Formax FD 8802 series Bedienungsanleitung

Instruction Manual

Provided By

http://www.MyBinding.com

http://www.MyBindingBlog.com

Formax FD 8802

Series Shredders

Industrial Conveyor Shredders

FD 8802CC Cross-Cut

FD 8802SC Strip-Cut

OPERATOR/

MAINTENANCE

MANUAL

SECOND EDITION

10/07

The serial number is speciﬁ ed on the nameplate of the shredder. Guarantee claims and inquiries cannot be

processed if you do not quote the serial number.

Enter this number into the nameplate shown here immediately after receipt of the shredder.

MACHINE SPECIFICATIONS

Model Type

FD 8802CC

FD 8802SC

Serial #:

Shred Size:

1/4” x 2”

1/2”

Sheet Capacity:

75 - 90

105 - 125

Speed:

Up to 40 fpm

Up to 50 fpm

Throat Width:

16”

Waste Bin Capacity:

36 gallons

49 gallons

Motor:

8HP

Power:

3-Phase, 220V, 50/60Hz, both models

Weight:

661 lbs.

TABLE OF CONTENTS

TOPIC

PAGE

Safety Precautions

1-2

Checking Safety Devices

Overview

Machine Characteristics

Cutting Data, Speed, Dimensions, Weight

Motor Speciﬁ cations, Power Requirements

Installation

Start-up: Main Switch and Control Panel

Operation, Overloading

Maintenance: Emptying Waste Bin

Maintenance: Removing Side Covers

Maintenance: Conveyor Belt Maintance

8-9

Maintenance: Lubricating Shredder Mechanisms

Maintenance: Exterior Cleaning

Installation: Optional EvenFlow Oiler

Parts Lists

12-21

“Work safety” symbol

This symbol marks all work safety notes in this manual which can endanger the health

or life of operators. Please pay attention to this symbol and exercise particular care in

such cases. Please also forward all work safety notes to other users.

Apart from the instructions in this manual, you should also follow generally

applicable safety and accident prevention regulation.

Notes on work safety

The FD 8802 shredder has been inspected for safety. However, improper operation and misuse risk the

following:

•

the health or life of the operator

•

the machine and other valuable equipment

•

the efﬁ cient operation of the shredder.

The FD 8802 employs state-of-the-art technology and is safe to operate. However, this machine can become

hazardous if used incorrectly, by untrained staff or for purposes other than those for which it is designed.

•

Material with a tendency to curl, e.g. tapes, cords, etc. should not be processed.

•

Keep long hair, loose clothes, ties, scarves, etc. away from paper feed opening.

•

Only one person should operate the shredder at a time.

•

Always follow local safety and accident prevention regulations when operating the shredder.

•

No pedestals or other raised surfaces may be placed in the vicinity of the machine if they alter the

safety clearances.

•

All connecting cables must be laid in such a way that they cannot be tripped over.

•

Mechanical wearing parts must be inspected once a year.

“Attention” notes

This icon marks information in this manual which requires particular attention including

guidelines, regulations, instructions and correct working procedures intended to prevent

damage to the machine and/or other equipment.

Safety Precautions

The FD 8802 shredder is intended

only

for shredding paper, paperboard and cardboard. It is designed

for shredding large volumes of archive ﬁ les, bound EDP lists and the contents of waste paper bins. The

hardened, solid-steel cutting rollers are unaffected by loose-leaf binders, paper clips and staples contained in

these materials.

Any other use beyond the scope described here is regarded

as not being in accordance with the instructions.

The manufacturer will not be held liable for damage resulting from incorrect use; the user alone is responsible.

Users must also follow the assembly, dismantling, re-assembly, operation and maintenance procedures

speciﬁ ed by the manufacturer. The operation, maintenance and repair of the machine must be performed only

by trained personnel who are aware of the potential dangers.

The relevant accident prevention regulations as well as other generally recognized rules concerning safety

engineering and occupational safety must be observed.

•

Each person responsible for assembling, dismantling and reassembling and maintenance (inspection,

servicing, repair) of the shredder must have read and fully understood the entire operating manual, in

particular the "Safety" section.

•

The shredder may only be operated, serviced and repaired by authorized, trained personnel.

•

The shut-down procedures speciﬁ ed in this manual must be followed during all assembly, dismantling

and re-assembling, cleaning, and maintenance work. This type of work must be performed only when

the machine is idle.

•

The drive of the FD 8802 must be secured against unintentional switching-on before performing

work on the machine. Set the main switch to "Off" and unplug machine from wall outlet.

•

After repair, check all protective devices to be sure they have been re-installed before operation.

•

Do not perform any work which may impair your safety while operating the machine.

•

Immediately report any changes which impair your safety to the person responsible. Shut the machine

down until such damage has been resolved.

•

Before operating the shredder, ensure that it is in perfect working condition.

•

Ensure that the workplace around the FD 8802 is always clean and safe.

•

The user must not make any conversions or changes on his own initiative which impair the safety of

the FD 8802. Protective devices must not be removed or rendered inoperative.

•

All work which is not directly connected to the normal operation of the machine must always be

performed when the machine is idle.

•

Doors and ﬂ aps must not be opened until the machine is motionless. Observe safety labels!

•

Test the safety features after installing or repairing electrical components.

Checking the safety devices

Check the safety devices:

•

at the start of each work shift (when operation is sporadic)

•

at least once a week in continuous operation

•

after each maintenance or repair

Check the safety devices for:

•

speciﬁ ed condition

•

speciﬁ ed location

•

safe attachment

•

speciﬁ ed function

Correct defects before you operate the shredder.

1. Immediately shut down the shredder if defects occur during operation and make sure the defects are

corrected.

2. Do not modify or remove protective devices. Do not switch off protective devices. For safety reasons,

modiﬁ cations of the machine are not allowed.

Danger:

Defective safety devices can cause serious accidents. If safety devices are not

working properly, the shredder should immediately be put out of operation.

Never

reach into the cutting system while it is operating; you risk serious injury!

Only when all safety devices are operating correctly can the shredder be used again.

Operate the shredder only when these devices have been checked and are in order.

1. Check the

Safety Bar

push button (A) in front of the feeding table:

Safety Bar push button (A) in front of the feeding table: Safety Bar

The shredder must switch off immediately when you press the

Safety Bar

button and the Emergency

Safety Bar button and the Emergency Safety Bar

stop light must go on.

2. Check the

Stop

button (B) on the right of the

control panel:

The shredder must switch off immediately

when the button is pushed.

3. Check the

Safety Switch

inside the Cutting

Block Access Door at the top of the shredder (C).

Press the door handle release. Handle will rotate

up. Pull up on handle.

The shredder must switch off immediately

when the door is opened.

General Overview

Front View with Waste Bin

Control Panel and

Cutting Block Access Door

Breaker Panel

Feed Table

Safety Bar

Right Side View with Electricity

Control Box Access Door

Machine characteristics

Machine designation: conveyor-belt paper shredder

Machine type: FD 8802CC, FD 8802SC

Total machine weight: 661 lbs.

Technical equipment: large feeding table, inlet conveyor belt

Cutting Data, Speed, Dimensions, Weight

Cutting Style:

Cross Cut

Strip Cut

Shred Size:

1/4” x 2”

1/2”

Sheet Capacity:

75 to 90

105 to 125

Speed:

Up to 40 feet per minute

Up to 50 feet per minute

Feed Opening:

16”

Dimensions:

29” W x 48 3/4” D x 47” H

29” W x 53” D x 50 1/2” H

Feed Table Dimensions:

28 1/4” W x 16” D x 37 1/2” H

28 1/4” W x 16” D x 41 1/2” H

Space Requirements:

32” W x 51” L x 55” H

32” W x 55” L x 59” H

Waste Bin Capacity:

36 gal.

49 gal.

Weight:

661 lbs.

FD 8802CC

Motor Speciﬁ cations, Power Requirements

Installation

1. Appropriate power outlet must be available at installation site.

2. The FD 8802 is delivered completely assembled (although it can be

delivered in parts, if necessary.) During transport, be aware of the

shredder’s high center of gravity.

3. The shredder can be moved on its casters. If a fork-lift is used to transport

the machine, be sure to use the designated pick-up points.

4. Install the shredder on a ﬂ at and even ﬂ oor without carpeting.

5. Once the shredder is in place, lock the caster brakes, and plug in power

cable to appropriate power source.

Power Plug

Power Outlet

Motor Type

Horizontal Geared

Rated Power

8HP

Operating Voltage

220V

Phase

3-Phase

Frequency

50/60Hz

Rated Current

20A

Output RPM

25 RPM

Number of Poles

4 (3 hot & 1 ground)

Total Rated Power Pn

1.5KW

Total Rated Current In

20A

Total EOCR Protection

25A

FD 8802SC

Control Panel

DOOR OPEN

Indicator lights to show

when waste bin door is

open. (Shredder will not

operate if door is open.)

REVERSE

Blue Touch Pad

Push button to reverse

direction of cutting blades.

STOP

Red Touch Pad

Push button to stop

cutting system. Shredder

remains in standby mode

until Start is pressed.

START

Green Touch Pad

Push to start conveyor and cutting

blade operation. Cutting system

operates in feed direction.

Start-up and Operation

Main Switch

1. On the right side of the machine, open the orange door leading to the electrical control panel. Push on the

lever (Fig. 1) and the handle will pop out. Pull to open (Fig. 2).

2. Flip the main power switch to the UP position (Fig. 3).

3. Insert key into On-Off switch to right of control panel (Fig. 4). Turn key right, to the On position.

Fig. 1

Fig. 2

Fig. 3

Main Power Switch

MODE INDICATORS

Indicators light to show the

shredder’s status: Auto,

Manual, Stop, Reverse

WASTE BIN FULL

Indicator lights when

waste bin is full of

paper shreds.

LOAD INDICATOR

Lights to show how

close shredder is

to capacity, or if

overloaded.

Fig. 4

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Formax Aktenvernichter Handbücher

Formax

Formax FD 8252CC Bedienungsanleitung

Formax

Formax FD 8602CC Bedienungsanleitung

Formax

Formax FD 87 Montageanleitung

Formax

Formax FD 8730HS Bedienungsanleitung

Formax

Formax FD 8254CC Bedienungsanleitung

Formax

Formax FD 8850CC Bedienungsanleitung

Formax

Formax FD 8502AF Bedienungsanleitung

Formax

Formax FD 8704CC Bedienungsanleitung

Formax

Formax FD 8650HS Bedienungsanleitung

Formax

Formax FD 8250CC Bedienungsanleitung

Formax

Formax FD 8302SC Bedienungsanleitung

Formax

Formax FD 8652CC Bedienungsanleitung

Formax

Formax OnSite FD 87 Bedienungsanleitung

Formax

Formax FD 8400HS Bedienungsanleitung

Formax

Formax FD 8500CC Bedienungsanleitung

Formax

Formax FD 8400HS Bedienungsanleitung

Formax

Formax FD 87HDS Bedienungsanleitung

Formax

Formax FD 8302CC Bedienungsanleitung

Formax

Formax FD 8906CC Cross-Cut Bedienungsanleitung

Formax

Formax FD 8702CC Bedienungsanleitung

Formax

Formax FD 8804CC Montageanleitung

Formax

Formax FD 8402CC Bedienungsanleitung

Formax

Formax FD 8300HS Bedienungsanleitung

Formax

Formax FD 8730HS Bedienungsanleitung

Beliebte Aktenvernichter Handbücher anderer Marken

Swingline

Swingline STACK-AND-SHRED200X&200XL 60X Bedienungsanleitung

GBC

GBC ShredMaster CC055 Bedienungsanleitung

UNITED OFFICE

UNITED OFFICE UAV 190 A1 Bedienungsanleitung

Rexel

Rexel Optimum AutoFeed+ 45X Bedienungsanleitung

Martin Yale

Martin Yale 227284S1 Bedienungsanleitung

Bonsaii

Bonsaii DocShred C223-A Bedienungsanleitung

HSM

HSM Pure 740 max Bedienungsanleitung

TRU RED

TRU RED TR-BMC20A Bedienungsanleitung

Fellowes

Fellowes 50S Bedienungsanleitung

GBC

GBC SHREDMASTER 1236SE Bedienungsanleitung

Gude

Gude GH 2600 P Bedienungsanleitung

Ativa

Ativa DQ80M Bedienungsanleitung

Q-Connect

Q-Connect Q8CC Bedienungsanleitung

Fellowes

Fellowes POWERSHRED C-325CI Bedienungsanleitung

Olivetti

Olivetti Privacy 5000C Kurzanleitung

Dahle

Dahle paperSAFE 22022 Bedienungsanleitung

GEHA

GEHA Home & Office S7 CD Bedienungsanleitung

Fellowes

Fellowes Powershred M-3C Bedienungsanleitung