FIBARO FGDW-002 Bedienungsanleitung

FIBARO DOOR/WINDOW SENSOR 2

FGDW-002

CONTENTS

#1: Description and features 3

#2: Basic activation 4

#3: Adding/removing the device 5

#4: Physical installation 6

#5: Operating the device 7

#6: Association 9

#7: Advanced parameters 10

#8: Specications 14

#9: Regulations 15

OPERATING

MANUAL EN

v1.0

Important safety information

Read this manual before attempting to install the device!

Failure to observe recommendations included in this manual

may be dangerous or cause a violation of the law. The manufacturer,

Fibar Group S.A. will not be held responsible for any loss or damage

resulting from not following the instructions of operating manual.

The alarm functionality of devices is an additional feature increasing

the comfort level of your home automation system. If you want to

use professional security service, please contact them to determine

what systems can provide a protection of your estate.

Compliance with safety standards:

The device is designed to be used in Z-wave home automation sys-

tems (e.g. FIBARO) and is complaint with IEC/UL/CSA 60950-1. In case

of the integration with another system, e.g. alarm system, it is re-

quired to verify the compliance with additional standards.

General information about

the FIBARO System

FIBARO is a wireless smart home automation system, based on the

Z-Wave protocol. All of available devices can be controlled through

a computer (PC or Mac), smartphone or tablet. Z-Wave devices are

not only receivers, but can also repeat the signal, increasing the

Z-Wave network’s range. It gives advantage over traditional wireless

systems that require direct link between transmitter and receiver, as

a result the construction of the building could aect network’s range

negatively.

Every Z-Wave network has its unique identication number (home

ID). Multiple independent networks can exist in the building without

interfering. Transmission security of FIBARO System is comparable to

wired systems.

Z-Wave technology is the leading solution in smart home automation.

There is a wide range of Z-Wave devices that are mutually

compatible, independently of manufacturer. It gives the system the

ability to evolve and expand over time. For more information visit

www.baro.com.

DESCRIPTION AND FEATURES

Main features of FIBARO Door/Window Sensor 2:

• Compatible with any Z-Wave or Z-Wave+ Controller,

• Supports protected mode (Z-Wave network Security Mode) with

AES-128 encryption,

• Door/window opening detected through separation of Sensor’s

body and a magnet,

• Built-in temperature sensor,

• Detects tampering, when detached or opened,

• Easily mounted on doors, windows, garage gates and roller blinds,

• Battery powered,

• Visual LED indicator signalling status of the device,

• 7 color variations.

FIBARO Door/Window Sensor 2 is a wireless, battery powered Hall

eect contact sensor, compatible with the Z-Wave Plus standard.

Changing the device’s status will automatically send signal to the

Z-Wave controller and associated devices.

Sensor can be used to trigger scenes and wherever there is a need

for information about opening or closing of doors, windows, garage

doors, etc. Opening is detected by separating the sensor’s body and

the magnet.

In addition the FIBARO Door/Window Sensor 2 is equipped with

a built-in temperature sensor.

#1: Description and features

FIBARO Door/Window Sensor 2

is a fully compatible Z-Wave

PLUS device.

NOTE

This device may be

used with all devices

certied with Z-Wave

Plus certicate and

should be compatible

with such devices pro-

duced by other manu-

facturers.

NOTE

Z-Wave Controller

must support Z-Wave

Security Mode in

order to fully utilize the

product.

BASIC ACTIVATION

#2: Basic activation

1. Take o the cover.

2. Remove the battery blocker.

3. Close the cover.

4. Add the device (see “Adding/removing the device”on page 5).

5. Install the device (see “Physical installation” on page 6).

ADDING/REMOVING THE DEVICE

#3: Adding/removing the device

Adding (Inclusion) - Z-Wave device learning mode, allowing to add

the device to existing Z-Wave network.

To add the device to the Z-Wave network:

1. Close the cover.

2. Place the Door/Window Sensor 2 within the direct range of your

Z-Wave controller.

3. Set the main controller in (Security/non-Security Mode) add mode

(see the controller’s manual).

4. Quickly, three times press one of the TMP buttons (while the other

button is pressed).

5. Wait for the adding process to end.

6. Successful adding will be conrmed by the Z-Wave controller’s

message.

Removing (Exclusion) - Z-Wave device learning mode, allowing to

remove the device from existing Z-Wave network.

To remove the device from the Z-Wave network:

1. Close the cover.

2. Place the Door/Window Sensor 2 within the direct range of your

Z-Wave controller.

3. Set the main controller into remove mode (see the controller’s

manual).

4. Quickly, three times press one of the TMP buttons (while the other

button is pressed).

5. Wait for the removing process to end.

6. Successful removing will be conrmed by the Z-Wave controller’s

message.

NOTE

Adding in Security

Mode must be per-

formed up to 2 meters

from the controller.

NOTE

In case of problems

with adding the de-

vice, please reset the

device and repeat the

adding procedure.

TMP

button

TMP

button

PHYSICAL INSTALLATION

#4: Physical installation

To install the Door/Window Sensor:

1. Peel o the protective layer from the sticker on the device.

2. Stick the device onto the door/window frame.

3. Peel o the protective layer from the sticker on the magnet.

4. Stick the magnet onto the moving part of the door/window, no

further than 5mm from the sensor.

Correct positioning of the magnet in relation to the Sensor:

(vertical line marks should align)

Positioning of the Sensor and the magnet:

max. 5 mm

OPERATING THE DEVICE

#5: Operating the device

Tamper (TMP) button:

The Door/Window Sensor 2 is equipped with a tamper switch with

two buttons.

First TMP button is located inside the device, pressed by the closed

cover and is used to detect openning it.

Second TMP button is located at bottom of the device, pressed by the

surface on which the device is mounted and is used to detect detach-

ing the device.

For the tamper switch to work one of the buttons must always be

pressed!

When one of the buttons is released, the tamper alarm will be send to

the controller and associated devices.

Additionally, tamper button allows to control the device directly.

TMP

button

TMP

button

Waking up the Door/Window Sensor 2:

The Door/Window Sensor 2 needs to be woken up to receive informa-

tion about the new conguration from the controller, like parameters

and associations.

To wake up the sensor manually, click one of the TMP buttons (while

the other button is pressed).

Controlling the Door/Window Sensor 2 with FIBARO Home Center

controller:

After adding the Sensor to the FIBARO System, it will be represented

by two or three icons in Home Center interface.

First icon informs about the status of magnetic sensor (open/close),

second icon displays temperature measured by the built-in sensor.

Third icon is assigned to high/low temperature alarm and is visible only

if parameter 54 is not equal to 0.

OPERATING THE DEVICE

Resetting the Door/Window Sensor 2:

Reset procedure allows to restore the device back to its factory set-

tings, which means all information about the Z-Wave controller and

user conguration will be deleted.

In order to reset the device:

1. Open the cover.

2. Remove the battery.

3. Install the battery while holding both TMP buttons.

4. Release the TMP button within 5 seconds.

5. Visual indicator will blink 3 times to conrm launching of reset

procedure.

6. Wait around 30s for the resetting process to end, do not remove

the battery.

7. Visual LED indicator will blink 6 times to conrm the reset.

NOTE

Resetting the device is

not the recommend-

ed way of removing

the device from the

Z-Wave network. Use

reset procedure only

if the primary con-

troller is missing or

inoperable. Certain

device removal can be

achieved by the pro-

cedure of removing

described in “Adding/

removing the device”

on page 5.

Replacing the battery:

In FIBARO Home Center controller current battery level is displayed

in the interface. If a battery icon turns red, it means the battery needs

replacement.

NOTE

Opening the casing

may result in trigger-

ing an alarm. To avoid

it, remove the asso-

ciations for the 3rd

group.

Notication report:

The device uses Notication Command Class to report dierent

events.

Notication Type Triggering Event

Home Security Tampering, product covering

removed

Access Control Door/window opened

Access Control Door/window closed

Power Management Replace battery now

Heat Alarm Overheat detected, unknown

location

Heat Alarm Underheat detected, unknown

location

ASSOCIATION

#6: Association

The Door/Window Sensor 2 provides the association of three

groups:

1st Association Group – “Lifeline” reports the device status and al-

lows for assigning single device only (main controller by default).

2nd Association Group – “On/O” is assigned to the device status -

Hall eect sensor (sends Basic Set command frames).

3rd Association Group – “Tamper” is assigned to the TMP switch

(sends alarm command frames).

To add an association (using the Home Center controller):

1. Go to device options by clicking the icon:

2. Select the„Advanced” tab.

3. Specify to which group and what devices are to be associated.

4. Save the changes.

5. Wake up the device manually or wait for the next automatic wake

up.

NOTE

Association allows

transfer of control

commands between

devices without par-

ticipation of the main

controller.

Direct range between

devices is recom-

mended.

The Door/Window Sensor 2 in 2nd and 3rd group allows to control

5 devices (regular or multichannel) per an association group.

“LifeLine” group is reserved solely for the controller and hence only 1

node can be assigned.

Association (linking devices) - direct control of other devices within

the Z-Wave system network e.g. Dimmer, Relay Switch, Roller Shutter

or scene (may be controlled only through a Z-Wave controller).

ADVANCED PARAMETERS

#7: Advanced parameters

The Door/Window Sensor 2 allows to customize its operation to user’s

needs. Settings are available in the FIBARO interface as simple op-

tions that may be chosen by selecting the appropriate box.

In order to congure the Door/Window Sensor 2 (using

the Home Center controller):

1. Go to the device options by clicking the icon:

2. Select the„Advanced” tab.

1. Door/window state

This parameter allows to set in what state is door/window when the

magnet is close to the sensor.

Available settings: 0- closed when magnet near

1- opened when magnet near

Default setting: 0Parameter size: 1[byte]

2. Visual LED indications

This parameter denes events indicated by the visual LED indicator.

Disabling events might extend battery life.

Available settings: 1- indication of opening/closing status change

2- indication of wake up (1 x click or periodical)

4- indication of device tampering

Default setting: 6Parameter size: 1[byte]

Wake up interval

Available settings: 0or 3600-64800 (in seconds (1-18h), 3600s (1h)

step)

Default setting: 21600 (6h)

The Door/Window Sensor will wake up after each dened time inter-

val and always try to connect with the main controller. After a suc-

cessful communication attempt, the sensor will update conguration

parameters, associations and settings and will go into standby mode.

After failed communication attempt (e.g. lack of Z-Wave range) the

device will go into standby mode and retry to establish connection

with the main controller after the next time interval.

Setting wake up interval to 0 disables sending Wake Up Notication

frame automatically. Wake up may be still performed manually by a

clicking one of the TMP buttons (while the other button is pressed).

Longer time interval means less frequent communication and thus a

longer battery life.

NOTE

Entering invalid value

of parameter will re-

sult in response with

Application Rejected

frame and not setting

the value.

NOTE

Parameter 2 values

may be combined, e.g.

1+2=3 means that in-

dications for opening/

closing and waking up

are enabled.

Andere Handbücher für FGDW-002

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere FIBARO Zubehör Handbücher

FIBARO

FIBARO FGBHDW-002 Bedienungsanleitung

FIBARO

FIBARO FGWP-102 Bedienungsanleitung

FIBARO

FIBARO FGFS-101 Bedienungsanleitung

FIBARO

FIBARO FGFS-101 Bedienungsanleitung

FIBARO

FIBARO FGWPG-111 Bedienungsanleitung

FIBARO

FIBARO FGBHDW-002 Bedienungsanleitung

FIBARO

FIBARO FGFS-101 Bedienungsanleitung

FIBARO

FIBARO FIBEFGMS-001-ZW5 Bedienungsanleitung

FIBARO

FIBARO FGMS-001 Bedienungsanleitung

FIBARO

FIBARO FGBHFS-101 Bedienungsanleitung

FIBARO

FIBARO FGWPB-121 Bedienungsanleitung

FIBARO

FIBARO FGBHMS-001 Bedienungsanleitung

FIBARO

FIBARO FGBHFS-101 Bedienungsanleitung

FIBARO

FIBARO FGWPA-111 Bedienungsanleitung

FIBARO

FIBARO FGMS-001-USA-A-V1.01 Bedienungsanleitung

FIBARO

FIBARO FGBHFS-001 Bedienungsanleitung

FIBARO

FIBARO CO Sensor FGCD-001 Bedienungsanleitung

FIBARO

FIBARO FGSS-001-EN-A-v1.00 Bedienungsanleitung

FIBARO

FIBARO FGK-101 Bedienungsanleitung

FIBARO

FIBARO FGWOE-011 Bedienungsanleitung

FIBARO

FIBARO FGFS-101-EN-A Bedienungsanleitung

FIBARO

FIBARO FGMS-001 Bedienungsanleitung

FIBARO

FIBARO FGK-10x Bedienungsanleitung

FIBARO

FIBARO FGFS-101 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung