FREE MOTION Reflex T11.8 Bedienungsanleitung
Freemotion Reflex t11.8 Treadmill Assembly Manual:
Refer to when disassembled in 3 pieces
6
Thank you for selecting the revolutionary
FREEMOTION®REFLEX T11.8 treadmill. The REFLEX
T11.8 treadmill offers an impressive selection of fea-
tures designed to make your workouts more enjoyable
and effective.
For your benet, read this manual carefully before
using the treadmill. If you have questions after
reading this manual, please see the back cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
BEFORE YOU BEGIN
Handrail
Console
Key/Clip
Power Switch
Walking Belt
Idler Roller
Adjustment Screws
Heart Rate Monitor
Walking Platform
Accessory Tray
Length: 7 ft. 2 in. (218 cm)
Width: 2 ft. 10 in. (86 cm)
Foot Rail
7
#8 x 2 1/4" Machine Screw (3)–6
#8 x 1/2" Machine
Screw (4)–2
#6 x 5/8" Machine
Screw (110)–2
3/8" x 2 3/4" Bolt (2)–2
1/4" Star
Washer (5)–4
3/8" Flat
Washer (43)–5
3/8" x 3 1/4" Screw (1)–6
3/8" x 3 3/4" Screw (11)–4
#8 x 5/8"
Screw (18)–2
3/8" Star
Washer (2)–7
3/8" x 2 3/4" Screw (27)–4
PART IDENTIFICATION CHART
Use the drawings below to identify small parts used for assembly. The number in parentheses below each draw-
ing is the key number of the part, from the PART LIST near the end of this manual. The number following the key
number is the quantity used for assembly. Note: If a part is not in the hardware kit, check to see if it is preat-
tached. Extra hardware may be included.
8
• Assembly requires two persons.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materialsuntilyounishallassemblysteps.
• To identify small parts, see page 7.
• After shipping, there may be an oily substance
on the exterior of the treadmill. This is normal. If
there is an oily substance on the treadmill, wipe
it off with a soft cloth and a mild, non-abrasive
cleaner.
• Assembly requires the following tools:
the included hex key
one adjustable wrench
one Phillips screwdriver
To avoid damaging parts, do not use power tools.
ASSEMBLY
1. Make sure that
the power cord
is unplugged. Be
careful not to pinch
the power cord.
Slide the Upright Cover (not shown) off the
Upright (81).
Orient the Upright (81) and the plastic ties as
shown. Set the Upright on the tabs on the Frame
(53). Attach the Upright to the Frame with six
3/8" x 3 1/4" Screws (1), three 3/8" Star Washers
(2), and three 3/8" Flat Washers (43). Start all
six Screws before tightening them. Be careful
not to pinch any wires.
81
53
1
1
2
Plastic Ties
1
!
!
43
9
2. Insert the end of the Upright Wire (111) through
the looped plastic tie at the top of the Upright
(81). Make sure that the Upright Wire is
behind the crossbars on the Upright. Then,
gently pull upward on the Upright Wire as you
tighten the plastic ties around the Upright Wire.
Repeat this step for the TV Cable (106).
111
2
Plastic Ties
81
Crossbar
Crossbar
Crossbar
3. Slide the Upright Cover (80) downward onto
the Upright (81). Be careful not to pinch the
Upright Wire (111) or the TV Cable (106). Be
careful not to hit the ceiling with the Upright
Cover.
Make sure to orient the Upright Collar (105)
so that the sticker is on the side indicated.
Slide the Upright Collar onto the Upright Cover
(80).
80
3
81
106
111
106
105
Sticker
10
4. Have a second person hold the handrail assem-
bly near the Upright (81). Insert the Upright Wire
(111) and the TV Cable (106) upward through
the center of the handrail assembly.
Slide the bracket on the handrail assembly over
the crossbar on the Upright (81) and set the
handrail assembly on the Upright. Be careful
not to pinch any wires.
Handrail
Assembly
4
81
Bracket
111
Crossbar
5. Attach the handrail assembly with two 3/8" x
3 3/4" Screws (11) and two 3/8" Star Washers
(2). Start both Screws, but do not tighten
them yet. Be careful not to pinch any wires.
5
Handrail
Assembly
106
11
2
11
6. Tighten two 3/8" x 3 3/4" Screws (11) with two
3/8" Flat Washers (43) into the handrail assem-
bly. Start both Screws, and then tighten them.
See step 5. Tighten the two 3/8" x 3 3/4"
Screws (11).
6
Handrail
Assembly
43
7. Have a second person hold the Console
Assembly (101) near the handrail assembly.
Connect the Upright Wire (111), the handrail
wire, and the TV Cable (106) to the console
wires. Make sure that the console wire and
the handrail wire that you are connecting have
connectors that are the same size. See the
inset drawing. The connectors should slide
together easily and snap into place. If they
do not, turn one connector and then try again. IF
THE CONNECTORS ARE NOT CONNECTED
PROPERLY, THE CONSOLE MAY BE DAM-
AGED WHEN THE POWER IS TURNED ON.
Insert the excess wires downward into the
Upright Cover (80).
Set the Console Assembly (101) on the handrail
assembly. Be careful not to pinch any wires.
7
80
101
111
Console
Wires
Handrail
Assembly 106
Handrail
Wire
11
12
10. If necessary, move the treadmill to the desired
location (see HOW TO MOVE THE TREADMILL
on page 28).
After the treadmill is placed in the location where
it will be used, make sure that the Leveling Feet
(64) rest firmly on the floor. If the treadmill rocks
even slightly, loosen one of the 1/2" Nuts (36) on
a Leveling Foot, turn the Leveling Foot clockwise
or counterclockwise until the rocking motion is
eliminated, and then retighten the Nut.
64
10
11. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of plastic
on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill.
Note: Extra hardware may be included. Keep the included hex key in a secure place; the hex key is used to
adjust the walking belt (see pages 34 and 35).
36
18
9
Handrail
Assembly
105
9. Attach the Upright Collar (105) to the handrail
assembly with two #8 x 5/8" Screws (18).
18
27
8. Tighten four 3/8" x 2 3/4" Screws (27) with two
3/8" Star Washers (2) into the handrail assembly. 8
27
2
2
Handrail
Assembly
Inhaltsverzeichnis
Andere FREE MOTION Tretmühle Handbücher
FREE MOTION
FREE MOTION t 6.4 Bedienungsanleitung
FREE MOTION
FREE MOTION Treadmill Bedienungsanleitung
FREE MOTION
FREE MOTION t 5.6 Bedienungsanleitung
FREE MOTION
FREE MOTION FMRET74811.0 Bedienungsanleitung
FREE MOTION
FREE MOTION SFTL25808.0 Bedienungsanleitung
FREE MOTION
FREE MOTION REFLEX T11.4 Bedienungsanleitung
FREE MOTION
FREE MOTION SFTL90009.0 Bedienungsanleitung
FREE MOTION
FREE MOTION t8.7 Bedienungsanleitung
FREE MOTION
FREE MOTION t10.8 Bedienungsanleitung
FREE MOTION
FREE MOTION Incline trainer Bedienungsanleitung
FREE MOTION
FREE MOTION 790 Interactive Bedienungsanleitung
FREE MOTION
FREE MOTION SFTL15609.0 Bedienungsanleitung
FREE MOTION
FREE MOTION FMTK75009.0 Bedienungsanleitung
FREE MOTION
FREE MOTION SFSR81908.0 Bedienungsanleitung
FREE MOTION
FREE MOTION XTr Bedienungsanleitung
FREE MOTION
FREE MOTION VFMTL1106.0 Bedienungsanleitung
FREE MOTION
FREE MOTION R0209A Bedienungsanleitung
FREE MOTION
FREE MOTION XTR 90 Bedienungsanleitung
FREE MOTION
FREE MOTION Treadmill Bedienungsanleitung
FREE MOTION
FREE MOTION SFTL27808.0 Bedienungsanleitung
Beliebte Tretmühle Handbücher anderer Marken
Smooth Fitness
Smooth Fitness EVO 3i Bedienungsanleitung
NordicTrack
NordicTrack NETL81810.0 Bedienungsanleitung
Schwinn
Schwinn 830/Journey 8.0 Bedienungsanleitung
Keys Fitness
Keys Fitness HealthTrainer HT-740T Bedienungsanleitung
Spirit
Spirit XT8 Bedienungsanleitung
NordicTrack
NordicTrack T 14.0 Treadmill Bedienungsanleitung