Gamma+ Luxe Cannon 600 Z IP Bedienungsanleitung

①

Leko Cannon

LED 300

(CW/WW)

User Manual

IP65

Luxé Cannon

600 Z IP (VW)

②

SAFETY INSTRUCTIONS

This device has left the factory in perfect condition. In order to maintain this condition and

to ensure a safe operation, it is absolutely necessary for the user to follow the safety

instructions and warning notes written in this user manual.

If the device has been exposed to temperature changes due to environmental changes, do

not switch it on immediately. The arising condensation could damage the device.

Leave the device switched off until it has reached room temperature.

This device falls under protection-class I. Therefore it is essential that the device be

earthed.

The electric connection must carry out by qualified person. The device shall only be used

with rate voltage and frequency.

Make sure that the available voltage is not higher than stated at the end of this manual.

Make sure the power cord is never crimped or damaged by sharp edges. If this would be

the case, replacement of the cable must be done by an authorized dealer.

Always disconnect from the mains, when the device is not in use or before cleaning it. Only

handle the power cord by the plug. Never pull out the plug by tugging the power cord.

During initial start-up some smoke or smell may arise. This is a normal process and does

not necessarily mean that the device is defective, it should decrease gradually.

Please don't project the beam onto combustible substances.

Fixtures cannot be installed on combustible substances, keep more than 50cm distance

with wall for smooth air flow, so there should be no shelter for fans and ventilation for heat

radiation.

Becareful with your operations.With a dangerous voltage you cansuffer

a dangerous electric shock when touching wires!

Damages caused by the disregard of this user manual are not subject to

warranty. The dealer will not accept liability for any resulting defects or

problems.

③

If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively

replaced by the manufacturer or his service agent or a similar qualified person in order to

avoid a hazard.

Please pay attention below warnings before using

this fixture!

④

Unpacking

Thank you for choosing Leko Cannon 300 -CW+WW. For your own safety, please read this

manual before installing the device. This manual covers the important information on installation

and applications. Please install and operate the fixture with following instructions. Meanwhile,

please keep this manual well for future needs.

The Leko Cannon 300 -CW+WW is made of a new type of high temperature strength of die cast

aluminum casing with nice outlook. The fixture is designed and manufactured strictly following

CE&RoHS standards, complying with international standard DMX512 protocol. It's available

independently controlled and linkable with each other for operation. And it is applicable for

large-scale live performances, theater, studio, nightclubs and discos.

The Leko Cannon 300 adopts 1PCS 600W COB LED (available for cool white+warm white 2in1)

which features high brightness and stability. Please carefully unpack it when you receive the

fixture and check whether it is damaged during the transportation. And please check whether the

following items are included inside the box:

①

②

⑤

③

FEATURES & SPECIFICATIONS

Feature

：

* 1 * 300W COB LED (Cool White+Warm White 2in1)

* Color temperature: 3000K-6000K

* 50,000 hours life time and low power consumption

* Optimized high definition optical system for improved photometric performance and field

uniformity

* Projector-quality, high contrast aspheric lens

* Glass reflector that removes greater than 90% infrared radiation (heat) and reflects greater than

95% of visible light

* Input Voltage:AC100-240V 50/60Hz

* Beam Angle: 15°to 30°

* Zoom Function: Auto zoom by DMX

* Shutter controlled by DMX (auto cutting to any shapes)

* Die casting aluminum housing design

* 4 kinds of dimming curve

* Dimming Frequency: 500HZ - 25000HZ optional

* High-quality optical system, glass aspherical

* 17 DMX channels

* Control Protocol: RDM / DMX , Auto run and Master/Slave control system

* LCD with touch screen

* Fan-less no noise Cooling system

* Working Temperature: -10℃~40℃

* IP65 protection rating

① Leko Cannon

300-CW+WW

1PC

②POWER cable

1PC

③ User Manual

1PC

③

⑥

Specifications

：

*Input Voltage:AC100-240V 50/60Hz

*Max. Power: 300W

*Net Weight: 16.5kg

*Gross Weight: 20kg

*Production size: 76.76*29.73*27.37CM

*Packing size: 86*37*35cm(1pc/carton)

DMX-512 CONTROL CONNECTIONS

Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other

side to the male 3-pin XLR input of the moving head. You can chain multiple

Moving head together through serial linking. The cable needed should be two core, screened

cable with XLR input and output connectors. Please refer to the diagram below.

DMX-512 connection with DMX terminator

⑦

DMX Input

3-Pin XLR

DMX512 Out DMX512 In

3-Pin XLR 3-Pin XLR

1:Ground

2:Data(-)

3:Data(+)

COMMON

DMX+

DMX-

120Ω

Pin2

Pin3

DMX INPUT

DMX OUTPUT

POWER IN

⑧

For installations where the DMX cable has to run a long distance or is in an electrically noisy

environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps

in preventing corruption of the digital control signal by electrical noise. The DMX terminator is

simply an XLR plug with a 120 Ω resistor connected between pins 2 and 3,which is then

plugged into the output XLR socket of the last fixture in the chain. Please see illustrations

below.

Product Feature

Ø 2 kinds of running model

n External control mode (Slave model)

u DMX 512 controller control(2 kinds channel modes)

u Master/salve model control (auto match the signal from controller and the Master

light, no need to set by menu)

n static mode (Master model)

u It can fix any color without the controller ,also work this color with strobe

Ø Non-linear dimmer and linear dimmer

n The speed of dimmer can be set under the controller control

Ø Screen Protect

n It will enter blank screen without any operate on the keyboard in 30 seconds . Press any

keys then it can quit screen protection.

Ø Temperature Protection

n It can be set to temperature protection mode

Ø Can be Reverse display

⑨

Multi-light working in the same time

When using controller to control multi lights to work in strobe, the controller just send the

channel data . The strobe effect will be depend on each light itself . And please take attention for

the follow situation:

1. There will be many situations make the lights are not synchronization in the beginning. (For

example: the different time of opening the light , or different time of them connect to the

controller) .In this case, you can change value of the controller( for example push 20 to 0, and

back to 20), then it can be synchronization.

2. Due to crystal frequency of different lights are not the same exactly, so it may not be

synchronization after long time.

3. If need to keep synchronization for long time, there are two ways to do so:

A. Using the controller to edit program make the strobe, auto run effect,then they must be

synchronization.

B. Using the Maser/Slave model

Main Menu

6.1 Main Menu

1 2

Reverse Display

Running Status

Vice Menu Button

⑩

6.2 Operation Status

Mode

Display

Description

DMX Mode

Dxxx

“D”stand for DMX mode

Temperature

Mode

M-WP

“M”stand for stand Master, “WP”stand for“White

Point”

DMX Menu

Enter DMX mode:

1. If you are in DMX mode,the main menu will turn into DMX menu automatically after 5 seconds

2. Menu of DMX address (DMX mode) will turn into DMX menu automatically after 5 seconds

DMX Menu Operation:

Inhaltsverzeichnis

Andere Gamma+ Beleuchtungsausrüstung Handbücher

Gamma+

Gamma+ I-Pix Bedienungsanleitung

Gamma+

Gamma+ Cove LED 200 Bedienungsanleitung

Gamma+

Gamma+ Rose LED Zoom Bedienungsanleitung

Gamma+

Gamma+ LED Leko 200 Bedienungsanleitung

Gamma+

Gamma+ Silhouette Oculus XL Z Bedienungsanleitung

Gamma+

Gamma+ Rose XT LED 200 Zoom Montageanleitung

Gamma+

Gamma+ Luxe Cove 200 VW Bedienungsanleitung

Gamma+

Gamma+ Borealis XL Z Bedienungsanleitung

Gamma+

Gamma+ Luxe Bianco 600 Bedienungsanleitung

Gamma+

Gamma+ Leko Toro Bedienungsanleitung

Gamma+

Gamma+ Starburst 7x18w Bedienungsanleitung

Gamma+

Gamma+ Ditto 8 IP Bedienungsanleitung

Gamma+

Gamma+ Penn Mini Bedienungsanleitung

Gamma+

Gamma+ Rayon Bedienungsanleitung

Gamma+

Gamma+ TX6 LED 300 Beam Bedienungsanleitung

Gamma+

Gamma+ Helix 7 Bedienungsanleitung

Gamma+

Gamma+ Torrent Spot IP Bedienungsanleitung

Gamma+

Gamma+ TX5 Spot Bedienungsanleitung

Gamma+

Gamma+ Oculus 40 Bedienungsanleitung

Gamma+

Gamma+ Xenon Par Bedienungsanleitung

Gamma+

Gamma+ Penn XL Bedienungsanleitung

Gamma+

Gamma+ Luxe Toro 600 RGBW Bedienungsanleitung

Gamma+

Gamma+ Borealis R Bedienungsanleitung

Gamma+

Gamma+ Starburst Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung