FIBARO FGWOE-011 Bedienungsanleitung
FIBARO WALLI OUTLET
FGWOE-011 and FGWOF-011
OPERATING
MANUAL
EN
v1.0
3
Table of contents
1: Important safety information 4
2: Description and features 5
2.1: Description 5
2.2: Main features 5
3: Specications 6
4: Installation 7
4.1: Before installation 7
4.2: Preparing for installation 7
4.3: Electrical connection 8
4.4: First assembly 8
4.5: Changing covers 9
5: Adding to Z-Wave network 11
5.1: Adding manually 11
5.2: Adding using SmartStart 12
6: Removing from Z-Wave network 13
7: Operating the device 14
7.1: Controls 14
7.2: Button control 14
7.3: Visual indications 14
7.4: Menu 15
7.5: Resetting to factory defaults 15
8: Power and energy metering 16
9: Z-Wave range test 17
10: Conguration 18
10.1: Associations 18
10.2: Advanced parameters 18
11: Z-Wave specication 27
12: Parts compatibility 29
13: Regulations 31
4
IMPORTANT SAFETY INFORMATION
1: Important safety information
Read this manual before attempting to install the device!
!Failure to observe recommendations included in this manual
may be dangerous or cause a violation of the law. The manu-
facturer, Fibar Group S.A. will not be held responsible for any loss or
damage resulting from not following the instructions of operating
manual.
DANGER OF ELECTROCUTION!
The device is designed to operate in electrical home installa-
tion. Faulty connection or use may result in re or electric
shock.
All works on the device may be performed only by a qualied
and licensed electrician. Observe national regulations.
Even when the device is turned o, voltage may be present at
its terminals. Any maintenance introducing changes into the
conguration of connections or the load must be always performed
with disabled fuse.
To avoid risk of electrical shock, do not operate the device with
wet or moist hands.
Do not modify!
!Do not modify this device in any way not included in this
manual.
Other devices
!The manufacturer, Fibar Group S.A. will not be held responsi-
ble for any damage or loss of warranty privileges for other con-
nected devices if the connection is not compliant with their
manuals.
This product is intended for indoor use only in dry locations.
!Do not use in damp or wet locations, near a bathtub, sink,
shower, swimming pool, or anywhere else where water or
moisture are present.
Not a toy!
!This product is not a toy. Keep away from children and
animals!
5
DESCRIPTION ANDFEATURES
2: Description and features
2.1: Description
FIBARO Walli Outlet is a smart electrical outlet designed to control
electrical devices via Z-Wave network.
It measures active power and energy consumed by the controlled
load.
You can install it with provided cover plate and socket cover or other
compatible.
2.2: Main features
• Can turn ON/OFF plugged device remotely.
• Available in two versions for plug types:
»Type E,
»Type F.
• Can be used with FIBARO Walli covers or other compatible (see
“Parts compatibility” on page 29):
»GIRA – System 55 (Standard 55, E2, Event, Event Clear),
»Legrand – Céliane,
»Schneider – Odace.
• Active power and energy consumption metering.
• Displays current load using multicolour LED frame (with FIBARO
cover plate).
• Supports Z-Wave network Security Modes: S0 with AES-128 en-
cryption and S2 Authenticated with PRNG-based encryption.
• Works as a Z-Wave signal repeater (all non-battery operated de-
vices within the network will act as repeaters to increase reliabili-
ty of the network).
• May be used with all devices certied with the Z-Wave Plus cer-
ticate and should be compatible with such devices produced by
other manufacturers.
i
The device is a Security Enabled Z-Wave Plus product
and a Security Enabled Z-Wave Controller must be
used in order to fully utilize the product.
6
SPECIFICATIONS
3: Specications
Power supply 110-230V~ 50/60 Hz
Rated load current 16A – resistive loads
Active element micro-gap relay μ
Recommended external
overcurrent protection
16A type B circuit breaker
For installation in boxes Ø = 60mm, depth ≥ 50mm
Recommended wires cross-section area between 1.5-4.0mm2,
stripped 15.5-16.5mm of insulation
Operating temperature 0–40°C
Ambient humidity 0–90% RH without condensation
Radio protocol Z-Wave (500 series chip)
Radio frequency band 868.0–868.6MHz; 869.7–870.0MHz
Max. transmitting power +6dBm
Range up to 50m outdoors
up to 40m indoors
(depending on terrain and building
structure)
Dimensions
(Height x Width x Depth)
FGWOE-011: 86 x 86 x 48 mm
FGWOF-011: 86 x 86 x 51 mm
Compliance with EU
directives
RoHS 2011/65/EU
RED 2014/53/EU
i
Radio frequency of individual device must be same as
your Z-Wave controller. Check information on the box
or consult your dealer if you are not sure.
7
INSTALLATION
4: Installation
4.1: Before installation
!Connecting the device in a manner inconsistent with this
manual may cause risk to health, life or material damage.
• Do not power the device before fully assembling it in the mount-
ing box,
• Connect only in accordance to the diagram,
• Install only in ush mounting boxes compliant with a relevant na-
tional safety standards and with depth no less than 50mm,
• Do not connect devices which are not compliant with the speci-
cation or relevant safety standards.
• Make sure you have all required parts when installing with covers
other than FIBARO (see “Parts compatibility” on page 29).
Device parts:
1
2
3
4
5
1 – screw, 2 – socket cover, 3 – cover plate, 4 – unit (device), 5 – mount-
ing frame
4.2: Preparing for installation
1. Remove the screw.
2. Take o the socket cover and cover plate.
3. Prepare wires by removing 15.5-16.5mm of insulation from their
ends. Groove on the back of the unit shows maximum wire length.
8
INSTALLATION
4.3: Electrical connection
1. Switch o the mains voltage (disable the fuse).
2. Connect the device according to the diagram:
PE
N
L
Notes for the diagram:
N – terminal for neutral wire
– terminal for earthing wire
L – terminal for live wire
Diagram: Example connection in electrical installation
3. Verify correctness of connection.
4. Tighten the terminal screws using PH1 screwdriver.
4.4: First assembly
When installing with FIBARO covers:
1. Insert the device with mounting frame into the mounting box and
secure with mounting claws and screws.
2. Snap the cover plate to the device.
3. Snap the socket cover to the device.
4. Secure with a screw.
5. Add the device to Z-Wave network (see “Adding to Z-Wave
network” on page 11)
9
INSTALLATION
4.5: Changing covers
!For safety reasons the button should be used only
with FIBARO cover. We recommend adding the device
to Z-Wave network before changing the cover plate.
i
When installing with covers other than FIBARO, we
recommend disabling the LED by changing parameter
13 to 0.
When installing with GIRA covers:
1. Switch o the mains voltage (disable the fuse).
2. Dismount the socket cover and cover plate.
3. Dismount shutter mechanism using pliers.
4. Snap the new cover plate to the device.
5. Snap the new socket cover to the device.
6. Secure with a screw.
7. Switch on the mains voltage.
When installing with Legrand covers:
1. Switch o the mains voltage (disable the fuse).
2. Dismount the socket cover and cover plate.
3. Take the device out of the mounting box and detach the wires.
10
INSTALLATION
4. Replace FIBARO mounting frame with Legrand mounting frame
(FG-Wx-AS-4002).
5. Connect wires according to “Electrical connection” on page 8.
6. Insert the device with mounting frame into the mounting box and
secure with mounting claws and screws.
7. Snap the new cover plate to the device.
8. Snap the new socket cover to the device.
9. Switch on the mains voltage.
When installing with Schneider covers:
1. Switch o the mains voltage (disable the fuse).
2. Dismount the socket cover and cover plate.
3. Take the device out of the mounting box and detach the wires.
4. Replace FIBARO mounting frame with Schneider mounting frame
(FG-Wx-AS-4003).
5. Connect wires according to “Electrical connection” on page 8.
6. Insert the device with mounting frame into the mounting box and
secure with mounting claws and screws.
7. Snap the new cover plate to the device.
8. Snap the new socket cover to the device.
9. Switch on the mains voltage.
Andere Handbücher für FGWOE-011
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere FIBARO Zubehör Handbücher
FIBARO
FIBARO FGWPB-111 Bedienungsanleitung
FIBARO
FIBARO FGBHDW-002 Bedienungsanleitung
FIBARO
FIBARO FGK-10x Bedienungsanleitung
FIBARO
FIBARO FGBHFS-001 Bedienungsanleitung
FIBARO
FIBARO FGFS-101 Bedienungsanleitung
FIBARO
FIBARO FGMS-001-USA-A-V1.01 Bedienungsanleitung
FIBARO
FIBARO Flood Sensor Bedienungsanleitung
FIBARO
FIBARO FGK-101 Bedienungsanleitung
FIBARO
FIBARO FGFS-101 Bedienungsanleitung
FIBARO
FIBARO FGWPA-111 Bedienungsanleitung
FIBARO
FIBARO FGSS-001-EN-A-v1.00 Bedienungsanleitung
FIBARO
FIBARO FGFS-101 Bedienungsanleitung
FIBARO
FIBARO FGBHMS-001 Installationsanleitung
FIBARO
FIBARO FGBHDW-002 Bedienungsanleitung
FIBARO
FIBARO FGBHCD-001 Bedienungsanleitung
FIBARO
FIBARO FGDW-002 Bedienungsanleitung
FIBARO
FIBARO FGWPG-111 Bedienungsanleitung
FIBARO
FIBARO FGWPG-111 Bedienungsanleitung
FIBARO
FIBARO FGBHDW-002 Bedienungsanleitung
FIBARO
FIBARO FGWPB-121 Bedienungsanleitung
