Federal Signal Corporation Spire 200 Bedienungsanleitung

25500545

Rev. A0 0819

Printed in U.S.A

Installation and Maintenance Instructions

Spire™200 Beacon

Las instrucciones en español comienzan en la página 21

Pour voir ce manuel en français, allez à www.fedsig.com

Installation and Maintenance Instructions

Spire™200 Beacon

Federal Signal www.fedsig.com

Limited Warranty

This product is subject to and covered by a limited warranty,

a copy of which can be found at www.fedsig.com/SSG-Warranty.

A copy of this limited warranty can also be obtained by written

request to Federal Signal Corporation, 2645 Federal Signal Drive,

University Park, IL 60484, email to info@fedsig.com or

call +1 708-534-3400.

This limited warranty is in lieu of all other warranties, express or

implied, contractual or statutory, including, but not limited to the

warranty of merchantability, warranty of ﬁtness for a particular

purpose and any warranty against failure of its essential purpose.

2645 Federal Signal Drive

University Park, Illinois 60484

www.fedsig.com

Customer Support

Police/Fire-EMS: 800-264-3578•+1708534-3400

WorkTruck: 800-824-0254•+1708534-3400

TechnicalSupport 800-433-9132•+1708534-3400

Installation and Maintenance Instructions

Spire™200 Beacon

Federal Signal www.fedsig.com

Contents

Safety Message to Installers and Service Personnel.....................4

Overview of the Spire™ 200 Beacon ...............................................7

Unpacking the Beacon......................................................................7

Attaching the Optional Mounting Flange to the

Beacon................................................................................................8

Wiring the Beacon...........................................................................10

Permanently Mounting the Beacon ............................................... 11

Pipe Mounting the Beacon .............................................................14

Using Magnetic or Magnetic/Suction Mounting ..........................14

Conguring the Beacon..................................................................15

Selecting a Flash Pattern................................................................15

Selecting Sync or Alt.......................................................................16

Selecting Single or Dual Color (if equipped) ................................17

Selecting the Color Order...............................................................17

Resetting the Beacon to the Default Settings...............................17

Cleaning the Beacon.......................................................................19

Getting Technical Support.............................................................. 19

Figures

Figure 1 Optional Mounting Flange ....................................................9

Figure 2 Flange Base .........................................................................9

Figure 3 Drilling (Not to scale)......................................................12

Figure 4 Permanent-mount beacon (exploded view).......................13

Tables

Table 1 Product Specications............................................................ 7

Table 2 Mounting kit hardware for permanent mounted beacons...... 8

Table 3 Wire Connections................................................................ 10

Table 4 Flash Patterns ...................................................................... 18

Installation and Maintenance Instructions

Spire™200 Beacon

Federal Signal www.fedsig.com

Safety Message to Installers and Service Personnel

People’s lives depend on your proper installation and servicing

of Federal Signal products. It is important to read and follow all

instructions shipped with this product. In addition, listed below

are some other important safety instructions and precautions

you should follow:

• To properly install or service this equipment, you must have a

good understanding of automotive mechanical and electrical

procedures and systems, along with proﬁciency in the

installation and service of safety warning equipment. Always

refer to the vehicle’s service manuals when performing

equipment installations on a vehicle.

• To be an eective warning device, this product produces

bright light that can be hazardous to your eyesight when

viewed at a close range. Do not stare directly into this

lighting product at a close range, or permanent damage to

your eyesight may occur.

• Do not install the light system in an area that would block,

impair, or blind the driver’s vision. Ensure that the light

system is mounted in a position that is outside the driver’s

ﬁeld of vision so the driver can safely operate the vehicle.

• A light system is a high current system. For the system

to function properly, a separate negative (–) connection

and positive (+) connection must be made. All negative

connections should be connected to the negative battery

terminal, and a suitable fuse should be installed on the

positive battery terminal connection as close to the battery

as possible. Ensure that all wires and fuses are rated

correctly to handle the device and system amperage

requirements.

• Never attempt to install aftermarket equipment that connects

to the vehicle wiring without reviewing a vehicle wiring

diagram available from the vehicle manufacturer. Ensure that

Installation and Maintenance Instructions

Spire™200 Beacon

Federal Signal www.fedsig.com

your installation will not aect vehicle operation or mandated

safety functions or circuits. Always check the vehicle for

proper operation after installation.

• The lighting system components, especially the outer

housing, get hot during operation. Be sure to disconnect

power to the system and allow the system to cool down

before handling any components of the system.

• Do not mount a radio antenna within 18 inches (45.7 cm)

of the lighting system. Placing the antenna too close to

the lighting system could cause the lighting system to

malfunction or be damaged by strong radio ﬁelds. Mounting

the antenna too close to the lighting system may also cause

the radio noise emitted from the lighting system to interfere

with the reception of the radio transmitter and reduce radio

reception.

• Do not attempt to wash any unsealed electrical device while

it is connected to its power source.

• DO NOT connect this system to the vehicle battery until

ALL other electrical connections are made, mounting of

all components is complete, and you have veriﬁed that no

shorts exist. If the wiring is shorted to the vehicle body or

frame, high current conductors can cause hazardous sparks,

resulting in electrical ﬁres or ﬂying molten metal.

• DO NOT install equipment or route wiring (or the plug-in

cord) in the deployment path of an airbag.

• Before drilling into a vehicle structure, be sure that both

sides of the surface are clear of anything that could be

damaged. Remove all burrs from drilled holes. To prevent

electrical shorts, grommet all drilled holes through which

wiring passes. Ensure that the mounting screws do not cause

electrical or mechanical damage to the vehicle.

• Because vehicle roof construction and driving conditions

vary, do not drive a vehicle with a magnetically mounted

Installation and Maintenance Instructions

Spire™200 Beacon

Federal Signal www.fedsig.com

warning light installed. The light could ﬂy o the vehicle,

causing injury or damage. Repair of damage incurred

because of ignoring this warning shall be the sole

responsibility of the user.

• Locate the light system controls so the VEHICLE and

CONTROLS can be operated safely under all driving

conditions.

• After installation, test the light system to ensure that it is

operating properly.

• Test all vehicle functions, including horn operation, vehicle

safety functions, and vehicle light systems to ensure proper

operation. Ensure that the installation has not aected the

vehicle operation or changed any vehicle safety function or

circuit.

• Scratched or dull reﬂectors or lenses will reduce the

eectiveness of the lighting system. Avoid heavy pressure

and the use of caustic or petroleum-based products when

cleaning the lighting system.

• Replace any optical components that may have been

scratched or crazed during system installation.

• Do not attempt to activate or deactivate the light system

controls while driving in a hazardous situation.

• You should frequently inspect the light system to ensure that

it is operating properly and that it is securely attached to the

vehicle.

• After installation and testing are complete, provide a copy

of these instructions to instructional sta and all operating

personnel.

• File these instructions in a safe place and refer to them when

maintaining and/or reinstalling the product. Failure to follow

all safety precautions and instructions may result in property

damage, serious injury, or death.

Installation and Maintenance Instructions

Spire™200 Beacon

Federal Signal www.fedsig.com

Overview of the Spire™200 Beacon

The beacon uses an LED light source to provide a reliable

signal with 25 selectable ﬂash patterns. The beacon may be

ﬂush mounted, pipe mounted, or attached to brackets. Optional

plastic or aluminum mounting ﬂanges are available. The light

can also be ordered with magnetic mounts or magnetic suction

mounts. The light can operate on a nominal 12 or 24 Vdc power

source. A ﬁve-conductor cable protrudes from the base. This

beacon features FSLink™. It can be synchronized with up to

three other FSLink products. Optional branch guards and dust

covers are also available.

Table 1 Product Specications

Input Voltage 11 to 28 Vdc

12.8 or 25.6 Vdc nominal at 1.25 A

Fuse 2.0 A

Height

Tall beacon:

7.10 inches (18.034 cm) with ange

6.15 inches (15.621 cm) tall without ange

Short beacon:

5.60 inches (14.224 cm) with ange

4.65 inches (14.351 cm) without ange

Diameter 6.54 in with ange

5.22 in without ange

Weight 0.75-2.0 lb (0.34-0.91 kg)

Approvals Marked on product

Unpacking the Beacon

After unpacking the beacon, inspect it for damage that

may have occurred in transit. If there is damage, ﬁle a claim

immediately with the carrier, stating the extent of damage.

Carefully check all envelopes, shipping labels, and tags before

removing or destroying them. If installing a permanent mounted

beacon, ensure that the parts listed in Table 2 are included in

the package.

Installation and Maintenance Instructions

Spire™200 Beacon

Federal Signal www.fedsig.com

Table 2 Mounting kit hardware for permanent mounted beacons

Qty.Description

Basic parts included with permanent mount beacons

3#8 Panhead Phillips Screw

3#10 Panhead Phillips Screw

Additional parts included with mounting anges

3#10 Machine Screws, 1-3/4" long

3#10 Machine Screws, 7/8" long

3#10 Machine Nuts

Attaching the Optional Mounting Flange to the

Beacon

If the optional mounting ﬂanges are to be used, you can either

attach them to the beacon before installation or attach the

ﬂange to the vehicle ﬁrst.

DO NOT DRIVE WITHOUT FIRST MOUNTING THE BEACON TO

THE FLANGE: Because vehicle roof construction and driving

conditions vary, do not drive a vehicle if the beacon is not

attached to the ange. The beacon could y off the vehicle,

causing injury or damage. Repair of damage incurred because of

ignoring this warning shall be the sole responsibility of the user.

1. To attach the ﬂange, locate the detent on the beacon and

one of the two detent notches on the ﬂange.

2. Align the beacon as shown in Figure 1.

3. Push the beacon down completely and turn clockwise 1/8

turn until the detent locks in place.

Installation and Maintenance Instructions

Spire™200 Beacon

Federal Signal www.fedsig.com

Figure 1 Optional Mounting Flange

To remove the beacon from the ﬂange:

1. Use a ﬂat-tipped screwdriver to push the detent while

turning the beacon counterclockwise.

2. Pull up when the detent is free of the notch.

If desired, permanently lock the ﬂange to the base using the

three #8 screws provided. See Figure 2.

Figure 2 Flange Base

Installation and Maintenance Instructions

Spire™200 Beacon

Federal Signal www.fedsig.com

Wiring the Beacon

REVERSE POLARITY/MISWIRING: To avoid damage to the light,

ensure that the input voltage is the same as the voltage rating of

the light. Ensure that correct polarity is observed. Also ensure

that the unit is properly fused with a 2.0-amp fuse.

Table 3 Wire Connections

Color Description Connection Point

Black Ground Battery Negative

Red Mode 1 Switched Positive

12-24 Vdc

White Mode 2 Switched Positive

12-24 Vdc

Brown Low Power Switched Positive

12-24 Vdc

Green Program/

FSLink

12-24 Vdc

To wire the beacon:

1. Determine the required functions and the length of wires

needed to access them. A ﬁve-conductor cable can be

selected for a full-featured installation. For lengths up to

15 feet (5 m), use minimum 18 AWG (1 mm2) wire. For lengths

over 15 feet, use minimum 16 AWG (1.5 mm2) wire. Before

wiring the beacon, refer to Table 3 for the function of each

wire.

2. Strip 1/4 inch (5 mm) of insulation from the ends of the

installer-supplied wires.

3. Use insulated butt connectors to connect the wires to the

power cable of the beacon. Ensure that the connectors are

securely crimped and properly insulated.

4. Connect the end of the fuse holder to the positive (+)

terminal of the voltage source.

Inhaltsverzeichnis

Sprachen:

Andere Federal Signal Corporation Beleuchtungsausrüstung Handbücher

Federal Signal Corporation

Federal Signal Corporation VITALITE 121 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Cuda TriOptic 351012F Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Commander 371ST-250 Handbuch

Federal Signal Corporation

Federal Signal Corporation Viper SignalMaster Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation G-STR-024-D-C Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SIGNALMASTER SM518A Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Cuda Trioptic 352012 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation VISTA 581016-OHP Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation NightSpire Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation CN SignalMaster Handbuch

Federal Signal Corporation

Federal Signal Corporation CudaTriOptic 352212 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation QL43 Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation Vitalite 121SLED Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation AD Series Handbuch

Federal Signal Corporation

Federal Signal Corporation VECTOR Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Vision SLR Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation XStream XSM Series Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation IPX6 IMPAXX Handbuch

Federal Signal Corporation

Federal Signal Corporation SIGNALMASTER SML6-2SML1F Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation ELECTRARAY 225X Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation ILSFFVHL-CH08 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SLR LED Handbuch

Federal Signal Corporation

Federal Signal Corporation GH1 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Signalmaster 330103 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung