FS FFOI-606 Bedienungsanleitung
DESKTOP VIDEO 3D MICROSCOPE
FFOI-606/FFOI-607
Quick Start Guide V1.0
JW1
JW2
JW3
JW4
JW5
JW6
LC-F
POWER
USB
JW1
JW2
Introduction
Desktop video three-dimensional (3D) microscope integrates the display and scope all together to
greatly convenience the operation and improve the efficiency, it has a great advantage with high
resolution, light weight and multiples port support, posit and negative images etc. It's super well
suitable for fiber kits manufacturer inspection.
Accessories
Power Adaptor x1
FFOI-606/FFOI-607
Optional (Not Included)
SD Card x1 Conversion Head x1
Adapter
Lock
Battery x1
JW1
JW2
JW3
JW4
JW5
JW6
POWER
USB
JW1
JW2
JW3
JW4
JHOTA
18650-11.1V-3400mAh
MF-SC-F x1LC-F x1 2.5PC-M x1 1.25PC-M x1
FFOI-607
M3 x12 Screwdriver x1
Optional (Not Included)
FFOI-606
LC-PC/APC x1FC-PC/APC x1 SC-PC/APC x1 OM-08 x1
Function Introductions
BNC/AV
OUT
USB
OUT Probe
IN
DC 12V
K1
K2
IN
22 21 20
19
18
17
LC-F
JW1
JW2
JW3
JW4
JW5
JW6
1
25
6
7
8
9
10
4
11
3
12 13 14 15 16
POWER
USB
23
Body Shell
Y, X-Axis Adjustment
Knob
Power Indicator
Negative Key (JW1)
Adjustment Keys
(JW3, JW4)
When power is on, the light is on. When switch to
battery for power the light flashes for low display.
Highlight Key (JW2) Used to highlight the fuzzy, shallow and subtle
scratches for easy observation.
Used to adjust the display brightness, contrast
and color.
The use of high-strength plastic, lightweight,
wear-resistant, no deformation, colors choosable.
NO.
1
TFT Display 8.0-inch LCD screen with high resolution and
brightness.
2
3/4
5
6
9
7/8
Clamp
Mainly to play a fixed and positioning role on fiber
end, different fibers need corresponding different
clamp for test.
12
13
USB Indicator When the USB is connected to the computer, the
light is on.
14
Menu Key (JW5) Display options menu key.
Display Key (JW6) Turns the display on and off.10
Brightness Adjustment
Knob
Adjust the brightness of the light source at the end
of the light source, for easy and clear observation.
11
Battery Box, Storage Box Storage for DC lithium batteries (optional), fixtures
or other accessories.
17
Power Switch 0 for power off, K1 for power on for work, K2 for
power on with external scope connection.
18
Power Interface 12V dedicated power interface.19
Scope-In Interface Used to connect hand-held scope.20
USB Function Interface
(Optional)
USB output digital image to the computer,
professional viewing and analysis software
can be offered to check.
21
BNC Video Output Interface Can output CRT display dedicated signal.22
SD Card Slot (Optional) Insert SD card for storing detection images.23
Button Description
Focusing Wheel Flip the wheel clockwise or counterclockwise to
make sure the end face can be adjusted to show.
15
16 Lens Adjustment Seat 70 series of aluminum, hard wear, excellent surface.
Adjust with the knob up and down, left and right
movement, one by one to observe the end of
each fiber.
Hold to press the key for 3 seconds, the display
shows negative image specially for small scratches
observation, and then press 3 seconds to switch
back for normal image.
Installing
FFOI-606
JW3
JW4
JW5
JW6
POWER USB
JW5
JW6
JW4
JW3
JW2
JW1
1. Mount the clamp on the microscope with two M3 screws.
2. Insert the MTP trunk cable to be detected.
FFOI-607
3. Insert the LC fiber patch cable to be detected.
JW1
JW2
JW3
JW4
JW5
JW6
POWER USB
LC-F
JW4
JW5
JW6
POWER USB
LC-F
1. Counterclockwise rotation to remove the original clamp.
2. Replace with the clamp you need to install, turn clockwise to tighten.
JW1
JW2
JW3
JW4
JW5
JW6
POWER USB
Operation Instructions
Step 1: After the power is on, set the power key to K1, insert the fiber jumper or fiber optic device,
adjust the focus wheel until you observe the clear fiber end-face image.
Step 2: Use the external hand-held scope: connect the scope (currently only support the company’s
scope) with the device from scope-in port, switch the power key to K2 for observation.
Step 3: Keep holding “JW1” key (3 seconds) into the negative image mode to facilitate clear observation
of subtle scratches, then keep holding (3 seconds) to switch back to normal observation.
Step 4: In the negative image mode, keep holding“JW2” (3 seconds), the vague or shallows scratches
will be highlighted, simple subtle scratches can be easily spotted, of course image noise also
increases at the same time.
Positive Negative
Step 5: Adjust the display contrast, brightness, color and sharpness:
1. Contrast adjustment: press“JW5” into contrast adjustment, press “JW3” to reduce contrast, press
“JW4” to increase contrast.
Maintenance
(1) For the first time use, if no image finds, please adjust the X/Y axis for callbration until the light from
source hole is positioned in the center. Please do not move any screws or kits since the microscope is
well organized in factory before any delivery.
(2) Take care of the clamp for long use and replace it if it has too much swear and wear. Please keep lens
clean and away from being contaminated by dusts and other residues for long use.
2. Brightness adjustment: press“JW5” into brightness adjustment, press “JW3” to reduce the brightness,
press “JW4” to increase the brightness.
3. Color adjustment: press“JW5” into color adjustment, press“JW3” to reduce the gray, press “JW4” to
increase the gray.
4. Sharpness adjustment: press “JW5” into sharpness adjustment, press “JW3” to reduce the clarity, press
“JW4” to increase the clarity.
Online Resources
Download https://www.fs.com/download.html
Help Center https://www.fs.com/service/help_center.html
Contact Us https://www.fs.com/contact_us.html
Copyright © 2020 FS.COM All Rights Reserved.
Q.C. PASSED
FS ensures our customers that any damage or faulty items due to our workmanship, we will offer a
free return within 30 Days from the day you receive your goods.
Warranty: All Fiber Optic Inspections enjoy 1 year limited warranty against defect in
materials or workmanship. For more details about warranty, please check at
https://www.fs.com/policies/warranty.html
Return: If you want to return item(s), information on how to return can be found at
https://www.fs.com/policies/day_return_policy.html
Product Warranty
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere FS Mikroskop Handbücher
Beliebte Mikroskop Handbücher anderer Marken
Thermo Scientific
Thermo Scientific Nicolet iN10 Leitfaden
National
National DC3-163 Bedienungsanleitung
KERN Optics
KERN Optics OPE-1 Bedienungsanleitung
OPTIKA MICROSCOPES
OPTIKA MICROSCOPES B-150D Bedienungsanleitung
Prior
Prior Lux POL Bedienungsanleitung
Opitec
Opitec Smartscoop 115615 Bedienungsanleitung
VWR
VWR VisiScope 384 Series Bedienungsanleitung
Nikon
Nikon ECLIPSE E200 POL Bedienungsanleitung
Leica
Leica DI C800 Handbuch
ThermoFisher Scientific
ThermoFisher Scientific Continuµm Bedienungsanleitung
ThermoFisher Scientific
ThermoFisher Scientific Continuµm Bedienungsanleitung
Olympus
Olympus SZ61 Bedienungsanleitung