FIBARO FGBHMS-001 Bedienungsanleitung
CONTENTS
#1: Description and features 3
#2: Powering the accessory 4
#3: Pairing the accessory 5
#4: Physical installation 6
#5: Reset 7
#6: Functionality 8
#7: Congurable parameters 9
#8: Specications 11
#9: Regulations 12
OPERATING
MANUAL EN
FIBARO MOTION SENSOR
FGBHMS-001
v1.1
2
Important safety information
Read this manual before attempting to install the device!
Failure to observe recommendations included in this manual
may be dangerous or cause a violation of the law. The manufacturer,
Fibar Group S.A. will not be held responsible for any loss or damage
resulting from not following the instructions of operating manual.
!
HomeKit technology
Apple HomeKit technology provides an easy, secure way to control
HomeKit-enabled accessories using Siri on your iPhone, iPad, or iPod
touch.
After installing your FIBARO Motion Sensor, congure it from a
compatible app with just a few simple steps.
You can even create your own custom scenes to control your home
settings. For example, you can create a scene to automatically turn
o the lights, lock your doors, close the garage door, and set the
thermostat to the desired temperature in just one step.
To control this HomeKit-enabled accessory, iOS 9.3.5 or later is
recommended.
Controlling this HomeKit-enabled accessory automatically and
away from home requires an Apple TV with tvOS 9.2 or later or
an iPad with iOS 9.3 or later set up as a home hub.
i
3
DESCRIPTION AND FEATURES
Main features of FIBARO Motion Sensor:
• compatible with Apple HomeKit technology
• Bluetooth® low energy technology for wireless communication
• detects motion using a passive IR sensor
• measures ambient temperature
• measures light intensity
• detects tampering using accelerometer
• easy installation
• may be installed anywhere - wall or any surface
• battery powered
• indicates state using multicolor LED diode
FIBARO Motion Sensor is a HomeKit-enabled multi-sensor using
Bluetooth® low energy technology.
Along with detecting motion, the accessory measures the ambient
temperature and light intensity.
The sensor has a built-in accelerometer to detect any tampering with
the accessory.
FIBARO Motion Sensor is battery powered and designed to be
installed quickly and easily on any surface.
The eye-shaped LED indicator signals motion, temperature level,
tampering and can be used to identify the accessory.
#1: Description and features
4
POWERING THE ACCESSORY
#2: Powering the accessory
1. Turn the cover counter-clockwise and open it.
2. Remove the battery blocker and check if the battery is placed cor-
rectly.
3. The accessory will glow red – it is ready to be paired.
4. Close the cover and turn it clockwise, dots on the casing should
align.
NOTE
Remember to use
only battery type
specied in the man-
ual and keep the right
polarity.
i
NOTE
If the accessory blinks
green after powering,
it is already paired and
has to be reset to pair
again.
i
5
PAIRING THE ACCESSORY
#3: Pairing the accessory
1. Open the Settings app on your iOS device.
2. Go to the Bluetooth® section, and turn the Bluetooth® on.
3. Place the accessory next to your iOS device.
4. Open a HomeKit compatible app of your choosing on your iOS
device.
5. Open pairing window in your HomeKit app to detect available
accessories.
6. Choose Motion Sensor you wish to pair.
7. You can identify it - Motion Sensor will triple blink blue 3 times.
8. Find HomeKit Setup Code on the last page of Quick Start Guide
included in the box that looks like this:
9. Start pairing with your HomeKit app.
10. Point your iOS device’s camera at the Setup Code to scan it or en-
ter the Setup Code manually.
11. If entered Setup Code is valid, the device will complete the setup
process.
12. Follow instructions displayed in the application.
XXX-XX-XXX
NOTE
Remember to keep
your HomeKit Setup
Code in safe place. You
may need it in case of
re-pairing.
i
6
PHYSICAL INSTALLATION
#4: Physical installation
Installing the Motion Sensor:
1. Install the holder (using an expansion bolt or a sticker).
2. Insert the device into the holder.
3. Test the operation - check whether the accessory indicates motion
detection.
Detection range:
Detection range of the Motion Sensor is shown below. Actual range
of the Sensor can be inuenced by environmental conditions.
0 m
5 m
5 m
7 m
Installation location and working conditions:
The Motion Sensor should be installed in a corner of the room or per-
pendicularly to the doors.
Moving objects such as trees blowing in the wind, cars passing by,
household fans and moving masses of air and heat within detection
area of the sensor can cause false motion detection.
Sticker
0 m
3 m
7 m
7
RESET
Resetting the Motion Sensor to factory defaults:
Reset procedure allows to restore the accessory back to its factory
settings including HomeKit pairing.
1. Open the cover.
2. Press and hold the button.
3. Wait for the LED indicator to glow yellow.
4. Release the button.
5. Click the button to conrm.
6. Accessory will glow red to conrm reset.
7. Delete the accessory from the app before pairing it again.
Button
#5: Reset
8
FUNCTIONALITY
#6: Functionality
Motion detection:
The Motion Sensor detects movement using PIR sensor and reports it
to your iOS device.
Blink of LED indicates detected motion. Color of blink is dependent on
current ambient temperature (smooth transition through blue, green
and red). Brightness of blink is adjusted by measured light intensity.
Tamper detection:
The Motion Sensor detects tampering when accessory is moved and
reports it to your iOS device. Tampering is indicated with an alternate
blinking in red, blue and white.
Temperature measuring:
The Motion Sensor measures ambient temperature every 5 min-
utes. If the measured temperature diers from previously reported
by at least 2°C (3.6°F), accessory reports it to your iOS device.
Battery level measuring:
The Motion Sensor measures battery level every 24 hours and reports
it to your iOS device. Additionally, if battery level is below 15%, the
accessory will report low level battery status to your iOS device.
Light intensity measuring:
The Motion Sensor measures light intensity. If the measured light in-
tensity diers from previously reported by at least 200 lux, accessory
reports it to your iOS device.
PIR sensor malfunction detection (Fault Code 1):
The Motion Sensor detects malfunction of PIR sensor (responsible for
motion detection) and reports it to your iOS device.
Getting Fault Code 1 warning means that the accessory is damaged
and should be returned to the distributor for the warranty (if still valid).
NOTE
The accessory mea-
sures light intensity
in the place of instal-
lation, not where the
sensor is pointed.
i
NOTE
The accessory mea-
sures temperature in
the place of installa-
tion. Remember that
temperature near
the ceiling may dier
from that on eye-level
or the oor.
i
9
CONFIGURABLE PARAMETERS
#7: Congurable parameters
1. Motion detection – sensor sensitivity
This parameter allows to set sensitivity of PIR sensor used for motion
detection.
The higher the value of this parameter, the higher the sensitivity.
Available settings: 1– low sensitivity
2– medium sensitivity
3– high sensitivity
Default setting: 2 (medium sensitivity)
2. Tamper – sensor sensitivity
This parameter allows to set sensitivity of tamper detection.
The higher the value of this parameter, the higher the sensitivity.
Available settings: 0– tamper disabled
1– low sensitivity
2– medium sensitivity
3– high sensitivity
Default setting: 2 (medium sensitivity)
3. Motion detection – LED indication
This parameter allows to choose how the LED indicator will behave
after detecting motion.
Available settings: 0– LED indications disabled
1– color dependent on temperature*
2– ashlight mode**
3– white, 4– red, 5– green, 6– blue, 7– yellow,
8– cyan, 9– magenta
Default setting: 1 (color dependent on temperature)
4. Tamper – LED indication
This parameter allows to choose if accessory will indicate tampering
using LED (alternate blinking in red, blue and white).
Available settings: 0– tamper indication disabled
1– tamper indication enabled
Default setting: 1 (tamper indication enabled)
10
CONFIGURABLE PARAMETERS
5. Motion detection - sustain time
This parameter allows to set how long the information about detect-
ed motion is sustained by the accessory. Each subsequent motion de-
tection causes time to be counted from the beginning.
Available settings: 1-32767 – sustain time in seconds
Default setting: 30 (30 seconds)
Andere Handbücher für FGBHMS-001
2
Inhaltsverzeichnis
Andere FIBARO Zubehör Handbücher
FIBARO
FIBARO FGFS-101-EN-A Bedienungsanleitung
FIBARO
FIBARO FGFS-101 Bedienungsanleitung
FIBARO
FIBARO Flood Sensor Bedienungsanleitung
FIBARO
FIBARO Flood Sensor Bedienungsanleitung
FIBARO
FIBARO FGWPA-111 Bedienungsanleitung
FIBARO
FIBARO FGFS-101 Bedienungsanleitung
FIBARO
FIBARO FGWPB-111 Bedienungsanleitung
FIBARO
FIBARO FGWOE-011 Bedienungsanleitung
FIBARO
FIBARO FGK-101 Bedienungsanleitung
FIBARO
FIBARO FGFS-101-ZW5 Bedienungsanleitung
FIBARO
FIBARO FGBHMS-001 Installationsanleitung
FIBARO
FIBARO FGBHFS-101 Bedienungsanleitung
FIBARO
FIBARO FGBHDW-002 Bedienungsanleitung
FIBARO
FIBARO FGBHCD-001 Bedienungsanleitung
FIBARO
FIBARO FGWPB-121 Bedienungsanleitung
FIBARO
FIBARO FGFS-001 Bedienungsanleitung
FIBARO
FIBARO FGMS-001 Bedienungsanleitung
FIBARO
FIBARO FGBHFS-101 Bedienungsanleitung
FIBARO
FIBARO FGBHFS-001 Bedienungsanleitung
FIBARO
FIBARO FGBHDW-002 Bedienungsanleitung
