the top of the meter.

2. Press the POWER button to turn the instrument on.

3. Select Anemometer (Air Velocity) operation by placing the function slider switch to the

vane icon .

4. Select the temperature units by pressing the °C/°F button. The LCD display will

indicate '°C' or '°F' as selected.

5. Select the air velocity unit of measure by pressing the

UNIT button. With each press the display scrolls

through the units (m/s, km/hr, ft/min, knots, & mile/h).

6. For maximum accuracy, the yellow dot must be on the

exhaust side of the vane as shown.

7. The meter’s LCD will indicate Air Velocity +

Temperature.

Relative Humidity and Temperature Operation

1. Insert the Relative Humidity probe in the input jack at the top of the meter.

2. Press the POWER button to turn on the instrument.

3. Select the Humidity mode of operation by placing the function slider switch to the

RH% position.

4. Select the temperature units by pressing the °C/°F button. The LCD display will

indicate '°C' or '°F' as selected.

5. Hold the probe by the handle in the area to be monitored. The meter will display

Relative Humidity + Temperature.

6. Note that humidity measurements take several minutes to stabilize.

Data Hold

Press the DATA HOLD button to freeze the displayed reading. The DH icon will appear on

the LCD while Data Hold is engaged. Press the DATA HOLD button again to resume

normal operation.

Min/Max Record Mode

When selected, the Record mode stores the highest (Max) and lowest (Min) readings for

later recall. To use Record mode:

1. Press the RECORD button. The REC indicator will appear on the LCD display.

2. Start a measurement session.

3. After the measurement session, press the RECALL button to view the highest (Max)

reading recorded since the RECORD button was pressed. The MAX indicator will

appear to inform the user that the displayed reading is the highest value recorded.

4. Press the RECALL button again to view the lowest reading encountered since the

RECORD key was pressed (the MIN indicator will appear on the LCD to inform the

user that the reading displayed is the lowest value recorded).

5. Press RECORD again to return the meter to normal operation. All stored data will be

cleared and the REC/MIN/MAX icons will disappear from the LCD.

6. Note that putting the meter into the Record mode defeats the Auto Power Off feature.

Model 407412 Version 2.1 July 2006

RS-232 PC Interface

The RS-232 serial data port (3.5mm phono jack) is located at the top of the meter next to

the sensor input jack. The PC interface hardware is intended for use with the Extech Data

Acquisition software package, Part Number 407001 which includes WindowsTM 95 / 98 /

ME / NT / 2000 compatible software and PC interface cable. For more information, contact

Extech or refer to the 407001 User's Manual.

Auto Power Off feature

The Auto Power Off feature automatically turns the meter off after approximately 10

minutes. To defeat this feature, place the meter in Record mode by pressing the RECORD

key once (the REC icon will appear on the LCD). The meter will remain powered as long

as the meter is in the RECORD mode.

Battery Replacement

When it is time to replace the 9V battery, the low battery indicator (LBT) appears in the left-

hand corner of the LCD display. Note that reliable readings can be obtained for several

hours after the first appearance of the low battery indicator.

To replace the battery:

1. Remove the meter's protective rubber holster.

2. Open the battery compartment on the back of the meter using a small coin or a flat

blade screwdriver.

3. Replace the 9V battery, close the compartment, and replace the holster.

Relative Humidity and Temperature Calibration

1. Turn the meter on and select the Humidity mode (RH %) using the Function switch.

2. Use a temperature simulator or calibrator to apply 0.0 ºC to the meter and adjust VR3

for a display of 0.0 ºC.

3. Change the input to 25.0 ºC and adjust VR1 for a display of 25.0 ºC.

4. Change the input to 50.0 ºC and verify a display of 50.0 ºC. Readjust VR3 & VR1 if

necessary.

5. Connect the humidity probe to the unit and place the probe in a controlled 33% RH

environment. Let stabilize for a minimum of 30 minutes and adjust VR5 for a reading of

33.0% RH.

6. Place the probe in a 75% RH environment for a minimum of 30 minutes and adjust “R6

for a reading of 75.0% RH.

7. Verify that the temperature reading is within the published specifications. If not, perform

calibration steps 2 and 3, above, again.

Model 407412 Version 2.1 July 2006



Support line (781) 890-7440

Technical support: Extension 200; E-mail: [email protected]

Repair & Returns: Extension 210; E-mail: repair@extech.com

Product specifications subject to change without notice

For the latest version of this User Guide, Software updates, and other

Up-to-the-minute product information, visit our website: www.extech.com

Extech Instruments Corporation, 285 Bear Hill Road, Waltham, MA 02451

Calibration and Repair Services

Extech offers repair and calibration services for the products we sell. Extech also

provides NIST certification for most products. Call the Customer Service Department for

information on calibration services available for this product. Extech recommends that

annual calibrations be performed to verify meter performance and accuracy.

Model 407412 Version 2.1 July 2006

Appendix

Area equation for rectangular or square ducts

Area equation for circular ducts

Cubic equations

NOTE: Measurements made in inches

must be converted to feet or meters before using the above formulae.

Unit of Measure Conversion Table

m/s ft/min knots km/h MPH

1 m/s 1196.87 1.944 3.6 2.24

1 ft/min 0.00508 10.00987 0.01829 0.01138

1 knot 0.5144 101.27 11.8519 1.1523

1 km/h 0.2778 54.69 0.54 10.6222

1 MPH 0.4464 87.89 0.8679 1.6071 1

Width (W)

Height (H)

Area (A) = Width (W) x Height (H)

CFM (ft3/min) = Air Velocity (ft/min) x Area (ft2)

CMM (m3/min) = Air Velocity (m/sec) x Area (m2) x 60

Radius Area (A) = x r2

Where  = 3.14 and r2= radius x radius

Inhaltsverzeichnis

Andere Extech Instruments Messgerät Handbücher

Extech Instruments

Extech Instruments 407510 Bedienungsanleitung

Extech Instruments

Extech Instruments CO240 Bedienungsanleitung

Extech Instruments

Extech Instruments Oyster 341350A-P Bedienungsanleitung

Extech Instruments

Extech Instruments 38389 Bedienungsanleitung

Extech Instruments

Extech Instruments PH210 Bedienungsanleitung

Extech Instruments

Extech Instruments LT300 Bedienungsanleitung

Extech Instruments

Extech Instruments RH390 Bedienungsanleitung

Extech Instruments

Extech Instruments HT30 Bedienungsanleitung

Extech Instruments

Extech Instruments 382095 Bedienungsanleitung

Extech Instruments

Extech Instruments RH300 Bedienungsanleitung

Extech Instruments

Extech Instruments TachIR RPM10 Bedienungsanleitung

Extech Instruments

Extech Instruments TH10 Bedienungsanleitung

Extech Instruments

Extech Instruments HDV-WTX2 Abmessungen

Extech Instruments

Extech Instruments CO10 Bedienungsanleitung

Extech Instruments

Extech Instruments HD350 Bedienungsanleitung

Extech Instruments

Extech Instruments 380460 Bedienungsanleitung

Extech Instruments

Extech Instruments ExStik EC510 Bedienungsanleitung

Extech Instruments

Extech Instruments EC100 Bedienungsanleitung

Extech Instruments

Extech Instruments 407790A Bedienungsanleitung

Extech Instruments

Extech Instruments SDL710 Bedienungsanleitung

Extech Instruments

Extech Instruments 341350A Bedienungsanleitung

Extech Instruments

Extech Instruments CO210 Bedienungsanleitung

Extech Instruments

Extech Instruments AN250W Bedienungsanleitung

Extech Instruments

Extech Instruments 461893 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung