Fujitsu PRIMERGY RX1330 M4 Bedienungs- und Montageanleitung

PRIMERGY CUSTOMER INFORMATION BULLETIN

Number/Revision:

PY-CIB049-00

Issue Date:

14 April 2020

Title:

The System Tries to Power on Before iRMC is Ready

Applies to:

PRIMERGY RX1330 M4/TX1330 M4/TX1320 M4

Effective Duration:

Permanent

Problem:

When the power is connected to the PRIMERGY server, the system tries to start before

the Fujitsu Integrated Remote Management Controller (iRMC) is ready. This is indicated

by the fans speeding up to the maximum as soon as the power is connected. The iRMC

takes about two minutes to boot up, then you see the display on the screen indicating

POST and the fans slow down to normal speed.

This is not expected behavior. The iRMC should boot up first indicated by a stable

power LED. The system can then be started using the power switch (or remotely using

the iRMC interface).

Solution / Workaround:

This issue is resolved by the following procedure:

PRIMERGY CUSTOMER INFORMATION BULLETIN

1. Disconnect the power cables

2. Open the housing and locate the jumper block for UEFI Recovery (RCVR) /

Password Clear (PWD CLR)

Consult the relevant PRIMERGY Maintenance Manual from

http://manuals.ts.fujitsu.com for help to open the housing

The board schematic sticker on the inside can guide to the location of the

RCVR/PWD CLR jumper block

See an example of the jumper block in Fig.1 and a schematic on Fig.1a

below showing the neutral position (Default)

Fig. 1: Jumper in neutral position

3. Set the jumper to ‘PWD CLR’ position as shown in Fig. 2 and Fig. 2a (schematic)

4. Connect the power cables. The fans will still speed up. Wait until the monitor

displays POST after about 2 minutes by when the iRMC should be ready. A

PRIMERGY CUSTOMER INFORMATION BULLETIN

warning message will be displayed indicating the jumper is placed in a password

clear position.

5. Enter UEFI (BIOS) setup, go to ‘Save and Exit’ tab and choose ‘Save Changes

and Reset’

6. Disconnect the power cables

7. Place the jumper in the neutral position (see Fig. 1/1a)

8. Close the housing

9. Connect the power cables. The system will not start before the iRMC is ready

10.Power On the system as soon as the iRMC is ready (when the power LED stops

blinking)

Do not be concerned if the system switches off in POST and starts again

11.Enter UEFI (BIOS) setup, check and correct the necessary settings (especially

SATA operation mode if you are using the onboard SATA RAID functionality)

12.After the desired BIOS settings are set make sure to ‘Save Changes and Reset’

Revision History

REVISION

DATE

CHANGE SUMMARY

0000

14 April 2020

Initial Release

Andere Handbücher für PRIMERGY RX1330 M4

2

Dieses Handbuch passt für folgende Modelle

2

Inhaltsverzeichnis

Andere Fujitsu Server Handbücher

Fujitsu

Fujitsu PRIMERGY RX800 S2 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY SX650 Montageanleitung

Fujitsu

Fujitsu PRIMERGY TX300 S7 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY H200 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY RX2530 M1 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX620 S6 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX600 Leitfaden

Fujitsu

Fujitsu BX630 - PRIMERGY - S2 Dual Bedienungsanleitung

Fujitsu

Fujitsu BS2000 SE Series Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY TX200 S2 Leitfaden

Fujitsu

Fujitsu Primergy RX4770 M1 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY RX2530 M6 Bedienungsanleitung

Fujitsu

Fujitsu Primergy CX270 S2 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY DX920 S3 Handbuch

Fujitsu

Fujitsu PRIMERGY TX140 S2 Bedienungsanleitung

Fujitsu

Fujitsu FUTRO S9010 Bedienungsanleitung

Fujitsu

Fujitsu SPARC M12-1 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX620 S4 Bedienungsanleitung

Fujitsu

Fujitsu BS2000 SE Series Bedienungsanleitung

Fujitsu

Fujitsu SPARC Enterprise T5440 Server Installationsanleitung

Fujitsu

Fujitsu PRIMEQUEST 3000 Series Bedienungsanleitung

Fujitsu

Fujitsu FUTRO S930 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY RX300 S6 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY TX1320 M4 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung