Federal Signal Corporation Vision SLR Betriebsanleitung

2562543 Rev. A1 0620

Safety Message to Installers of Federal Signal Warning Light Systems

People’s lives depend on your proper installation and servicing of Federal Signal products. It is important

to read and follow all instructions shipped with this product and the original product. Listed below are

some other important safety instructions and precautions you should follow.

• To properly install a light assembly, you must have a good understanding of automotive electrical

procedures and systems, along with proﬁciency in the installation and use of safety warning

equipment.

• Do not install equipment or route wiring in the deployment path of an airbag. Failure to observe this

warning will reduce the eectiveness of the airbag or potentially dislodge the equipment, causing

serious injury.

• If a vehicle seat is temporarily removed, verify with the vehicle manufacturer if the seat needs to be

recalibrated for proper airbag deployment.

• This product contains high intensity LED devices. To prevent permanent eye damage, DO NOT stare

into the light beam at close range.

• Always refer to the vehicle service manuals when performing equipment installations on a vehicle.

• Never attempt to install aftermarket equipment that connects to the vehicle wiring without reviewing

a vehicle wiring diagram available from the vehicle manufacturer. Ensure that your installation will not

aect vehicle operation or mandated safety functions or circuits. Always check the vehicle for proper

operation after installation.

• When drilling into a vehicle structure, ensure that both sides of the surface are clear of anything that

could be damaged.

• A light system is a high current device. In order for it to function properly, a separate ground

connection must be made. If practical, it should be connected to the negative battery terminal. At a

minimum, it may be attached to a solid metal body or chassis part that will provide an eective ground

path as long as the light system is to be used.

• Locate the light system controls so the VEHICLE and CONTROLS can be operated safely under all driving

conditions.

• Do not attempt to activate or deactivate the light control while driving in a hazardous situation.

• For additional precautions and information, refer to the instructions packed with related products.

• Frequently inspect the light system to ensure that it is operating properly and that it is securely

attached to the vehicle.

• File these instructions in a safe place and refer to them when maintaining or reinstalling the product.

Failure to follow all safety precautions and instructions may result in property damage, serious injury, or

death.

Vision®SLR with Standalone

SignalMaster®Supplement

Vision®SLR with Standalone SignalMaster®Supplement

2Vision SLR with Standalone SignalMaster

Federal Signal www.fedsig.com

Introduction

This publication provides supplemental instructions for installing the Vision SLR light bar with Standalone

SignalMaster to a vehicle.

Unpacking the Kit

After unpacking the kit, inspect it for damage that may have occurred in transit. If it has been damaged,

ﬁle a claim immediately with the carrier stating the extent of the damage. Carefully check all envelopes,

shipping labels, and tags before removing or destroying them. Ensure that the parts shown in Table 1 are

contained in the packing carton. If you are missing any parts, contact Customer Support at

1-800-264-3578, 7 a.m. to 5 p.m., Monday through Friday (CT). An installer-supplied control head for

controlling the functions of the light bar is also required.

Table 1 Kit contents

Qty. Description Part No.

1 Eight-Position Female Connector 140325-06

1 Eight-Position Male Connector 140333-08

2 Mounting Bracket 8652180

4 #10 Type B Pan Head Torx®Black Stainless Steel Screw 7011246-06

2 1/4-20 Stainless Steel Keps®Nuts 7058050

Mounting the SignalMaster

LOCATING OPERATOR CONTROLS: Locate the light system controls so the vehicle and

controls can be operated safely under all driving conditions. Failure to heed this warning could

result in driver distraction or driver error while operating the vehicle.

ROOF SUPPORT STRUCTURE: There is a roof support member that spans the distance between

the driver and passenger side. DO NOT DRILL THROUGH THIS MEMBER! Adjust any hole

locations until the holes can be drilled without going through this member. Failure to follow this

warning will weaken the roof of the vehicle and may lead to an increased chance of bodily injury

or death in a rollover accident.

SIGNALMASTER ORIENTATION: The SignalMaster light bar must be oriented correctly for

proper operation. The assembly should be installed with the ROC board on top.

IMPORTANT: Plan all cable routing before completing the installation. Plan the location of the wire

routing hole so that the cable does not have tight bends.

To mount the SignalMaster:

1. Determine the desired distance between the mounting holes and attach the mounting brackets to

the SignalMaster with the #10 Torx screws.

2. Mark the positions of the two mounting holes and the hole for the cable.

3. Drill two mounting holes 0.257 inch to 0.265 inch in diameter and a hole 0.375 inch in diameter for

the cable.

Vision®SLR with Standalone SignalMaster®Supplement

Vision SLR with Standalone SignalMaster

Federal Signal www.fedsig.com

4. Secure the SignalMaster to the vehicle with the 1/4-20 Keps®nuts.

Figure 1 Mounting brackets attached to SignalMaster

#10 TORX SCREW (4)

MOUNTING BRACKET (2)

SIGNALMASTER

ALUMINUM EXTRUSION

STUD FOR 1/4"-20 KEP NUT

290A6778

Connecting the 8-Position Connectors

CONNECTOR PRECAUTION: The eight-position connector is not waterproof. Before cutting the

SignalMaster cable, determine the cable lengths required to ensure that the cable connector is

located in a dry location inside the vehicle.

To electrically connect the SignalMaster to the Vision SLR:

1. Cut the SignalMaster cable to length and route it to the chosen connection point.

2. Strip and connect the eight SignalMaster control wires as shown in Figures 2 and 3. Keep the pairs

twisted together, separating them just enough to insert the ends into the connector.

Figure 2 Connections between Vision SLR and SignalMaster

290A6427

FROM

SIGNALMASTER

SYSTEM

RED

YEL

WHT

GRN

LT BLU

BRN

BLK

ORG

140333-08 140325-06

RED

YEL

WHT

GRN

LT BLU

BRN

BLK

ORG

FROM VISON SLR

Vision®SLR with Standalone SignalMaster®Supplement

4Vision SLR with Standalone SignalMaster

Federal Signal www.fedsig.com

Figure 3 Wires inserted into connector

290A6428

TIP OF SMALL

SCREWDRIVER

STRIPPED

WIRES 1. INSERT SCREWDRIVER

TIP INTO RECTANGULAR

HOLE.

2. INSERT STRIPPED WIRE

END IN ROUND HOLE.

3. REMOVE SCREWDRIVER.

1/4"

WIRE STRIPPING

TYPICAL

3. Ensure that each SignalMaster control wire is in the proper position. Connect the eight-position

connectors together, and apply pressure until they lock.

4. After installation, test the light system to ensure that it is operating properly.

5. Test all vehicle functions, including horn operation, vehicle safety functions, and vehicle light systems,

to ensure proper operation. Ensure that the installation has not aected the vehicle operation or

changed any vehicle safety function or circuit.

Vision®SLR with Standalone SignalMaster®Supplement

Vision SLR with Standalone SignalMaster

Federal Signal www.fedsig.com

Safety Message to Installers of Federal Signal Warning Light Systems

The lives of people depend on your safe operation of Federal Signal Products. It is important to read and

follow all instructions shipped with the products. In addition, listed below are some other important safety

instructions and precautions you should follow:

• Although your warning system is operating properly, it may not be completely eective. People may

not see or heed your warning signal. You must recognize this fact and continue driving cautiously.

• Situations may occur which obstruct your warning signal when natural or man-made objects are

between your vehicle and others, such as: raising your hood or trunk lid. If these situations occur, be

especially careful.

• This product contains high intensity LED devices. To prevent eye damage, DO NOT stare into the light

beam at close range.

• At the start of your shift, you should ensure that the light is securely attached and operating properly.

RETAIN AND REFER TO THIS MESSAGE

Vision®SLR with Standalone SignalMaster®Supplement

6Vision SLR with Standalone SignalMaster

Federal Signal www.fedsig.com

Ordering Replacement Parts

To order replacement parts, please contact your local dealer/distributor or:

Customer Support

Federal Signal Corporation

Phone: 1-800-264-3578

7 a.m. to 5 p.m., Monday through Friday (CT)

Getting Technical Support

For technical support, please contact:

Federal Signal Corporation

Service Department

Phone: 1-800-433-9132

Fax: 1-800-343-9706

Email: [email protected]

Getting Repair Service

The Federal Signal factory provides technical assistance with any problems that cannot be handled

locally. Any product returned to Federal Signal for service, inspection, or repair must be accompanied

by a Return Material Authorization (RMA). Obtain a RMA from a local Distributor or Manufacturer’s

Representative. Provide a brief explanation of the service requested, or the nature of the malfunction.

Address all communications and shipments to the following:

Federal Signal Corporation

Service Department

2645 Federal Signal Dr.

University Park, IL 60484-3167

Vision®SLR with Standalone SignalMaster®Supplement

Vision SLR with Standalone SignalMaster

Federal Signal www.fedsig.com

Limited Warranty

This product is subject to and covered by a limited warranty, a copy of which can be found at

www.fedsig.com/SSG-Warranty. A copy of this limited warranty can also be obtained by written request to

Federal Signal Corporation, 2645 Federal Signal Drive, University Park, IL 60484, email to

[email protected] or call +1 708-534-3400.

This limited warranty is in lieu of all other warranties, express or implied, contractual or statutory,

including, but not limited to the warranty of merchantability, warranty of ﬁtness for a particular purpose

and any warranty against failure of its essential purpose.

2645 Federal Signal Drive

University Park, Illinois 60484-3167

www.fedsig.com

Customer Support

Police/Fire-EMS: 800-264-3578 • +1 708 534-3400

Work Truck: 800-824-0254 • +1 708 534-3400

Technical Support: 800-433-9132 • +1 708 534-3400

All product names or trademarks are property of their respective owners.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Federal Signal Corporation Autozubehör Handbücher

Federal Signal Corporation

Federal Signal Corporation HighLighter Montageanleitung

Federal Signal Corporation

Federal Signal Corporation DFC-WC-DUR21 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Cuda TriOptic 351014F Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation ESB-CRG07 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation GHSCENE Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation CAMLCD-AHD-70 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation XHK-SD Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation VSLR1-IPX Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation ML-PT Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation VIPER EXT Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation GH1K Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Commander 371LED-120B Handbuch

Federal Signal Corporation

Federal Signal Corporation RAYDIAN Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Viewpoint FV Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Fireball FB2LED Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Vista Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation ESB-IMP08R Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SIFMH Handbuch

Federal Signal Corporation

Federal Signal Corporation Cuda TriOptic SIGNALMASTER 328823F Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation 7000 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation DFC Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SpectraLux SIFZJ FSJoin Handbuch

Federal Signal Corporation

Federal Signal Corporation JetSolaris JLX Series Handbuch

Federal Signal Corporation

Federal Signal Corporation SpectraLux SIFZ Front ILS Handbuch

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung