Formax FD 8400HS Bedienungsanleitung

High Security Paper Shredder

FD 8400HS Cross-Cut / Level 6

OPERATOR MANUAL

FIRST EDITION

10/08

Safety Devices and Other Features

Formax 8000 Series Shredders are equipped with various safety features:

Automatic Reverse Rotation

(Process takes about 6 to 8 seconds)

When too much paper is inserted, the cutter stops operating

and

automatically rotates in reverse to discharge the jammed paper. An

alarm sounds. Reduce the amount of paper and restart the operation.

Door Switch

If the door is open, the shredder will not operate.

Automatic Stop

When the shredded paper ﬁ lls the waste bin, the “FULL”

light comes

on and the cutter stops operation. Open the door, remove the waste

bin and empty paper shreds. Replace the waste bin, close the door

and continue operation.

Automatic Power Shut-Off

• If the shredder operates continuously for more than 30

minutes,

the power is automatically shut off.

• If the motor is overloaded, the “STOP” LED will ﬂ ash until it cools

down. When the ﬂ ashing stops the shredder is ready to be used

again.

Oil Indicator

Oil regularly for peak performance

NOTE:

High Security shredders require

a specialized oil that can only be ordered through Formax, part # 8000-15

The

“MANUAL” LED will ﬂ ash after every four (4) hours of operation as an indicator to oil

the shredder cutting blades. The LED will continue to ﬂ ash until oiled. NOTE: the

shedder will still operate when the LED is ﬂ ashing but at a decreased load capacity.

To oil:

Spread shredder oil onto the cutters through the feed opening, and allow the

oil to sit for a few minutes to permeate the cutting blades, then press the “REV” button

and hold for ﬁ ve seconds. “MANUAL” and “REV” LED indicators on control panel will

light. The shredder will operate in reverse for one minute, then the “AUTO” LED will

light indicating the shredder is ready.

Maintenance

• Disconnect power by pulling power cord plug from wall outlet.

• To clean the exterior, wipe the surface with a soft cloth. If the surface is

very dirty,

use a neutral detergent, then wipe again with a soft cloth.

CAUTION:

• Never put water directly on the surface of the shredder.

• Never clean the case with benzene or thinner, since it will cause discoloration.

• Do not dismantle the shredder. Contact your Formax Dealer for service.

NSA Approved

Meets the requirements of NSA/CSS speciﬁ cation for

Level 6 High-Security cross-cut shredders.

Operation

1. Open the door and ﬂ ip the breaker switch to the “ON”

position. Close door. Press the Power Switch on the right side

of the shredder to the “ON” position (This switch should be used

to turn the power on and off).

Auto Start/Auto Stop

When the “START” button is pushed, the signal lamp “AUTO”

will light. Insert paper to shred. The shredder will start and stop

automatically when using this function.

Manual Operation

If paper is too small for the shredder’s sensors to detect, shred

it manually. Push the “START” button once more and the

“MANUAL” lamp will light. Insert paper to be shredded. Three

minutes after shredding, the cutter automatically stops rotating.

Safety Precautions

To avoid personal injury, and damage to the shredder, observe the following safety

precautions. Please keep these instructions for future reference.

Set-up Guidelines

1. Install the shredder on a level surface, away from heat sources and direct sunlight.

2. Insert plug into wall outlet with the appropriate voltage, 110V. If the outlet is shared

with another electronic device, the total current should not exceed 30A (at 110V).

Speciﬁ cations

Cutting Style:

Cross Cut

Shred Size:

1/32” x 3/16” (Level 6)

Sheet Capacity:

6 to 7 (

NO staples or paper clips

)

Speed:

23 feet per minute

Feed Opening:

10.25”

Dimensions:

22” W x 20” D x 34” H

Bin Capacity:

20 gal.

Weight:

176 lbs.

Power supply:

110-120V, 60Hz

FD 8400HS - For paper only

Reverse Operation

Push the “REV” button and the signal lamp “REV” will light and cutters will operate in

reverse. If too much paper is inserted at one time in standard modes, the shredder

will automatically operate in reverse. If this occurs, remove the inserted paper and

shred in smaller amounts. NOTE: The maximum amount of paper to be shredded

differs according to paper quality, humidity and voltage. If the shredder is to be used

continuously, do not insert more than half of the maximum capacity.

Full Sensor

If the waste bin is full, the “FULL” lamp will light and the cutter will stop automatically.

Open the door, empty the waste bin of paper shreds, replace the waste bin, close

door, and continue to shred.

NOTE:

In case of emergency, push the

“Power Switch” to cut off power and/or pull

the plug out of the wall outlet.

•

Keep hands, long hair, clothing, ties, jewelry

and loose items away from the feed opening

and shred outlet.

•

Do not use the shredder for anything other

than its intended purpose. Never use it to

shred cloth, plastic, cardboard or any hard

material that will cause damage to the

shredder blades.

DO NOT SHRED STAPLES OR PAPER CLIPS, THEY WILL

DAMAGE OR DESTROY THE CUTTING BLADES.

•

Do not allow children to use the machine.

•

Do not operate with a damaged power cord or plug, or when the machine

damaged in any manner.

•

Unplug the shredder when it is being moved, or if it is not in use for an

extended

period of time.

•

Do not disconnect the power by pulling only the cord. Hold the plug when

disconnecting.

•

Keep the shredder away from direct sunlight.

•

Do not sit on the shredder or place anything on top of it.

•

Never open the ﬁ xed switch or cover.

Andere Handbücher für FD 8400HS

Andere Formax Aktenvernichter Handbücher

Formax

Formax FD 8500HS Bedienungsanleitung

Formax

Formax FD 8302SC Bedienungsanleitung

Formax

Formax FD 8250CC Bedienungsanleitung

Formax

Formax FD 87HDS Bedienungsanleitung

Formax

Formax FD 8502AF Bedienungsanleitung

Formax

Formax FD 8302CC Bedienungsanleitung

Formax

Formax FD 8204CC Bedienungsanleitung

Formax

Formax FD 8650CC Bedienungsanleitung

Formax

Formax FD 87HD Bedienungsanleitung

Formax

Formax FD 8732HS Bedienungsanleitung

Formax

Formax FD 8400HS Bedienungsanleitung

Formax

Formax FD 8502CC Bedienungsanleitung

Formax

Formax FD 8650HS Bedienungsanleitung

Formax

Formax FD 8500AF Bedienungsanleitung

Formax

Formax FD 8500CC Bedienungsanleitung

Formax

Formax FD 8402CC Bedienungsanleitung

Formax

Formax FD 8802 series Bedienungsanleitung

Formax

Formax FD 8732HS Bedienungsanleitung

Formax

Formax FD 8202CC Cross-Cut Bedienungsanleitung

Formax

Formax FD 8704CC Bedienungsanleitung

Formax

Formax FD 8804CC Montageanleitung

Formax

Formax FD 8254CC Bedienungsanleitung

Formax

Formax FD 8602CC Bedienungsanleitung

Formax

Formax OnSite FD 87 Bedienungsanleitung

Beliebte Aktenvernichter Handbücher anderer Marken

Swingline

Swingline STACK-AND-SHRED200X&200XL 60X Bedienungsanleitung

GBC

GBC ShredMaster CC055 Bedienungsanleitung

UNITED OFFICE

UNITED OFFICE UAV 190 A1 Bedienungsanleitung

Rexel

Rexel Optimum AutoFeed+ 45X Bedienungsanleitung

Martin Yale

Martin Yale 227284S1 Bedienungsanleitung

Bonsaii

Bonsaii DocShred C223-A Bedienungsanleitung

HSM

HSM Pure 740 max Bedienungsanleitung

TRU RED

TRU RED TR-BMC20A Bedienungsanleitung

Fellowes

Fellowes 50S Bedienungsanleitung

GBC

GBC SHREDMASTER 1236SE Bedienungsanleitung

Gude

Gude GH 2600 P Bedienungsanleitung

Ativa

Ativa DQ80M Bedienungsanleitung

Q-Connect

Q-Connect Q8CC Bedienungsanleitung

Fellowes

Fellowes POWERSHRED C-325CI Bedienungsanleitung

Olivetti

Olivetti Privacy 5000C Kurzanleitung

Dahle

Dahle paperSAFE 22022 Bedienungsanleitung

GEHA

GEHA Home & Office S7 CD Bedienungsanleitung

Fellowes

Fellowes Powershred M-3C Bedienungsanleitung