Federal Signal Corporation Split Vision VSLR3 Bedienungsanleitung

Safety Message to Installers of Warning Light Equipment

People’s lives depend on your proper installation and servicing of Federal Signal products. It is important

to read and follow all instructions shipped with this product and the original product. Listed below are

some other important safety instructions and precautions you should follow.

• To properly install the lighting system, you must have a good understanding of automotive systems,

along with proﬁciency in the installation and use of safety warning equipment.

• Do not install equipment or route wiring in the deployment path of an airbag.

• If a vehicle seat is temporarily removed, verify with the vehicle manufacturer if the seat needs to be

recalibrated for proper airbag deployment.

• Frequently inspect the light system to ensure that it is operating properly is securely attached to the

vehicle.

• When drilling into a vehicle structure, ensure that both sides of the surface are clear of anything that

could be damaged.

• Refer to the instructions packed with related products for additional precautions and information.

• File these instructions in a safe place and refer to them when maintaining and/or reinstalling the

product.

• Do not stare directly into the lights at a close range, or permanent damage to your eyesight may

occur.

Failure to follow all safety precautions and instructions may result in property damage, serious injury, or

death.

Product Overview

This publication has instructions for permanently mounting the Split Vision SLR to a vehicle. One kit is

supplied with VSLR3, and two kits with VSLR6 and VSLR8 models. For electrical installation instructions,

refer to the installation and maintenance instructions packed with the light bar.

Unpacking the Kit

After unpacking the kit, inspect it for damage that may have occurred in transit. If it has been damaged,

do not attempt to install or operate it. File a claim immediately with the carrier, stating the extent of the

damage. Carefully check all envelopes, shipping labels, and tags before removing or destroying them.

Ensure that the parts in the Kit Contents List are included in the package. If you are missing any parts,

contact Customer Support at 1-800-264-3578, 7 a.m. to 5 p.m., Monday through Friday (CT).

Permanent Mounting Kit for the

Split Vision SLR

2562677 A3 0620

Permanent Mounting Kit for the Split Vision SLR

2VSLR3, VSLR6, and VSLR8 Mounting Kits

Federal Signal www.fedsig.com

Table 1 Mounting kit contents

One kit is supplied with VSLR3, and two kits with VSLR6 and VSLR8 models.

Qty. Description Part Number

4 Screw, 1/4 x 3/4 inch, Type AB, HWH, SS BLK OX 7011183-12

8 Pad, Mounting, Rubber 8422A033

4 Nut, Hex, 3/8-16, HCR 7059124

4 Washer, 3/8, S.S 7072A035

4 Lockwasher, Split, 3/8 inch, S.S. 7074A046

1 Bracket, Mounting, LH 8652206-L

1 Bracket, Mounting, RH 8652206-R

Optional Brackets

Qty. Description Part Number

1 Bracket, Short, Mounting, LH 865200957-L

1 Bracket, Short, Mounting, RH 865200957-R

Installing the Mounting Brackets on the Light Bar

To install the mounting brackets on the light bar:

1. Carefully turn the light assembly upside down and place it on a surface that will not scratch the

domes.

2. Assemble one LH and RH mounting bracket on the factory installed carriage bolts using 3/8-16 hex

nuts, 3/8-inch ﬂat washers, and 3/8-inch split lockwashers as shown in Figures 1 and 2. Secure the

brackets in position; torque the nuts to 20 ft-lb.

Figure 1 RH bracket attached to passenger side of light bar

RH Mounting Bracket

Carriage Bolt (4)

(Supplied with Light Bar)

3/8-16 Hex Nut

3/8-inch Split Lockwasher

3/8-inch Washer

290A6847

3. For the Model VSLR6 and VSLR8, repeat steps 1 and 2 on the other half of the light bar.

Permanent Mounting Kit for the Split Vision SLR

VSLR3, VSLR6, and VSLR8 Mounting Kits

Federal Signal www.fedsig.com

Installing the Light Bar on the Vehicle

ROOF SUPPORT STRUCTURE: There is a roof support member that spans the distance between

the driver and passenger side. DO NOT DRILL THROUGH THIS MEMBER! Adjust any hole

locations until the holes can be drilled without going through this member. Failure to follow this

warning will weaken the roof of the vehicle and may lead to an increased chance of bodily injury

or death in a rollover accident.

HEAVY OBJECT: Use lifting aids and proper lifting techniques when removing or replacing the

light bar. Failure to follow this warning may cause personal injury.

To install the light bar on the vehicle.

1. Position the light bar on the vehicle roof at the desired location. The light bar should be positioned

with the pods aligned facing forward. Ensure that the light bar does not interfere with the operation

of other apparatus. See Figure 2.

Figure 2 Light bar with brackets installed

RH Mounting Bracket

LH Mounting Bracket

Side View, Passenger Side

290A6848

Front

Large Offset,

Front

Bottom View, Passenger Side

DRILLING PRECAUTIONS: Before drilling holes, check the area into which you plan to drill to

ensure that you do not damage vehicle components. All drilled holes should be deburred and all

sharp edges should be smoothed. All wires going through drilled holes should be protected by

a grommet or convolute/split-loom tubing.

2. Using the mounting brackets as templates, scribe four drill position marks on the mounting surface.

3. For VSLR6 and VSLR8 models, repeat steps 1 and 2 on the other half of the light bar.

4. Before drilling, move the light bar(s) out of the way. Drill 0.199-inch (#8 drill) diameter holes at the

scribed drill position marks.

5. Place the light bar in position on the roof. For proper drainage, tilt the nose of the light bar downward,

using three mounting pads in back and one mounting pad in front on each bracket.

Permanent Mounting Kit for the Split Vision SLR

4VSLR3, VSLR6, and VSLR8 Mounting Kits

Federal Signal www.fedsig.com

6. Secure the light bar to the roof using the 1/4 by 3/4-inch black stainless steel thread-forming screws

and tighten them securely. The Split Vision SLR should now be solidly anchored to the roof. See

Figure 3.

Figure 3 Bracket secured to vehicle roof

Mounting Bracket

Thread-Forming Screw

ehicle Roof

Mounting Pads

(3 in Back, 1 in Front)

7. Ensure that all fasteners are tightened properly.

IMPORTANT: Frequently inspect the light bar to ensure that all fasteners and brackets are tight.

Getting Technical Support

For technical support, please contact:

Federal Signal Corporation

Service Department

Phone: 1-800-433-9132

Fax: 1-800-343-9706

Email: [email protected]

Getting Repair Service

The Federal Signal factory provides technical assistance with any problems that cannot be handled

locally. Any product returned to Federal Signal for service, inspection, or repair must be accompanied

by a Return Material Authorization (RMA). Obtain a RMA from a local Distributor or Manufacturer’s

Representative. Provide a brief explanation of the service requested, or the nature of the malfunction.

Address all communications and shipments to the following:

Federal Signal Corporation

Service Department

2645 Federal Signal Dr.

University Park, IL 60484-3167

2645 Federal Signal Drive

University Park, Illinois 60484-3167

www.fedsig.com

Customer Support

Police/Fire-EMS: 800-264-3578•+1708534-3400

WorkTruck:  800-824-0254•+1708534-3400

TechnicalSupport: 800-433-9132•+1708534-3400

Andere Handbücher für Split Vision VSLR3

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Federal Signal Corporation Beleuchtungsausrüstung Handbücher

Federal Signal Corporation

Federal Signal Corporation FHL-TAIL Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation QuadraFlare QL64Z3V-LI Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Spire 200 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation GL5 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation MB-IDENT03 Handbuch

Federal Signal Corporation

Federal Signal Corporation SLR LED Handbuch

Federal Signal Corporation

Federal Signal Corporation AV1-LED Handbuch

Federal Signal Corporation

Federal Signal Corporation Electraray 225XL Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Vision SLR Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation 121X Series Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation Vitalite 121SLED Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SIGNALMASTER SML6-2SML1F Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation CN SignalMaster Handbuch

Federal Signal Corporation

Federal Signal Corporation CN SignalMaster FSJoin Handbuch

Federal Signal Corporation

Federal Signal Corporation 151XST Series Handbuch

Federal Signal Corporation

Federal Signal Corporation AD Series Handbuch

Federal Signal Corporation

Federal Signal Corporation Signalmaster SMC14 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Global Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation CUDA TRIOPTIC 351012 Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SIGNALMASTER SM518A Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation GH1 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation IPX6 IMPAXX Handbuch

Federal Signal Corporation

Federal Signal Corporation Signalmaster 331114 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation G-STR-024-D-C Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung