Flexbar 6.3:1 Bedienungsanleitung



Flexbar 6.3:1

ZOOM STEREO MICROSCOPE

MANUAL



250 Gibbs Road, Islandia, NY 11749 • 631-582-8440 (P) • 631-582-8487 (F)

www.flexbar.com • sales@flexbar.com

6.3:1 ZOOM MICROSCOPE

250 Gibbs Road, Islandia, NY 11749 • 631-582-8440 • www.flexbar.com 2

CONTENTS

SAFETY NOTES .................................................................................................................. 3

CARE AND MAINTENANCE ................................................................................................ 3

INTRODUCTION .................................................................................................................. 4

UNPACKING AND COMPONENTS ..................................................................................... 4

COMPONENTS DIAGRAM .................................................................................................. 4

ASSEMBLY .......................................................................................................................... 5

DETAILED ASSEMBLY PROCEDURE ................................................................................ 6

ADJUSMENT AND OPERATION

ADJUSTING BINOCULAR VIEWING HEAD................................................................... 8

FOCUS ADJUSTMENT................................................................................................... 9

SPECIFICATIONS.............................................................................................................. 10

TROUBLESHOOTING........................................................................................................ 11

MAINTENANCE.................................................................................................................. 12

SERVICE............................................................................................................................ 12

WARRANTY ....................................................................................................................... 12

6.3:1 ZOOM MICROSCOPE

250 Gibbs Road, Islandia, NY 11749 • 631-582-8440 • www.flexbar.com 3

SAFETY NOTES

1. Open the shipping carton carefully to prevent any accessory, i.e. objectives or eyepieces, from

dropping and being damaged.

2. Keep the instrument out of direct sunlight, high temperature or humidity, and dusty environments.

3. If any specimen solutions or other liquids splash onto the stage, objective or any other component,

disconnect the power cord immediately and wipe up the spillage. Otherwise, the instrument may be

damaged.

4. LAMP REPLACEMENT -- CAUTION: the glass envelope of the lamp may be extremely

hot. DO NOT attempt to change the lamp before it is completely cooled or without

wearing adequate skin protection.

5. All electrical connectors (power cord) should be inserted into an electrical surge protector to prevent

damage due to voltage fluctuations.

6. FUSE REPLACEMENT -- For safety when replacing the fuse (ONLY replace with the

same size, type and rating of original fuse), be sure the main switch is in the off position,

disconnect the power cord from outlet, and replace the fuse. Reconnect the power cord

and turn unit on.

7. Confirm that the input voltage indicated on your microscope corresponds to your line voltage. The

use of a different input voltage other than indicated will cause severe damage to the microscope.

NOTE: Always plug the stereomicroscope power cord into a suitable grounded electrical outlet. A

grounded 3-wire cord is provided.

CARE AND MAINTENANCE

1. Do not attempt to disassemble any component including eyepieces, objectives or focusing assembly.

2. Keep the instrument clean; remove dirt and debris regularly. Accumulated dirt on metal surfaces

should be cleaned with a damp cloth. More persistent dirt should be removed using a mild soap

solution. Do not use organic solvents for cleansing.

3. The outer surface of the optics should be inspected and cleaned periodically using an air stream from

an air bulb. If dirt remains on the optical surface, use a soft, lint free cloth or cotton swab dampened

with a lens cleaning solution (available at camera stores). All optical lenses should be swabbed using

a circular motion. A small amount of absorbent cotton wound on the end of a tapered stick makes a

useful tool for cleaning recessed optical surfaces. Avoid using an excessive amount of solvents as

this may cause problems with optical coatings or cemented optics or the flowing solvent may pick up

grease making cleaning more difficult.

4. Store the instrument in a cool, dry environment. Cover the microscope with the dust cover when not

in use.

5. Flexbar microscopes are precision instruments which require periodic servicing to maintain

proper performance and to compensate for normal wear. A regular schedule of preventative

maintenance by qualified personnel is highly recommended. Your authorized Flexbardistributor

can arrange for this service.

6.3:1 ZOOM MICROSCOPE

250 Gibbs Road, Islandia, NY 11749 • 631-582-8440 • www.flexbar.com 4

INTRODUCTION

Congratulations on the purchase of your new Flexbar microscope. Flexbar microscopes are

engineered and manufactured to the highest quality standards. Your microscope will last a lifetime if

used and maintained properly. Flexbar microscopes are carefully assembled, inspected and tested

by our staff of trained technicians in our New York facility. Careful quality control procedures ensure each

microscope is of the highest quality prior to shipment.

UNPACKING AND COMPONENTS

Your microscope arrived packed in a molded shipping carton. Do not discard the carton: the shipping

carton should be retained for reshipment of your microscope if needed. Avoid placing the microscope in

dusty surroundings or in high temperature or humid areas as mold and mildew can form. Carefully

remove the microscope from the shipping carton and place the microscope on a flat, vibration-free

surface.

COMPONENTS DIAGRAM

NOTE: Stand ordered may not be as pictured above.

Binocular Head

Stand

Focusing Knob

Power Cord

Shift Knob

Switch

Base

Eyepieces

Lock-screw

Stage Plate

6.3:1 ZOOM MICROSCOPE

250 Gibbs Road, Islandia, NY 11749 • 631-582-8440 • www.flexbar.com 5

ASSEMBLY

The diagram below shows how to assemble the various modules. The numbers indicate the order of

assembly.

When assembling the microscope, make sure that all parts are free of dust and dirt, and avoid scratching

any parts or touching glass surfaces.

Eyepieces

Binocular Head

Power Cord

Stand

Lock-screw

6.3:1 ZOOM MICROSCOPE

250 Gibbs Road,Islandia, NY 11749 • 631-582-8440 • www.flexbar.com 6

DETAILED ASSEMBLY PROCEDURE

Mounting the Binocular Head (Fig. 1)

Loosen the clamping knob ③on the focus

mount ④and insert the binocular head and

zoom body assembly ② into the bracket of the

focus mount, then tighten the lock screw ③.

Mounting the Eyepieces (Fig. 1, Fig. 2, Fig. 3)

Remove the eyepiece dust caps ①(Fig. 1) and

gently insert the two adjustable eyepieces ⑤

(Fig. 2) into the eyepiece sleeves until they stop,

as shown in Fig.3. Replace the dust caps when

not in use.

IMPORTANT

ENVIRONMENT REQUIREMENTS

1 Ambient temperature: 0°C to 40°C (32°F

to 104°F)，Maximum R.H：85%。

2 High temperature will result in moisture

and mildew and could damage instrument.

3 Avoid placing the instrument in a dusty

environment. When not in use, cover the

microscope with the dust cover.

4 Keep the microscope on a flat and stable

surface.

Fig. 1

Fig. 2

Fig. 3

6.3:1 ZOOM MICROSCOPE

250 Gibbs Road, Islandia, NY 11749 • 631-582-8440 • www.flexbar.com 7

For Microscopes Purchased

With Illuminated Stands

VOLTAGE CHECK

Confirm that the input voltage indicated on the

rear label of the microscope corresponds to your

line voltage. The use of a different input voltage

than indicated will cause severe damage to your

microscope.

Connecting the Power Cord (Fig. 4)

Turn the power switch ⑥to the off position (O)

before connecting the power cord ⑦.

Insert the power cord plug ⑦into the power jack

of the microscope; make sure the connection is

snug.

Plug the power cord ⑧into the power supply

receptacle.

Using the Glass Stage (Fig. 5)

Set the glass stage plate ⑨on the center of the

base, and secure the slide with the two clips ⑩.

Fig. 4

Fig. 5

Fig. 6

6.3:1 ZOOM MICROSCOPE

250 Gibbs Road,Islandia, NY 11749 • 631-582-8440 • www.flexbar.com 8

ADJUSTMENT

AND OPERATION

Adjusting Binocular Viewing Head

Adjusting Interpupillary Distance (Fig. 6)

Different users have different interpupillary

distances (this distance is between the centers

of the pupils of each eye). When the operator

changes, it will be necessary to adjust the

interpupillary distance.

While looking through the eyepieces, hold the

left and right eyetubes of the viewing head and

adjust the eyetubes by opening or closing them

until the left and right fields of view coincide

completely and you are able to see a complete

circle.

Adjusting Diopter Ring (Fig. 7)

Set the dioptor rings ② of both eyepieces to “0”

position. (Do this when users change, because

different users will have different diopter

settings.)

Place an easy-to-observe specimen on the

stage plate, i.e., a coin.

Rotate the zoom knob ③ to the highest

magnification 5x, then turn the focusing knob ④

to focus the specimen.

Rotate the zoom knob ③ to the lowest

magnification 0.8x, looking only into the left

eyepiece, adjust the diopter ring on left eyepiece

to focus the specimen. Then repeat procedure

for the right eyepiece.

NOTE: The working distance (the distance

between the microscope objective to the top of

the specimen) of the microscope is 115mm, the

binocular head bracket ⑤ can be mounted onto

higher or lower positions according to your

needs by removing the clamping bolt with the

Allen wrench provided.

Fig. 6

Fig. 7

6.3:1 ZOOM MICROSCOPE

250 Gibbs Road, Islandia, NY 11749 • 631-582-8440 • www.flexbar.com 9

Focus Adjustment

Adjusting the Rotation Tension of the

Focus Adjustment Knob (Fig. 8, Fig. 9)

To adjust tension, hold both left and right focus

adjustment knobs ① with both hands, hold the

left knob (to prevent it from turning), and rotate

the right knob clockwise to increase (tighten) or

counterclockwise to decrease (loosen) the focus

knob tension.

After tension adjustment has been completed,

always rotate both adjustment knobs in the

same direction.

Changing the Magnification

The zooming knobs located on both sides of the

zooming body will change the magnification of

the specimen image.

Total Magnification = Magnification of zoom

body x magnification of eyepiece

(i.e., 0.8 x 10=8x)

NOTE: If using any of the optional auxiliary

objectives, then the above magnification would

be multiplied by auxiliary objective magnification.

(i.e., auxiliary 0.5 x 8=4x)

Moving the Microscope (Fig. 10)

Before moving the microscope, be sure to

remove any slide/samples. When moving the

microscope, hold the stand and base as shown

in Fig. 10 to keep it level.

Fig. 8

Fig. 9

Fig. 10

6.3:1 ZOOM MICROSCOPE

250 Gibbs Road, Islandia, NY 11749 • 631-582-8440 • www.flexbar.com 10

SPECIFICATIONS

Zoom ratio: 6/1 to 1

Objective magnification: 0.8x～5.0x

Eyepiece: Φ22 10x Wide Field, interpulpillary adjustable

Binocular viewing head: Inclined at 45 degrees, interpupillary distance range: 52～75mm

Working distance: 115mm

Range of movement: 105mm

Illumination system: LED lamp illumination

Input: 100-240V～, 0.15A, 50.60HZ

Auxiliary

Objective

Working

Distance

(mm)

Eyepiece

WF10X/22 WF15X/16 WF20X/12.5

Total

Magnification

Visual Field

(mm)

Total

Magnification

Visual Field

(mm)

Total

Magnification

Visual Field

(mm)

115 8-50X 27.5-4.4 12-75X 20.0-3.2 16-100X 15.6-2.5

0.5X 211 4-25X 55.0-8.8 6-37.5X 40.0-6.4 8-50X 31.2-5.0

2X 43.5 16-100X 13.8-2.2 24-150X 10.0-1.6 32-200X 7.8-1.3

Inhaltsverzeichnis

Andere flexbar Mikroskop Handbücher

flexbar

flexbar Z10 Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Olympus

Olympus SZ61 Bedienungsanleitung

flexbar 6.3:1 Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken