GRAPHTEC MP303-04 Bedienungsanleitung

303-04

USER’S MANUAL

MANUAL NO. MP303-UM-151

TO ENSURE SAFE AND CORRECT USE

•To ensure safe and correct use of your plotter, read this Manual thoroughly before use.

•After having read this Manual, keep it in a handy location for quick reference as needed.

•Do not permit small children to touch the plotter.

•The following describes important points for safe operation. Please be sure to observe them strictly.

Conventions Used in This Manual

To promote safe and accurate use of the plotter as well as to prevent human injury and property damage,

safety precautions provided in this manual are ranked into the three categories described below. Be sure you

understand the difference between each of the categories.

DANGER

This category provides information that, if ignored, is highly likely to cause fatal or serious injury

to the operator.

WARNING

This category provides information that, if ignored, is likely to cause fatal or serious injury to the

operator.

CAUTION

This category provides information that, if ignored, could cause injury to the operator or physi-

cal damage to the plotter.

Description of Safety Symbols

The symbol indicates information that requires careful attention (which includes warnings).

The point requiring attention is described by an illustration or text within or next to the

symbol.

The symbol indicates action that is prohibited. Such prohibited action is described by an

illustration or text within or next to the symbol.

The symbol indicates action that must be performed. Such imperative action is described by

an illustration or text within or next to the symbol.

Safety Precautions

WARNING

During a plotting operation, do not touch theY bar,

carriage, and other moving parts.

•Such action may cause human injury.

Even when the plotter is stopped, it may suddenly

start operating if it receives data, so be sure to

keep your hands, hair, and so forth away from the

vicinity of the plotter’s moving parts such as theY

bar and the pen carriage.

•Such action may cause human injury.

Do not connect the plotter to a non-rated power

supply.

•Use of a different supply voltage may result in elec-

trical shock or a fire hazard due to current leakage.

If the plotter generates smoke, is too hot, emits a

strange odor, or otherwise functions abnormally,

do not continue using it. Turn off its power and

unplug its power cable from the elec-

trical socket.

•Use of the plotter in such status may

result in a fire hazard or electrical

shock.

•After confirming that smoke is no longer being gen-

erated, contact your sales

representative or nearest

vendor to request repair.

•Never try to perform repair

yourself. Repair work by in-

experienced personnel is

extremely dangerous.

No touching

Keep away

Use prohibited

Prohibited

Do not disassemble or remodel the plotter.

•Such action may cause electrical shock or a fire haz-

ard due to current leakage.

•Contact with the high-voltage parts within the plotter

may cause electrical shock.

•If the plotter requires repair, contact your sales rep-

resentative or nearest vendor.

Do not use the plotter in a location where it will be

exposed to water, rain or snow.

•Such location may cause electrical shock or a fire

hazard due to current leakage.

No disassembl

Avoid water

Beware of electrical shock

Do not allow dust or metallic matter to adhere to

the power plug.

•A dirty power plug may result in electrical shock or a

fire hazard due to current leakage.

Beware of electrical shock

Prohibited

Unplug the power

cable from the socket

Do not use the power cable if it is damaged.

•Use of a damaged cable may result in electrical shock

or a fire hazard due to current leakage.

•Replace the power cable with a new one.

iii

Safety Precautions (Continued)

CAUTION

Prohibited

Avoid water

Beware of electrical shock

Prohibited

Do not use or store the plotter in a location ex-

posed to direct sunlight or the direct draft of an air

conditioner or heater.

•Such location may impair the performance of the plot-

ter.

Do not place any receptacle containing water or

other fluid on top of the plotter.

•Fluid falling inside the plotter may cause electrical

shock or a fire hazard due to current leakage.

Do not use or store the plotter in an excessively

dusty or humid location.

•Such location may impair the performance of the plot-

ter.

Do not install, use, or store the plotter in a loca-

tion subject to excessive mechanical vibration or

electrical noise.

•Such location may impair the performance of the plot-

ter.

Unplug the power

cable from the socket

If water or foreign matter enters inside the plotter,

do not continue using it.Turn off its power and un-

plug its power cable from the electrical socket.

•Use of the plotter in such status may result in electri-

cal shock or a fire hazard due to current leakage.

•Contact your sales representative or nearest vendor

to request repair.

Do not clean the plotter using a volatile solvent

(such as thinner or benzene).

•Such action may impair its performance.

Prohibited

When disconnecting the power cable or an inter-

face cable, do not pull on the cable.

•Such action will damage the cable, resulting in a fire

hazard or electrical shock. Be sure to hold the power

cable’s plug or the interface cable’s connector.

Do not attempt to lubricate the plotter’s mecha-

nisms.

•Such action may cause it to break down.

Safety Precautions (Continued)

CAUTION

Be sure to use Graphtec ink pen tips only.

•Using non-Graphtec pen tips may lower the perfor-

mance or cause a malfunction or a failure.

Do not disassemble the ink tip.

•Such action may cause a failure.

Always clean the pen caps.

•Dried ink may clog the pen tip and make it unusable.

Do not put magnetic cards, magnetic tapes and

floppy disks etc. close to the pen carriage and pen

station.

•Such action may corrupt data because these parts

contain magnets.

Do not attach or remove the pen to/from the pen

carriage.

•Such action may cause a malfunction.

Prohibited

No disassembly

Clean the

pen caps

WARNING:

The United States Federal Communications Commission has specified that the following notice must be brought

to the attention of users of this product.

FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY

INTERFERENCE STATEMENT

NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct the interference at

his own expense.

USE SHIELDED CABLES

To comply with FCC Class A requirements, all external data interface cables and connectors must be properly

shielded and grounded. Proper cables and connectors are available from GRAPHTEC’s authorized dealers or

manufacturers of computers or peripherals. GRAPHTEC is not responsible for any interference caused by

using cables and connectors other than those recommended or by unauthorized changes or modifications to

this equipment. Unauthorized changes or modifications could void the user’s authority to operate the equip-

ment.

Selecting a Power Cable

Be sure to refer to the following tables if you wish to use a cable other than the one supplied as an accessory.

Table 1 100 V to 120 V Power Supply Voltage Range

Supply

Plug Configuration Plug Voltage Reference Power Cable

Type Selector Standards

Settings

North ANSI C73.11 UL Listed

America NEMA 5-15

125 V 100/120 V UL498/817/62 Type SJT

10 A CSA22.2 No.18AWG x 3

NO.42/21/49 300 V, 10 A

Table 2 200 V to 240 V Power Supply Voltage Range

Supply

Plug Configuration Plug Voltage Reference Power Cable

Type Selector Standards

Settings

Europe CEE(7)VII TYPE: H05VV-F

250 V 200 V IEC320 3 x 1.0 mm2

10 A CEE13

UK BS1363 TYPE: H05VV-F

250 V 200 V BS4491 3 x 1.0 mm2

5 A BS6500

Australia AS3112 TYPE: OD3CFC

250 V 200 V AS3109 3 x 1.0 mm2

10 A AS3191

North UL Listed

America ANSI C73.20

250 V 200 V NEMA 6-15 Type SJT

15 A UL 198.6 No.18AWG x 3

300 V, 10 A

Switzerland SEV1011 TYPE: H05VV-F

250 V 200 V SEV1004 3 x 0.75 mm2

6 A SEV1012

h-1

PREFACE

Thank you for purchasing the MP303-04 plotter. This pen plotter incorporates a digital servo drive to perform

plotting operations at high speed and high precision.

To ensure optimum use of its various functions, be sure to read this manual thoroughly before use.

■Notes on the Use of This Manual

ted.

(2) The specifications and other information in this manual are subject to change without notice.

(3) While every effort has been made to supply complete and accurate information about this product, please

address any inquiries about unclear information, possible errors, or other comments to Graphtec Corpora-

tion.

(4) Notwithstanding the preceding paragraph, Graphtec Corporation assumes no liability for damages result-

ing from the use of the information contained herein or of the product.

■Registered Trademarks

The names of companies, logos, and products mentioned herein are registered trademarks or trademarks of

their respective companies.

■Copyrights

All copyrights regarding this manual belong to Graphtec Corporation.

h-2

Unpacking Your Plotter

After unpacking your plotter and before actual use, be sure to visually inspect the plotter and to confirm the

presence of all standard accessories.

■Visual inspection

Carefully check the exterior of the plotter. If you detect a flaw or other defect, please contact the vendor where

you purchased this plotter.

■Checking the standard accessories

Make sure that you have all the parts listed in the following table. If any part has been omitted, please contact

your vendor.

Exterior View Part Name Description Qty.

1AC adapter SA45-3129 1

2Cable AC cable 1

3USB cable (1.5 m) CBL0106-1-5M 1

4Water based KF550-S1 1 pack

fiber-tip pens (

2 of black, 1 each of red, blue, green

)

5Plotting paper Coated paper (PL501) 5 sheets

6Soft plastic cover For MP303-04 plotters 1

7Paper alignment To mark positions on the writing 1 sheet

stickers panel for paper alignment (8 stickers)

h-3

Exterior View Part Name Description Qty.

8Rubber insert 8

9Tilt stand To stand an MP303-04 plotter 2

at a 60°angle

QuickStart Manual

10 and 1 each

Usage Precautions

11 User guide CD-ROM 1

Inhaltsverzeichnis

Andere GRAPHTEC Plotter Handbücher

GRAPHTEC

GRAPHTEC CE7000-40 Bedienungsanleitung

GRAPHTEC

GRAPHTEC CE6000 SERIES Benutzerhandbuch

GRAPHTEC

GRAPHTEC FC8600 SERIES Benutzerhandbuch

GRAPHTEC

GRAPHTEC FC9000 Series Benutzerhandbuch

GRAPHTEC

GRAPHTEC FC8000 Series Bedienungsanleitung

GRAPHTEC

GRAPHTEC CE6000 SERIES Bedienungsanleitung

GRAPHTEC

GRAPHTEC FC4500 Bedienungsanleitung

GRAPHTEC

GRAPHTEC FC8600 SERIES Bedienungsanleitung

GRAPHTEC

GRAPHTEC FC5100A-75 Bedienungsanleitung

GRAPHTEC

GRAPHTEC CE5000-60 Bedienungsanleitung

GRAPHTEC

GRAPHTEC FCX4000 SERIES Benutzerhandbuch

GRAPHTEC

GRAPHTEC FC7000 Series Handbuch

GRAPHTEC

GRAPHTEC FCX4000 SERIES Benutzerhandbuch

GRAPHTEC

GRAPHTEC FCX4000 SERIES Bedienungsanleitung

GRAPHTEC

GRAPHTEC Craft ROBO CC200 Benutzerhandbuch

GRAPHTEC

GRAPHTEC CE6000-120AP Benutzerhandbuch

GRAPHTEC

GRAPHTEC FCX2000 SERIES Benutzerhandbuch

GRAPHTEC

GRAPHTEC CELITE-50 Bedienungsanleitung

GRAPHTEC

GRAPHTEC CE7000 Series Bedienungsanleitung

GRAPHTEC

GRAPHTEC FC9000 Series Benutzerhandbuch

GRAPHTEC

GRAPHTEC CE7000-130AP Benutzerhandbuch

GRAPHTEC

GRAPHTEC CE7000-130AP Bedienungsanleitung

GRAPHTEC

GRAPHTEC Craft ROBO CC100-20 Programmierhandbuch

GRAPHTEC

GRAPHTEC FC7000-75 Bedienungsanleitung

Beliebte Plotter Handbücher anderer Marken

MUTOH

MUTOH Kona 760 Bedienungsanleitung

HP 7475a Bedienungsanleitung

Vulcan-Hart

Vulcan-Hart FC-500VC Bedienungsanleitung

Roland

Roland TrueVIS VG-640 Betriebsanleitung

Furuno

Furuno RP-180 Bedienungsanleitung

Roland

Roland VersaCamm SP-540V Bedienungsanleitung

MIMAKI

MIMAKI CF2 Series Bedienungsanleitung

Ioline

Ioline Summit Bedienungsanleitung

Summa

Summa S CLASS Bedienungsanleitung

Gerber Technology

Gerber Technology GERBERplotter MP Series Bedienungsanleitung

Furuno

Furuno RP-17 Bedienungsanleitung

HP 7470A Bedienungsanleitung

SII

SII LP-1010 Bedienungsanleitung

Great Computer

Great Computer JII-61 Bedienungsanleitung

Roland

Roland VersaUv LEF - 12i Bedienungsanleitung

Lectra

Lectra Alys 120 Bedienungsanleitung

MUTOH

MUTOH Ultima SC-850D Bedienungsanleitung

Skycut

Skycut D Series Bedienungsanleitung