Fantom FM744HY Leitfaden

USING THE VACUUM CLEANER

EDGE CLEANING

This vacuum cleaner is equipped with an "edge cleaning" function for cleaning carpet edges

near baseboards and stationary furniture.

RUG/FLOOR (TOOLS)SELECTOR

The RUG/FLOOR(TOOLS)selector should only be

adjusted while the vacuum cleaner is turned on

and in the upright position.

When cleaning a rug or carpet,first

turn the ON/OFF switch to the ON

position,and then set the RUG/

FLOOR(TOOLS)selector to the

RUG position.

When cleaning a bare floor or when using

one of the attachments,set the RUG/FLOOR

(TOOLS)selector to the FLOOR position.

Caution: Do not change the setting of the RUG/FLOOR(TOOLS)selector while the vacuum

cleaner is turned off.

Rug/Floor (Tools)

SELECTOR

RUG

FLOOR

(TOOLS)

RUG

Nozzle Head

Height AdjustmentLever

HEIGHT ADJUSTMENT LEVER

The nozzle head can be

adjusted to four different

height settings.

Set the height adjustment to the

appropriate carpet length.

Use the 3 ( )height

setting.

TURN OFF BRUSH ROLL

WHEN USING TOOLS.

Before using the height adj-

ustment lever, please make

sure the nozzle head is tilted

backward from the floor.

Caution:

Caution: When using one of the attachments during cleaning,set the vacuum

cleaner to the upright position.

USING THE ATT ACHMENTS

Press the release button C to

disconnect the handle from the

vacuum cleaner.

Remove the attachments from the

vacuum cleaner.

Caution:

When removing the attachments, pull

them in the directions shown in the

illustration.Pulling them in the wrong

direction or pulling them forcefully may

cause damage to the attachment clamp.

Attach the attachments as shown below.

Hook the hose holder onto the holder mount.

Caution:

Before using the attachments, please make sure

the hose is hooked on the holder mount. Holder

Mount

Hose

Holder

When you have finished using the attachments, replace them

in their original positions as shown on page 4.

Tabs

Groove

Upholstery tool & Dusting brush

To detach the dusting brush from the upholstery tool: Press the

tabs on the brush downward to remove it.

To reattach the dusting brush to the upholstery tool: Insert

the front of the upholstery tool under the hook on the front of the

dusting brush. Press down on the back of the upholstery tool to

snap it into place under the dusting brush tabs.

Suction Hose A

Wand Crevice Tool

Upholstery

Tool

Dusting

Brush

Suction Hose B

Attach the attachments on the handle or

the suction hose B.

Handle

Caution: Before using the suction hose B,

please make sure the handle is

reattached on the body.

Attachment Clamp

Wand

Crevice Tool

Release

Button C

Turbo Brush

USING THE ATTACHMENTS

Caution: When using one of the attachments during cleaning,set the vacuum

cleaner to the upright position.

Hose Attachment

Hose Cuff

Suction Inlet

Suction Hose A Handle

Line up notches

push hose in till it

clicks.

AIR DRIVEN TURBO BRUSH

Using the Unit With Air Driven Turbo Brush

The efficiency of your Air Driven turbo brush depends on the bristle brush rotating at high speed.

Strong air suction is needed to accomplish this. In order to ensure that maximum air suction is

maintained, please read the following instructions:

1. Always empty the dust cup container frequently during use. Follow instructions on dust

container.

2. Ensurethat the rotating brush is kept free of hair and string which may accumulate and

decrease brush performance.

3. Keep Air Driven Turbo Brush turbine free of dirt and foreign matter. (see illustration below

for cleaning instructions.)

IMPORTANT TURBO BRUSH INSTRUCTIONS

The efficiency of your Air Driven Turbo Brush depends on the bristle brush rotating at high

speed. Strong air suction is needed to accomplish this.

In order to ensure that maximum air suction is maintained, please read the following

instructions:

1) Empty the Dust Container frequently during use. Follow instructions for dust container.

2) Ensure that the rotating brush is kept clear of hair and string.

3) Inspect the turbine regularly to ensure that the air passage is free of dirt and debris.

From time to time, the turbine of your Turbo Brush will require cleaning. To do this:

1. Remove the turbo brush from the hose or extension tube.

2. Slide locking latch forward then tilt the top housing of the brush upwards. The top housing is

hinged and will tilt up approximately 45 only.

3. There may be some dust, lint, hair, etc.on the turbine wheel. Remove as much of this as possible.

4. You may also use the unit's hose with crevice tool attached and use the vacuum to remove

any additional debris from the turbine.

5. Ensure that the turbine wheel moves freely by rotating it with your finger. If the turbine does

not rotate, call FANTOM Customer Service for help.

6. Once clean, close the top cover of the Turbo Brush and slide the locking latch toward the rear

of the brush to lock.

Cleaning Air Driven Turbo Brush

Your Air Driven turbo Brush may be used with either the extension tubes or the flexible hose.

Using The Unit With Air Driven Turbo Brush

Turbine

Locking Latch Tilt

Upwards

Inhaltsverzeichnis

Andere Fantom Staubsauger Handbücher

Fantom

Fantom FANTOM FM743H Bedienungsanleitung

Fantom

Fantom FM709K Bedienungsanleitung

Fantom

Fantom FS801 Bedienungsanleitung

Fantom

Fantom FM741B Bedienungsanleitung

Fantom

Fantom FM741 Bedienungsanleitung

Fantom

Fantom PROMAX 800M3 Bedienungsanleitung

Fantom

Fantom BAGLESS STICK VAC FS800 Bedienungsanleitung

Fantom

Fantom FM742CS Bedienungsanleitung

Fantom

Fantom PROMIDI 600M2 Bedienungsanleitung

Fantom

Fantom FM766HG Bedienungsanleitung

Fantom

Fantom FM741HR Bedienungsanleitung

Fantom

Fantom FM741HV Bedienungsanleitung

Fantom

Fantom FM740 Bedienungsanleitung

Fantom

Fantom FM732C Bedienungsanleitung

Fantom

Fantom FM142EF Bedienungsanleitung

Fantom

Fantom FM742H Bedienungsanleitung

Fantom

Fantom PROVAC P 5000 Bedienungsanleitung

Fantom

Fantom TRANSFORMER VAC FM604 Bedienungsanleitung

Fantom

Fantom VACUUM CLEANER FM744HY Bedienungsanleitung

Fantom

Fantom FM310K Bedienungsanleitung

Fantom

Fantom VACUUM CLEANER FM766 Bedienungsanleitung

Fantom

Fantom 14.4 V DC Bedienungsanleitung

Fantom

Fantom FM760 Bedienungsanleitung

Fantom

Fantom FM788HB Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung